Description

Solid colour products

Mirrorcryl 2k Mixing kits

Automotive transport ,truck and commercial and Locomotive colour range.

A tough two pack high performance acrylic enamel as a result can be used for automotive, commercial vehicle and equipment. New work and refinishing for universal application therefore having universal transport applications.
Exceptional colour matching and UV resistance is a key feature but most of all it is extremely durable with hi gloss .
The high standard to be met by commercial and original equipment finishes are reflected in the chemical resistance and abrasion resistance of Mirrorcryl due to the high quality resins used in the system,

Slow thinner may be needed to refinish larger vehicles therefore aiding longer wet edge time.

Mixing Instructions

Mirrorcryl mixed colour 100 parts
Mirrorcryl MS Hardener 50 parts
Every thinner fast 50 parts
Every thinner slow 50 parts

Application Substrates
Mirrorcryl ready mixed colours can be applied over sanded original finishes except thermoplastic acrylic. – Sanded fibreglass surfaces. – Washfiller etch – Hi-fil 2k Primer – Anti-corrosive primer – Zp Primer Shades – Tempo Filler Shades
Surface preparation
Degreaser with Quickwipe degreaser then Dry sand with p320-p400 grade paper. Wet sand with P800 or P1000 grade paper. Application Mixing Instructions Mixing ratio is 100 parts base: 50 parts activator by volume, 10 -20% thinner of total volume. The mixed material is then ready for application normal pot life up to 4 hours AT 20°c apply 2 full coats 20 mins between each coat.”

Mirrorlaq Ready mixed

Quick drying Quality Nitrocellulose for automotive, bike commercial vehicle part repairs or repaints and therefore can also be used on Industrial general machine and implements work and exterior woodwork, extremely fast flash-off and polish to a full gloss.

Mixing Instructions
Mixing ratio is 100 parts Mirrorlaq 100-100 parts Mirrorfast thinner.
With some colours, a greater amount of thinner will enhance the sprayablity flow and polishablity.
Metallic colours mixing ratio is 100 Mirrorlaq 150 parts Mirrorlaq thinner.

Application process
Spray single coats until full opacity is achieved (with most colours 3-4 single coats is sufficient). Flash off times will vary depending on temperature, the type of thinners used and conditions of application, please allow each coat to become touch dry before applying the following coat.

See colour listing below:
Mirrorlaq is normally mixing in all solid colours (i.e. red blue green), we can mix Metallic and Pearl coat colours with restrictions that it would be a repaint match only.

Mirrorfast ready mixed

Quick air drying TPA acrylic enamel for automotive part repairs or repaints and also for Industrial work and exterior woodwork has a extremely fast flash-off as a result will polish to a full gloss quickly, Based on non yellowing acrylic enamel this product is durable easy to use and easy to blend.

Appearance
Full Gloss is available and in addition Satin and matt are also available to order

Additives
107.005 – Mirrorfast fast thinner – for normal speed and performance and high gloss.

Coverage
Coverage of 8-9m sq/mtr per Litre per coat

Application Substrates
Mirrorfast ready mixed colours are applied over sanded and degreased original finishes due to the substrate needs sanding for adhesion, also Tempo-filler shades and Washfiller etch primer filler.

Surface preparation
Degrease first of all with Quick wipe degreaser.
Dry sand with p320-p400 grade paper.
Wet sand with p800-p1000 grade paper.
Degrease with Quick wipe degreaser.

Mixing Instructions
Mixing ratio is 100 parts Mirrorfast 100-150 parts Mirrorfast thinner.
With some colours, a greater amount of thinner is needed and therefore will enhance the sprayablity, flow and polishablity.
Metallic colours mixing ratio is 100 Mirrorfast 150 parts Mirrorfast thinner.

Spraying viscosity
12-15s Din cup 4 at 20°c (15-19s BSB4 cup)
Spray gun fluid tip and working pressure
tip pressure
Gravity feed Spray gun 1.5mm 2-4 bar
(30-60 psi)
Suction feed Spray gun 1.8mm 2-4 bar
(30-60 psi)

Application process
Spray single coats until full opacity is achieved (with most colours 3-4 single coats is sufficient). Flash off times will vary depending on temperature, the type of thinners used and conditions of application, please allow each coat to become touch dry before applying the following coat.
Satin and Matt colours must have correct film thickness.

Blending and fading out techniques:
Fade-outs are extremely easy with Mirrorfast as you can reduce pressure to (5-7psi), consequently dissolve over spray by fading pure Mirrorfast slow thinner or RA Blending thinner immediately after last coat.

Drying
Dust free 5 mins
Tack free 15 mins
Touch dry 30 mins

Recoatability.
Relocatable after correct flash-off times

Polishing
Areas may have a light flat with P1200 Wet or Dry and polished when dry with reflection finishing surfaces.

CV Polyurethane Ready mixed

Description
C.V Polyurethane is an advanced formula One Pack Synthetic Enamel with fast drying properties therefore making it suitable for Car and commercial vehicles Trucks and vans, Machinery, Implement and metal equipment Full Gloss

Coverage
Coverage of 8-10m sq/mtr per ltr per coat

Application Substrates
C.V Polyurethane ready mixed colours can be applied over sanded original finishes, except thermoplastic acrylic finishes because an application of a barrier coat would be required.
– Washfiller Etch -on steel or aluminium alloys as a result will give superior adhesion
– ZP Primer (Shades) (zinc phosphate)
– Mirrorcryl Hi- Fil primer (2k) as a primer would consequently improve protection and give uniformity
– Anti-corrosive primer.
– Mirror clad MIO Coating
– W/B MIO Armour plate primer.
– Plaz plastic primer on rigid plastic components
– White ground coat are needed on fluorescent colours due to semi transparency of the fluorescent pigment

Surface preparation
Dry sand with p320-p400 free cut paper
Wet sand with p800-p1000 wet or dry paper.
Re coat wet on wet (non sand) primers when flash-off times have been observed.

Spraying Viscosity
C.V Polyurethane ready mixed colours can be thinned 5-1 to a spraying viscosity of 20-28 secs Din4 at 20°c (25-35 secs BSB4 Cup).

Hot Spray Application
Hot application is possible when the product is heated to a temperature of 60-70°c, and one full coat is applied, no thinning is required.

Brush Application
You need to apply at unthinned viscosity using a large brush for which 2 coats is normally applied
To slow CV polyurethane we would recommend an addition of 10% slow thinners.

Application
Spray one single medium coat allowing 20 minutes flash off (until touch dry).
Spray one further full wet coat to full gloss, or double header coat.

Drying
20°c metal temperature
Dust free 40 mins
Tack free 4 hr
Tape time 6 hrs
Hard dry 16 hrs

CV Coachpaint Ready mixed

Description
C.V Coachpaint is an advanced formula One Pack Alkyd Synthetic Enamel with fast drying properties therefore will be suitable for commercial vehicles Trucks and vans, Machine and implements, wood and steelwork, Cladding, Joinery products, Exterior building structures, fascias, garden structures, Rail and heavy goods vehicles,
Coach paints are is a traditional produces for brushing or spraying and are slow drying but with High gloss.

Spraying Viscosity
C.V Coachpaint ready mixed colours can be thinned 5-1 to a spraying viscosity of 20-28 secs Din4 at 20°c (25-35 secs BSB4 Cup).

Application Substrates
C.V Coachpaint ready mixed colours can be applied over sanded original finishes, except thermoplastic acrylic and therefore will requires the application of a barrier coat.
– Washfiller Etch -on steel or aluminium alloys as a result will give superior adhesion
– ZP Primer (Shades) (zinc phosphate)
– Mirrorcryl Hi- Fil primer (2k) as a primer would consequently improve protection and give uniformity
– Anti-corrosive primer.
– Mirror clad MIO Coating
– W/B MIO Armour plate primer.
– Plaz plastic primer on rigid plastic components
– White ground coat are needed on fluorescent colours due to semi transparency of the fluorescent pigment

Surface preparation
Dry sand with p320-p400 free cut paper
Wet sand with p800-p1000 wet or dry paper.

Hot Spray Application
Hot application is possible when the product is heated to a temperature of 60-70°c, and one full coat is applied, no thinning is required.

Brush Application
Apply at unthinned viscosity using a large brush also 2 coats is normally applied
An addition of 10% WS Thinners is recommended.
It is possible to only apply one coat because you would apply a correct colour undercoat first

Lazergloss Brushable

Description
This is an exterior durable brushable paint finish in which customers can buy the product in a range of beautiful Gloss Satin of Matt finishers therefore it results in a Hard and tough and fast drying product making it a Ideal Industrial and Decorative coating for Woodwork, metalwork repairs and Industrial Applications, Use in model painting this is base on a non Yellowing and Blend of solvents

Products
Lazergloss is available in a wide variety of colours because the product can be mixed in the full range of solid colours, British standard colours and RAL Colours, Pearl coat translucent and specialist colours to order.
Computer colour match are now achievable as a result of using your colour standard sample you can provided.

Substrates to which this Product can be Applied
Woodwork
ZP Primer Shades
Anti-corrosive primer
Primed metalwork and most painted and cured finishes

Surface Preparation
Surfaces should be free of all loose dust and smooth and therefore the use of p400 free cut paper is recommended.

Mixing Ratio
The product is supplied Ready for use but can be thinned if longer Brush ability is required with up to 10% WS Thinner
This is traditionally a brush applied material but can be spray applied by using alternatively Mirrorfast Thinner as the solvent for spray.
The lazergloss colours are mixed 1-1 please note when sprayed approx, 4 coats would be the same as one coat brushed.

Application process

By Brush
Apply 3 coats as a result the drying time will be between coats of 3 hour at 20°c centigrade
When each coat is dry it can be sanded with p400 or Fibral hand pads (ultra Fine).
If a matched coloured undercoat (ZP Primer Shades) is used it is possible to used less coats to achieve coverage because better opacity will be achieved

Finishing process
After the product has dried, any small contamination in the coating may be sanded with P2000 microfine abrasive and then polished to a finish with Mirror Reflection finishing Surfacer.