Film forming processing separation

Vecchio C, Fabiani F, Gazzaniga A. Use of colloidal silica as a separating agent in film forming processes performed with aqueous dispersion of acrylic resins. Drug Dev Ind Pharm 1995 21(15) 1781-1787. [Pg.559]

Figure 18.5 Rate-limiting processes in film formation (a) separation of film formation into water ev oration and particle deformation and compaction components, (b) effect of drying conditions on film formation. Bold dashed lines reference rates of processes in (a). Bold solid lines boundary of the limiting film-formation processes at low and high temperature. Light dashed lines possible shifts of film-forming process rates from the reference rates by, for example, plasticization of the latex particles and/or slowing of the water evaporation rate. Points A, B, C and D represent the MFTs resulting from these variations in conditions. (Reproduced with permission from Sperry et al. [53].)...

Furthermore, AFM (Atomic Force Microscopy) studies have shown that during the film-forming process many conventional surfactants phase separate from the binder. When the surfactant has phase separated, the water flux may carry it to the film surface. Alternatively, it may accumulate in the interstices between... [Pg.109]

In contrast to a conventional p-n-junction-type solar cell, the mechanism of the DSSC does not involve a charge-recombination process between electrons and holes because electrons are injected from the dye photosensitizers into the semiconductor, and holes are not formed in the valence band of the semiconductor. In addition, electron transport takes place in the Ti02 film, which is separated from the photon absorption sites (i.e., the photosensitizers) thus, effective charge separation is expected. This photon-to-current conversion mechanism of the DSSC is similar to that for photosynthesis in nature, where chlorophyll functions as the photosensitizer and electron transport occurs in the membrane. [Pg.134]

The emulsion of a typical color film has three silver-bromide layers separately sensitized by suitable dyes to blue, green, and red light (Figure 28-11). When processed (Section 28-6C), the color formed in each layer is complementary to the color to which the layer is sensitive. Thus, if unexposed film is processed, intense yellow, magenta, and cyan colors are respectively formed in the blue-, green-, and red-sensitive layers. Then, when white light strikes this processed... [Pg.1410]

In conclusion we emphasize that the final chemical composition of the surface films covering Li electrodes in solutions is the result of a delicate balance between several competing reduction processes of solvent, salt anion, and contaminants. In this section we emphasize the role of salt reduction processes. However, each solution has to be studied separately since the above balance is determined by factors such as salt concentration, the nature of the solvent, contamination level, etc., all of which differ from system to system. Table 4 presents element analysis by XPS of surface films formed on freshly prepared Li electrodes in several solutions. It demonstrates how the impact of salt reduction on the Li surface chemistry depends on the solution composition and the storage time. (The atomic percentage of fluorine on the surface is a good measure for the impact of the salt.)... [Pg.339]

In order to find the domain of LCVD, it is necessary to compare various vacuum deposition processes chemical vapor deposition (CVD), physical vapor deposition (PVD), plasma chemical vapor deposition (PCVD), plasma-assisted CVD (PACVD), plasma-enhanced CVD (PECVD), and plasma polymerization (PP). All of these terms refer to methods or processes that yield the deposition of materials in a thin-film form in vacuum. There is no clear definition for these terms that can be used to separate processes that are represented by these terminologies. All involve the starting material in vapor phase and the product in the solid state. [Pg.7]

Emulsions may contain not just oil and water, but also solid particles and even gas. In the large mining and processing operations applied to Canadian oil sands, bitumen is separated from the sand matrix in large tumblers as an emulsion of oil dispersed in water, and then further separated from the tumbler slurry by a flotation process. The product of the flotation process is bituminous froth, an emulsion that may be either water (and air) dispersed in the oil (primary flotation) or the reverse, oil (and air) dispersed in water (secondary flotation). In either case, the emulsions must be broken and the water removed before the bitumen can be upgraded to synthetic crude oil, but the presence of solid particles and film-forming components from the bitumen can make this removal step very difficult. [Pg.4]

The transistor film is then mechanically processed by a numerically controlled (NC) cutting plotter or drilling machine to form the net-shaped structures, as shown in Figure 6.3.8. In a similar way, a pressure-sensitive rubber sheet and a copper electrode suspended by a polyimide film are cut separately to form net-shaped structures. These two films are laminated on the top of the transistor fihn to complete the pressure sensor network. The periodicity is 4 mm, and the width of the struts is 0.3-0.5 mm. [Pg.537]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...