Chemical work

The electrochemical potential is defined as the total work of bringing a species i from vacuum into a phase a and is thus experimentally defined. It.may be divided into a chemical work p , the chemical potential, and the electrostatic work ZiC0 ... [Pg.206]

If the alcohol is required for conductivity or other physico-chemical work and traces of bases are objectionable, these may be removed by redistillation from a little 2 4 6-trinitrobenzoic acid. This acid is selected because it is not esterified by alcohols, consequently no water is introduced into the alcohol. [Pg.168]

Microchemical or ultramicrochemical techniques are used extensively ia chemical studies of actinide elements (16). If extremely small volumes are used, microgram or lesser quantities of material can give relatively high concentrations in solution. Balances of sufficient sensitivity have been developed for quantitative measurements with these minute quantities of material. Since the amounts of material involved are too small to be seen with the unaided eye, the actual chemical work is usually done on the mechanical stage of a microscope, where all of the essential apparatus is in view. Compounds prepared on such a small scale are often identified by x-ray crystallographic methods. [Pg.216]

Only Japan and the United States have significant commercial faciUties for the production of poly(ethylene oxide) resins. In Japan, Meisei Chemical Works Ltd. produces Alkox and Sumitomo Seika Kagaky Co., Ltd., PEO. In the United States, Union Carbide Corp. produces Polyox. Precise figures have not been released on capacities or aimual production. [Pg.343]

Aluminum Acetates" in ECT 1st ed. under "Aluminum Compounds," Vol. 1, pp. 626 —627, "Aluminum Formates" in ECT 1st ed. under "Aluminum Compounds," Vol. 1, pp. 630—632, by Benjamin Toubes, Victor Chemical Works, "Aluminum Acetate" in ECT 2nd ed. under "Aluminum Compounds," Vol. 2, pp. 11—13, by Albert Stewart, MaUinckrodt Chemical Works, "Aluminum Formate" in ECT 2nd ed. under "Aluminum Compounds," Vol. 2, pp. 14—17, by Benjamin Toubes, Victor Chemical Works, a Division of Stauffer Chemical Company, "Aluminum Carboxylates" in ECT 3rd ed. under "Aluminum Compounds," Vol. 2, pp. 202—209, by Glenn H. Warner, Union Carbide Corporation. [Pg.144]

The most thoroughly studied mode of /3-lactam hydrolysis is that catalyzed by the enzyme /3-lactamase (EC 3.5.2.6). The elaboration of this enzyme is one of the three principal ways in which a bacterium can obtain resistance to a /3-lactam antibiotic (see Section 5.11.5.1), and much of the chemical work carried out on the penicillin molecule has been related to attempts to deal with this problem. A discussion of the /3-lactamases is beyond the scope of this work. The reader is referred to (B-79MI51101) for a recent review. [Pg.327]

FIG. 2-1 Vapor pressures of H3PO4 aqueous partial pressure of H2O vapor. Couiiesy of Victor Chemical Works, Stauffer Chemical Company measurements hy W H. Woodstock.)... [Pg.121]

Reciprocating Screens These screens have rnanv applications in chemical work. An eccentric under the screen supplies oscillation, ranging from gyi atoi-v [about 0,05-m (2-in) diameter] at the feed end to reciprocating motion at the discharge end, Freqiiencv is 8 to 10... [Pg.1773]

Obtained from Victor Chemical Works, Chicago, Illinois. [Pg.44]

Small versions of downdraft tables (less than approximately 0.5 m-) are used when small-sized chemical work is to be done on rabies instead of in laboratory-fume hoods (see Fig. 10.37). This includes work with low-momentum source (no initial velocity and near room temperature) such as laboratory animal experiments. [Pg.873]

The downdraft tables used tor small-scale chemical work are only recommended for small operations that generate contaminants near the working surface. The items that are used should not cover too large an area of the exhaust. Covering the surface increases the velocity and subsequently also the... [Pg.875]

For small downdraft tables used for chemical work, a flow rate of 0.28 m s and m- table is used. This gives a mean velocity immediately above the surface of approximately 0.3 m s h This is a very low velocity, which can not capture moving contaminants. When these values are used, a maximum use height of 0.15 m is recommended, which should result in a small leakage from the source to the surrounding. This presumes there is at least 0.1 m of uncovered surface between the worker and the source and that the surface is covered to less than 30%. For these tables the pressure difference is between 50 and 100 Pa, depending on the density of holes. ... [Pg.876]

Comparatively few alterations have been made since 1989 in the structures accepted for well-known alkaloids. A slight but important change has been adopted in the formula of strychnine and contributions to the chemistry of that alkaloid and its associates are still being made, though the formula seems now so well established that Woodward has recently suggested and discussed a scheme for the biogenesis of strychnine on which Robinson has commented favourably. Robinson has also proposed a scheme for the biogenesis of emetine. This involves a modification in the formula of that alkaloid, which is supported by Dewar s interpretation of the results of recent chemical work on emetine by Karrer et al., by Spath and by Pailer. ... [Pg.823]

A chemical works mills Compound A from a feed of Sauter mean size of 6350 im to a material whose size analysis produced ... [Pg.140]

Great Western Inorganics Honeywell Performance P C Lancashue Chemical Works (UK) McGean-Rohco Merck (Geiinany)... [Pg.42]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...