Chemical admixtures

Category of water-reducing admixture Chemical type Additional air content (% by volume) Reference... [Pg.63]

Specialty chemicals producers must find an answer to the exodus of customers to emerging markets, which not only threatens to break up established supplier-customer relationships, but has the potential to destabilize entire segments. This is particularly true for formulation-based segments such as admixture chemicals for the concrete industry, which depend on close interaction with customers. What happened to textile dyes in Europe is just one particularly striking example the migration of the European textile industry to Asia and subsequent emergence... [Pg.100]

Keywords Shrinkage reducing admixtures, chemical shrinkage, cement pastes, compressive strength. [Pg.105]

Many factors influence the amount of entrained air. They include dosage, slump, aggregates, temperature, inclusion of other admixtures, chemical composition of cement, mixing, vibration, etc. [Pg.174]

Positive-Tone Photoresists based on Dissolution Inhibition by Diazonaphthoquinones. The intrinsic limitations of bis-azide—cycHzed mbber resist systems led the semiconductor industry to shift to a class of imaging materials based on diazonaphthoquinone (DNQ) photosensitizers. Both the chemistry and the imaging mechanism of these resists (Fig. 10) differ in fundamental ways from those described thus far (23). The DNQ acts as a dissolution inhibitor for the matrix resin, a low molecular weight condensation product of formaldehyde and cresol isomers known as novolac (24). The phenoHc stmcture renders the novolac polymer weakly acidic, and readily soluble in aqueous alkaline solutions. In admixture with an appropriate DNQ the polymer s dissolution rate is sharply decreased. Photolysis causes the DNQ to undergo a multistep reaction sequence, ultimately forming a base-soluble carboxyHc acid which does not inhibit film dissolution. Immersion of a pattemwise-exposed film of the resist in an aqueous solution of hydroxide ion leads to rapid dissolution of the exposed areas and only very slow dissolution of unexposed regions. In contrast with crosslinking resists, the film solubiHty is controUed by chemical and polarity differences rather than molecular size. [Pg.118]

Adipic acid is an irritant to the mucous membranes. In case of contact with the eyes, they should be flushed with water. It emits acrid smoke and fumes on heating to decomposition. It can react with oxidizing materials, and the dust can explode ia admixture with air (see Table 3). Fires may be extinguished with water, CO2, foam, or dry chemicals. [Pg.246]

For special high strength appHcations, ie, up to 69 MPa (10,000 psi), special formulations of Pordand cement concretes have been developed. These ate based on the use of chemical and mineral admixtures. The typical mineral admixtures ate fumed siUca and other po22olanics. The chemical admixtures ate generally chemicals termed supetplastici2ets that allow very low water to cement ratios, ie, between 0.4 and 0.25, and reduce the amount of water needed to provide plasticity or dow to the concrete. PubHc works appHcations take just under 32% of the total Pordand cement market streets and highways represent 68% of this usage, and water and waste account for 23%. [Pg.324]

For DTB films obtained by CVT inhomogenous distribution of out-of-framework cations and admixture capture ai e obseiwed. The aim of the present work is to use imaging X-ray photoelectron spectroscopy (i-XPS) for chemical state mapping which enable future optimization of the CVT technology. The P, O and Hg content in the DTB may be varied during the CVT. [Pg.450]

The precautions naturally vary in each case. For example, to avoid improper admixture of chemicals will require ... [Pg.91]

Admixture of chemicals By mistake, e.g. wrongly identified In wrong proportions In wrong circumstances In wrong sequence... [Pg.105]

Reactive chemical hazards may arise from the inherent properties of the chemicals handled, used or disposed of and/or from their admixture or processing. [Pg.228]

This closeness of 0 to zero explains the existence of a gas-oversaturated solution area in the polymer melt, when P < Pg, but the entire volume of gas remains in the solution. The degree of oversaturation, particularly upon free foaming (not in flow) can be 2- to 3-fold. In real polymer compositions, there are always solid admixtures, which have poor wetting areas. This reduces the degree of oversaturation at the interface melt-molding tool. Moreover, bubble nuclei can result from fragmentation of gas bubbles in the polymer [16]. Another factor that promotes the formation of bubble nuclei is the presence of localized hot points in the polymer melt they act as nuc-leation centres. Hot points appear either after a chemical reaction in the melt polymer [17], or in overheated areas on the surface of metal equipment [18]. Density of nucleation can be improved via introduction of various agents that reduce tension of the polymer [19]. [Pg.103]

Where the instructions for use of the product involve admixture or dilution with drinks or other materials, appropriate compatibility data will be required. Factors to consider include ease and rate of dissolution, homogeneity, chemical and physical stability over the period of use, particle size, etc. [Pg.653]

The dissolution of zinc in a mineral acid is much faster when the zinc contains an admixture of copper. This is because the surface of the metal contains copper crystallites at which hydrogen evolution occurs with a much lower overpotential than at zinc (see Fig. 5.54C). The mixed potential is shifted to a more positive value, E mix, and the corrosion current increases. In this case the cathodic and anodic processes occur on separate surfaces. This phenomenon is termed corrosion of a chemically heterogeneous surface. In the solution an electric current flows between the cathodic and anodic domains which represent short-circuited electrodes of a galvanic cell. A. de la Rive assumed this to be the only kind of corrosion, calling these systems local cells. [Pg.394]

Typical compositions of polymeric GMs are depicted in Table 26.3. As the table shows, the membranes contain various admixtures such as oils and fillers that are added to aid the manufacturing of the FML but may affect future performance. In addition, many polymer FMLs will cure once installed, and the strength and elongation characteristics of certain FMLs will change with time. It is important therefore to select polymers for FML construction with care. Chemical compatibility, manufacturing considerations, stress-strain characteristics, survivability, and permeability are some of the key issues that must be considered. [Pg.1119]

Specifically, the improved solidification (cementation) technology involves the use of (a) a special dry powder admixture for the generation of a nonsoluble crystalline formation deep within the pores and capillary tracts of the concrete—a crystalline structure that permanently seals the concrete against the penetration or movement of water and other hazardous liquids from any direction (b) special nonmetal reinforced bars for enhancing the concrete block s tensile and compressive strengths and (c) a unique chemical crystallization treatment for the waterproofing and protection of the concrete block s surface. [Pg.1231]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...