Assisting flow

The management of production is well described by Hill, but the prime consideration is product flow, and all features of the layout must assist flow. There are some indicators which can be used to measure the quality of the production facilities, and these can be employed to demonstrate the viability of the proposed new layout. [Pg.79]

Alkanesulfonates act as an external lubricant in PVC, polystyrene, and engineering thermoplastics. They have a good release effect and assist flow. Addition is in the concentration range between 0.1 and 2.0 parts per 100 parts resin (phr). Because of their low volatility, alkanesulfonates are also used as a processing aid for high-melting engineering thermoplastics. [Pg.207]

E. Combined Forced and Free Laminar Convection from Vertical Surfaces When Both Are in the Same Direction (Assisting Flows)... [Pg.26]

It is difficult to solve the system of Eqs. (39)—(41) for these boundary conditions. However, certain simplifying assumptions can be made, if the Prandtl number approaches large values. In this case, the thermal boundary layer becomes very thin and, therefore, only the fluid layer near the plate contributes significantly to the heat transfer resistance. The velocity components in Eq. (41) can then be approximated by the first term of their Taylor series expansions in terms of y. In addition, because the nonlinear inertial terms are negligible near the wall, one can further assume that the combined forced and free convection velocity is approximately equal to the sum of the velocities that would exist when these effects act independently. Therefore, for assisting flows at large Prandtl numbers (theoretically for Pr -> oo), Eq. (41) can be rewritten in the form ... [Pg.26]

Yang W. J., "Computer-Assisted Flow Visualization". CRC Press, Inc., Boca Raton, Florida (1994). [Pg.28]

Total mercury in soils can be measured by ICP-MS [330]. Mercury was extracted by using a microwave assisted flow injection system. A complexing agent and surfactant were added to eliminate the long memory effects typically observed with mercury. [Pg.135]

A consideration of the results given in Fig. 9.7 in conjunction with Eqs. (9.35) and (9.36) shows that the buoyancy forces increase the heat transfer rate and wall shear stress in assisting flow and decrease these quantities in opposing flow. If it is assumed that the effect of the buoyancy forces on the heat transfer rate can be neglected, i.e., that the flow can be assumed to be a purely forced convective flow, when ... [Pg.435]

Solution. Here, the buoyancy forces will act in the same dilrection as the forced flow, i.e., assisting flow will exist. In this case, buoyancy force effects on the heat transfer rate will be important if ... [Pg.436]

The results given by this equation with n set equal to 3.5 are compared in Fig. 9.18 with the numerically calculated results for assisting flow for a Prandtl number of 0.7 that were given earlier in Fig. 9.9. [Pg.450]

It will be seen that Eq. (9.70) does, in fact, describe the variation in the mixed convection region with assisting flow to an accuracy that is quite acceptable for most purposes. Eq. (9.66) does, therefore, apply to assisting mixed convective flow over a flat plate. It has been shown that it does, in fact, also describe experimental results for other more complex situations to a good degree of accuracy provided the value... [Pg.450]

Horizontal cylinder, assisting flow, uniform surface temperature 3.5... [Pg.451]

The above discussion applied only to assisting flow and cross flow. Now, it will be noted that Eq. (9.74) indicates that ... [Pg.452]

It will be noted that the above derivation was based on the assumption that dTIdy was negative and that duldy was positive and that the buoyancy forces acted in the -direction, i.e., they applied to assisting flow. In opposing flow, the buoyancy forces act in the opposite direction to the x-axis, this -axis conventionally being taken in the direction of the forced flow. Thus, in general, Eqs. (9.95), (9.96), and (9.97) can be written as ... [Pg.460]

Because, for flow over a heated surface. r>ulc>x is positive and ST/ y is negative. S will normally be a negative. Hence, in assisting flow, the buoyancy forces will tend to decrease e and e, i.e., to damp the turbulence, and thus to decrease the heat transfer rate below the purely forced convective flow value. However, the buoyancy force in the momentum equation tends to increase thle mean velocity and, therefore, to increase the heat transfer rate. In turbulent assisting flow over a flat plate, this can lead to a Nusselt number variation with Reynolds number that resembles that shown in Fig. 9.22. [Pg.461]

Based on results similar to those shown in Fig. 9.23, the conditions under which mixed convection effects are important in assisting flow over a vertical plate can be derived. These conditions are indicated in Fig. 9.24. [Pg.461]

Purely forced, purely free, and mixed convective regions in assisting flow over a vertical plate. (Based on results obtained by Patel K., Armaly B.F., and Chen T.S., Transition from Turbulent Natural to Turbulent Forced Convection Adjacent to an Isothermal Vertical Plate , ASME HTD, Vol. 324, pp. 51-56, 1996. With permission.)... [Pg.463]

The pressure, is thus being measured relative to that which would exist at the same elevation in the stagnant fluid if it were at a uniform temperature of To- The positiv sign in front of the buoyancy term applies to buoyancy-assisted flow and the negative sign again applies to buoyancy-opposed flow. [Pg.467]

The variation of U with Y for various values of GrjIRe is shown in Fig. 9.30. Results are only given in this figure for assisting flow, i.e., for the - sigi on the buoyancy term in Eq. (9.121). [Pg.470]

Velocity profiles in fully developed mixed convective flow in a vertical plane channel. Results are for assisting flow. [Pg.471]

This equation indicates that in assisting flow this shear stress will be zero when ... [Pg.471]

This chapter has been concerned with flows in wb ch the buoyancy forces that arise due to the temperature difference have an influence on the flow and heat transfer values despite the presence of a forced velocity. In extemai flows it was shown that the deviation of the heat transfer rate from that which would exist in purely forced convection was dependent on the ratio of the Grashof number to the square of the Reynolds number. It was also shown that in such flows the Nusselt number can often be expressed in terms of the Nusselt numbers that would exist under the same conditions in purely forced and purely free convective flows. It was also shown that in turbulent flows, the buoyancy forces can affect the turbulence structure as well as the momentum balance and that in turbulent flows the heat transfer rate can be decreased by the buoyancy forces in assisting flows whereas in laminar flows the buoyancy forces essentially always increase the heat transfer rate in assisting flow. Some consideration was also given to the effect of buoyancy forces on internal flows. [Pg.477]

Many different designs for microwave-assisted flow digestion systems have been published [25, 32, 101], which open up new possibilities, primarily in fully automated sample preparation for elemental analysis. [Pg.94]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...