Loading AI tools
Material used in the manufacture of printed circuit boards From Wikipedia, the free encyclopedia
Solder paste is used in the manufacture of printed circuit boards to connect surface mount components to pads on the board. It is also possible to solder through-hole pin in paste components by printing solder paste in and over the holes. The sticky paste temporarily holds components in place; the board is then heated, melting the paste and forming a mechanical bond as well as an electrical connection. The paste is applied to the board by jet printing, stencil printing or syringe; then the components are put in place by a pick-and-place machine or by hand.
 | This article needs additional citations for verification. (March 2017) |
A majority of the defects in circuit-board assembly are caused due to issues in the solder-paste printing process or due to defects in the solder paste. There are many different types of defects possible, e.g. too much solder, or the solder melts and connects too many wires (bridging), resulting in a short circuit. Insufficient amounts of paste result in incomplete circuits. Head-in-pillow defects, or incomplete coalescence of ball grid array (BGA) sphere and solder paste deposit, is a failure mode that has seen increased frequency since the transition to lead-free soldering. Often missed during inspection, a head-in-pillow (HIP) defect appears like a head resting on a pillow with a visible separation in the solder joint at the interface of the BGA sphere and reflowed paste deposit.[1] An electronics manufacturer needs experience with the printing process, specifically the paste characteristics, to avoid costly re-work on the assemblies. The paste's physical characteristics, like viscosity and flux levels, need to be monitored periodically by performing in-house tests.
When making PCBs (printed circuit boards), manufacturers often test the solder paste deposits using SPI (solder paste inspection). SPI systems measure the volume of the solder pads before the components are applied and the solder melted. SPI systems can reduce the incidence of solder-related defects to statistically insignificant amounts. Inline systems are manufactured by various companies such as Delvitech (Switzerland), Sinic-Tek (China), Koh Young (Korea), GOEPEL electronic (Germany), CyberOptics (US), Parmi (Korea) and Test Research, Inc. (Taiwan).[2] Offline systems are manufactured by various companies such as by VisionMaster, Inc. (US) and Sinic-Tek (China).
A solder paste is essentially powdered solder suspended in flux paste. The tackiness of the flux holds components in place until the soldering reflow process melts the solder. As a result of environmental legislation, most solders today, including solder pastes, are made of lead-free alloys[citation needed].
The size and shape of the metal particles in the solder paste determines how well the paste will "print". A solder ball is spherical in shape; this helps in reducing surface oxidation and ensures good joint formation with the adjoining particles. Irregular particle sizes are not used, as they tend to clog the stencil, causing printing defects. To produce a quality solder joint, it's very important for the spheres of metal to be very regular in size and have a low level of oxidation[citation needed].
Solder pastes are classified based on the particle size by IPC standard J-STD 005.[3] The table below shows the classification type of a paste compared with the mesh size and particle size.[4] Some suppliers use proprietary particle size descriptions, Henkel/Loctite descriptions are given for comparison.[5]
| Type designation [IPC] | Mesh size in lines-per-inch | Max. size in μm (no larger than) |
Max. size in μm (less than 1% larger than) |
Particle size in μm (80% min. between) |
Avg. size in μm |
Min. size in μm (10% max. less than) |
Henkel Powder Description[5] |
|---|---|---|---|---|---|---|---|
| Type 1 | 150 | 150-75 | 20 | ||||
| Type 2 | -200/+325 | 75 | 75–45 | 60 | 20 | ||
| Type 3 | -325/+500 | 45 | 45–25 | 36 | 20 | AGS | |
| Type 4 | -400/+635 | 38 | 38–20 | 31 | 20 | DAP | |
| Type 5 | -500/+635 | 30 | 25 | 25–10 | 10 | KBP | |
| Type 6 | -635 | 20 | 15 | 15–5 | 5 | ||
| Type 7 | 15 | 11 | 11–2 | ||||
| Type 8 | 11 | 10 | 8–2 |
According to IPC standard J-STD-004 "Requirements for Soldering Fluxes", solder pastes are classified into three types based on the flux types:
Rosin based fluxes are made with rosin, a natural extract from pine trees. These fluxes can be cleaned if required after the soldering process using a solvent (potentially including chlorofluorocarbons) or saponifying flux remover.
Water-soluble fluxes are made up of organic materials and glycol bases. There is a wide variety of cleaning agents for these fluxes.
A no-clean flux is designed to leave only small amounts of inert flux residues. No-clean pastes save not only cleaning costs, but also capital expenditures and floor space. However, these pastes need a very clean assembly environment and may need an inert reflow environment.
In using solder paste for circuit assemblies, one needs to test and understand the various rheological properties of a solder paste.
Solder paste is typically used in a stencil-printing process by a solder paste printer,[6] in which paste is deposited over a stainless steel or polyester mask to create the desired pattern on a printed circuit board. The paste may be dispensed pneumatically, by pin transfer (where a grid of pins is dipped in solder paste and then applied to the board), or by jet printing (where the paste is ejected onto the pads through nozzles, like an inkjet printer).
As well as forming the solder joint itself, the paste carrier/flux must have sufficient tackiness to hold the components while the assembly passes through the various manufacturing processes, perhaps moved around the factory.
Printing is followed by a complete reflow soldering process.
The paste manufacturer will suggest a suitable reflow temperature profile to suit their individual paste. The main requirement is a gentle rise in temperature to prevent explosive expansion (which can cause "solder balling"), yet activate the flux. Thereafter, the solder melts. The time in this area is known as Time Above Liquidus. A reasonably rapid cool-down period is required after this time.
For a good soldered joint, the proper amount of solder paste must be used. Too much paste may result in a short circuit; too little may result in poor electrical connection or physical strength. Although solder paste typically contains around 90% metal in solids by weight, the volume of the soldered joint is only about half that of the solder paste applied.[7] This is due to the presence of flux and other non-metallic agents in the paste, and the lower density of the metal particles when suspended in the paste as compared to the final, solid alloy.
As with all fluxes used in electronics, residues left behind may be harmful to the circuit, and standards (e.g., J-std, JIS, IPC) exist to measure the safety of the residues left behind.
In most countries, "no-clean" solder pastes are the most common; in the United States, water-soluble pastes (which have compulsory cleaning requirements) are common.
Solder paste must be refrigerated when transported and stored in an airtight container at a temperature between 0-10 °C. It should be warmed to room temperature for use.
Recently, new solder pastes have been introduced that remain stable at 26.5 °C for one year and at 40 °C for one month.[8]
Exposure of the solder particles, in their raw powder form, to air causes them to oxidize, so exposure should be minimized.
The main reason why evaluation of solder paste is necessary, is because 50-90% of all defects result from printing problems. Hence, paste evaluation is critical.
This procedure is quite thorough, yet minimizes the amount of testing required to differentiate between excellent and poor solder pastes. If multiple solder pastes are evaluated, the procedure can be used to eliminate the poor pastes from their poor printing quality. Further testing, such as solder reflow performance, solder joint quality, and reliability testing can then be performed on the solder paste finalists.
The main concerns about solder paste are:
These three concerns helped to spawn three enclosed systems for printing.
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
