Factors for Chemical Kinetics

This problem is related to the question of appropriate electronic degeneracy factors in chemical kinetics. Whereas the general belief is that, at very low gas pressures, only the electronic ground state participates in atom recombination and that, in the liquid phase, at least most of the accessible states are coupled somewhere far out on the reaction coordinate, the transition between these two limits as a function of solvent density is by no means understood. Direct evidence for the participation of different electronic states in iodine geminate recombination in the liquid phase comes from picosecond time-resolved transient absorption experiments in solution [40, 44] that demonstrate the participation of the low-lying, weakly bound iodine A and A states, which is also taken into account in recent mixed classical-quantum molecular d5mamics simulations [42. 43]. [Pg.847]

Since 1 a is only a function of spatial coordinate r, the partial derivative in (19-38) is replaced by a total derivative, and the dimensionless concentration gradient evaluated at the external surface (i.e., ] = 1) is a constant that can be removed from the surface integral in the numerator of the effectiveness factor. In terms of the Hougen-Watson kinetic model and the dimensional scaling factor for chemical reaction that agree with the Langmuir-Hinshelwood mechanism described at the beginning of this chapter ... [Pg.499]

One aspect that teachers recognise as difficult for their students is the relationship between empirical data and mathematical models for chemical kinetics. The monitoring of changes in concentration of a reactant or a product with time may be done continuously in a computer environment since the correspondent changes in some concentration-dependent property may be registered, data may be depicted graphically and equations may be derived from them. Additionally, students may produce hypotheses of how a reaction occurs or of how factors as temperature, for instance, influence the rate of a reaction when the software make possible the control of input values (Andaloro, Donzelli Sperandeo-Mineo, 1991 Hartley, 1988 Sutherland, 1989). The important understanding of the relationships between kinetic data and mechanism of a reaction would then be supported. [Pg.310]

Fig. 1. An example of a two-dimensional valley. Such valley-shaped objective functions are typical for chemical kinetics modeling [8]. This specific example is taken from a study of formaldehyde pyrolysis [3], with yf ia and A2 being pre-exponential factors of the rate coefficients of reactions H + HCO -f M CHjO + M and CH2O -f H - H2 + HCO, respectively.

We will consider two situations that are significant for chemical kinetics. In both cases, the coefficient kg is so small that it does not affect the leading term of the approximation. Therefore, without loss of generality, we assume hereafter that kg = 0. In addition, one of the coefficients of order C (l) can be taken equal to unity by a proper choice of the time normalization factor T. ... [Pg.14]

Kinetic investigations cover a wide range from various viewpoints. Chemical reactions occur in various phases such as the gas phase, in solution using various solvents, at gas-solid, and other interfaces in the liquid and solid states. Many techniques have been employed for studying the rates of these reaction types, and even for following fast reactions. Generally, chemical kinetics relates to tlie studies of the rates at which chemical processes occur, the factors on which these rates depend, and the molecular acts involved in reaction mechanisms. Table 1 shows the wide scope of chemical kinetics, and its relevance to many branches of sciences. [Pg.1119]

Considering the factors shown above and the heterogeneous, transient nature of the mechanical, kinetic, and thermal components, the most favorable time for chemical reaction is during the loading pulse, not during the post-shock thermal-cooling period. [Pg.146]

In processing, it is frequently necessary to separate a mixture into its components and, in a physical process, differences in a particular property are exploited as the basis for the separation process. Thus, fractional distillation depends on differences in volatility. gas absorption on differences in solubility of the gases in a selective absorbent and, similarly, liquid-liquid extraction is based on on the selectivity of an immiscible liquid solvent for one of the constituents. The rate at which the process takes place is dependent both on the driving force (concentration difference) and on the mass transfer resistance. In most of these applications, mass transfer takes place across a phase boundary where the concentrations on either side of the interface are related by the phase equilibrium relationship. Where a chemical reaction takes place during the course of the mass transfer process, the overall transfer rate depends on both the chemical kinetics of the reaction and on the mass transfer resistance, and it is important to understand the relative significance of these two factors in any practical application. [Pg.573]

There are two principal chemical concepts we will cover that are important for studying the natural environment. The first is thermodynamics, which describes whether a system is at equilibrium or if it can spontaneously change by undergoing chemical reaction. We review the main first principles and extend the discussion to electrochemistry. The second main concept is how fast chemical reactions take place if they start. This study of the rate of chemical change is called chemical kinetics. We examine selected natural systems in which the rate of change helps determine the state of the system. Finally, we briefly go over some natural examples where both thermodynamic and kinetic factors are important. This brief chapter cannot provide the depth of treatment found in a textbook fully devoted to these physical chemical subjects. Those who wish a more detailed discussion of these concepts might turn to one of the following texts Atkins (1994), Levine (1995), Alberty and Silbey (1997). [Pg.85]

Notice that the word spontaneous has a different meaning in thermodynamics than it does in everyday speech. Ordinarily, spontaneous refers to an event that takes place without any effort or premeditation. For example, a crowd cheers spontaneously for an outstanding performance. In thermodynamics, spontaneous refers only to the natural direction of a process, without regard to whether it occurs rapidly and easily. Chemical kinetics, which we introduce in Chapter 15, describes the factors that determine the speeds of chemical reactions. Thermodynamic spontaneity refers to the direction that a process will take if left alone and given enough time. [Pg.973]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...