Risk assessment failure rate data

In this study detailed fault trees with probability and failure rate calculations were generated for the events (1) Fatality due to Explosion, Fire, Toxic Release or Asphyxiation at the Process Development Unit (PDU) Coal Gasification Process and (2) Loss of Availability of the PDU. The fault trees for the PDU were synthesized by Design Sciences, Inc., and then subjected to multiple reviews by Combustion Engineering. The steps involved in hazard identification and evaluation, fault tree generation, probability assessment, and design alteration are presented in the main body of this report. The fault trees, cut sets, failure rate data and unavailability calculations are included as attachments to this report. Although both safety and reliability trees have been constructed for the PDU, the verification and analysis of these trees were not completed as a result of the curtailment of the demonstration plant project. Certain items not completed for the PDU risk and reliability assessment are listed. [Pg.50]

The procedure described by Figure 10-1 is frequently abbreviated based on circumstances. If failure rate data on the applicable equipment are not available, then risk assessment procedures cannot be fully applied. Most plant sites (and even subunits within a plant) modify the procedure to fit their particular situation. [Pg.431]

It is important to distinguish the types of time-related and demand-related equipment failure rate data that can be found and used in afire risk assessment. Basically, four types of data and corresponding data sources provide both time-related and demand-related failure data as shown in Table 6-3 and discussed in the following sections. [Pg.108]

Increasing attention is being given to developing methods to predict failure rate data for process equipment and systems. Such methods are beginning to appear in published literature. These methods include correlations, factored estimation procedures, and analogies to predict equipment failure rates. They are desirable because they offer efficient means of providing equipment failure rate data for risk assessments, and they can be conveniently incorporated into computer software. [Pg.110]

The primary purpose of each update OHA is to identify, analyze, and control hazards associated with the operation of the end product. In order to do so properly, baseline data (risk assessment and acceptance criteria, estimated failure rates, exposure, and the like) must be reviewed and revised as indicated by the most current information available. [Pg.99]

EPA concluded that the dataset referenced by one commenter that consists of dust samples collected for risk assessment purposes in 41 states is not informative because there was no information on renovation activity collected with these dust samples. With respect to the Maryland renovation study, 96.7% is an overstatement. The author who conducted the analysis stated that when the maximum test values are examined rather than the mean, 9.8% of the Maryland sample and 12.5% of the national sample of properties with EBP surpassed at least one of the hazard thresholds of 40 ig/sf for floors and 250 ig/ sf for sills. One of the study s exhibits showed a fairly sizable percentage of the lead tests exceeded the clearance thresholds. The failure rates were about 20% lower for Maryland than for the national LBP sample. However, even for Maryland, nearly one in ten apartments would fail the hazard test. Thus, even if these were the only data available, it would not support the conclusion that visual clearance is effective. [Pg.211]

In order to analyse the risk of lack of water supply in the aspect of water consumer, caused by the failures on distribution network in the first instance the analysis of the intensity of distribution network was made. In the failure analysis and assessment the failure rate index, X, for water pipes, was used. The values of the failure rate index for distribution pipes were determined on the basis of the formulas available in the hterature (Rak 2009, Tchorzewska-Cieslak 2011) and operational data. The results of the analysis and failure assessment for years 2005 to 2012 were presented in Table 7 and Figure 4. [Pg.501]

HSE Health and Safety Executive. Failure rate and event data for use within land use planning risk assessments. Document ID HSE PCAG chp 6 K Version 12—28/06/12. Available at http //www.hse.gov.uk. [Pg.1708]

FRED 2012 Failure Rate and Event Data for use within Land Use Planning Risk Assessments updated 28-6-2012 http //www.hse.gov.uk/landuseplanning/failure-rates.pdf... [Pg.1847]

Acute pancreatitis is usually a self-limiting disease, which regresses spontaneously without further complications. However, in about 20% of cases it leads to organ failure and/or local complications and is associated with high morbidity and mortality rates (B15). Therefore, numerous attempts have been made to predict early the severe course of acute pancreatitis and to assess the possibility of complications. Objective identification of the risk of complications or death is essential for selection of those patients who should be hospitalized in the intensive care unit (ICU) and be subjected to more expensive and aggressive investigations. Moreover, it also permits interinstitutional comparison of data stratified for severity at admission and at the time of therapy. [Pg.57]

Expert judgment is a key source of data especially in relation to the failure process and the quantification of epistemic uncertainties. For example, we need to specify and to determine the values of target variables, such as the baseline probability and risk reduction proportions, which we assume are fixed. The shock rate, wear-out parameters and onset of premature wear-out also require to be assessed. For the epistemically uncertain parameters, such as the onset of aging, we use the whole uncertainty distribution as assessed by experts. [Pg.807]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...