Chemists’ work

Thus, in the area of combinatorial chemistry, many compounds are produced in short time ranges, and their structures have to be confirmed by analytical methods. A high degree of automation is required, which has fueled the development of software that can predict NMR spectra starting from the chemical structure, and that calculates measures of similarity between simulated and experimental spectra. These tools are obviously also of great importance to chemists working with just a few compounds at a time, using NMR spectroscopy for structure confirmation. [Pg.518]

Figure 1.3 shows an outline of the analytical approach along with some important considerations at each step. Three general features of this approach deserve attention. First, steps 1 and 5 provide opportunities for analytical chemists to collaborate with individuals outside the realm of analytical chemistry. In fact, many problems on which analytical chemists work originate in other fields. Second, the analytical approach is not linear, but incorporates a feedback loop consisting of steps 2, 3, and 4, in which the outcome of one step may cause a reevaluation of the other two steps. Finally, the solution to one problem often suggests a new problem. [Pg.5]

In Section lA we indicated that analytical chemistry is more than a collection of qualitative and quantitative methods of analysis. Nevertheless, many problems on which analytical chemists work ultimately involve either a qualitative or quantitative measurement. Other problems may involve characterizing a sample s chemical or physical properties. Finally, many analytical chemists engage in fundamental studies of analytical methods. In this section we briefly discuss each of these four areas of analysis. [Pg.8]

Analytical chemists work to improve the ability of all chemists to make meaningful measurements. Chemists working in medicinal chemistry, clinical chemistry, forensic chemistry, and environmental chemistry, as well as the more traditional areas of chemistry, need better tools for analyzing materials. The need to work with smaller quantities of material, with more complex materials, with processes occurring on shorter time scales, and with species present at lower concentrations challenges analytical... [Pg.9]

Typical problems on which analytical chemists work include qualitative analyses (what is present ), quantitative analyses (how much is present ), characterization analyses (what are the material s chemical and physical properties ), and fundamental analyses (how does this method work and how can it be improved ). [Pg.9]

The evolution (revolution) of capabiUties has dramatically changed the way in which chemists work, and, again, many more people can now perform and analyze many more computations than ever before, at ever diminishing costs. [Pg.93]

Industrial chemists work more with polymers than with any other class of materials. [Pg.611]

Consider the substance hydrogen chloride. This compound has the molecular formula HQ. A chemist working with hydrogen chloride, HQ, must often know the weight of a mole of molecules (the molecular weight). This weight is readily calculated from the atomic weights of the two kinds of atoms, H and Cl ... [Pg.33]

Chemists working with azo dyes use a shorthand designation based on the synthesis by azo coupling. It is characterized by an arrow from the amine used for diazotization (the so-called diazo component) to the coupling component, e. g., for 1.8 sulfanilic acid - 2-naphthol. This designation is especially useful for polyazo dyes (see Zollinger, 1991, p. 109). [Pg.7]

The symbol m is often read molar it is not an SI unit. Note that 1 mol-L 1 is the same as 1 mmol-ml 1. Chemists working with very low concentrations of solutes also report molar concentrations as millimoles per liter (mmol-L-1) and micromoles per liter (pmol-I 1). [Pg.79]

The problem with the Arrhenius definitions is that they are specific to one particular solvent, water. When chemists studied nonaqueous solvents, such as liquid ammonia, they found that a number of substances showed the same pattern of acid-base behavior, but plainly the Arrhenius definitions could not be used. A major advance in our understanding of what it means to be an acid or a base came in 1923, when two chemists working independently, Thomas Lowry in England and Johannes Bronsted in Denmark, came up with the same idea. Their insight was to realize that the key process responsible for the properties of acids and bases was the transfer of a proton (a hydrogen ion) from one substance to another. The Bronsted-Lowry definition of acids and bases is as follows ... [Pg.97]

This polymer has one of the simplest molecular structures ([CH2CH2— ] ) and is at present the largest toimage plastic material, having first been produced commercially in 1939 for use in electrical insulation. There is a difficulty over the nomenclature of this polymer. The lUPAC recommended name for the monomer is ethene, rather than the older ethylene. Hence the lUPAC name for the polymer is poly (ethene). However, this name is almost never used by chemists working with the material throughout this book, therefore, this polymer will be referred to by its more widespread name, poly(ethylene). [Pg.6]

The dream of any bioinorganic chemist working on biological systems is to have a sensitive, selective technique with which it is possi-... [Pg.447]

The process (chemical reaction) by which a chemical product is made, as depicted by an equation, is called synthesis. Working in laboratories, chemists devise new ways to synthesize known chemicals or new chemicals never made before and not found in nature. Synthesis chemists working in industrial laboratories also must find or develop uses for the new chemicals that they synthesize while considering the costs of eventual manufacture. [Pg.11]

This book will complement existing reviews and monographs in this field and will be a source of inspiration for chemists working in various field of chemistry. [Pg.228]

C03-0117. Heart disease causes 37% of the deaths in the United States. However, the death rate from heart disease has dropped significantly in recent years, partly because of the development of new drugs for heart therapy by chemists working in the pharmaceutical industry. One of these drugs is verapamil, used for the treatment of arrhythmia, angina, and h q)ertension. A tablet contains 120.0 mg of verapamil. Determine the following quantities (a) the molar mass of verapamil (b) the number of moles of verapamil in one tablet and (c) the number of nitrogen atoms in one tablet. [Pg.194]

Each chemist working analytically uses (sometimes without any awareness) the analytical process, a scheme (see Figure 1) by which most analytical problems are assessed. The analytical process is a multi-step approach to solving questions by analytical chemistry and includes the following steps ... [Pg.51]

The analytical chemist working on chromatographic procedures should consider... [Pg.26]

These experiments were, however, not completely accepted by some chemists working in the area of prebiotic chemistry these critics were unhappy with some synthetic conditions used, such as the KCN concentrations (0.1-0.2 M at 373 K). They felt that cyanide in such concentrations would have been relatively rapidly hydrolysed at 373 K in addition, CO pressures of 75 atm were considered incommensurate with real conditions in hydrothermal systems. [Pg.203]

Many laboratory syntheses of important structural types of compounds are too long or complex to work well in manufacturing. Chemists working in the process area are thus often engaged in inventing new approaches that use the most modern reactions, in order to develop compact synthetic schemes with small numbers of acceptable steps. The modern reactions that make this possible are being invented by chemists involved in basic discovery and creation, usually in universities. The pressure on industrial process chemists to develop practical schemes for manufacturing important products means that they do not normally have the time for the basic research that can lead to new chemical reactions. [Pg.27]

Ramsay, likewise, viewed himself as a physical chemist working in a borderland, and most of his obituarists would interpret his seminal work on inert gases and his work on transmutation as belonging to physical chemistry. In an unpublished book manuscript on physical chemistry that Travers (in a note on the manuscript in the Sir William Ramsay Papers) dates to around 1893, Ramsay begins ... [Pg.107]

But the institutional borderland (though not an actual laboratory, meeting place, or physical collaboration) at which virtually all of these chemists worked... [Pg.203]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...