Films dichroic

The linear dichroism measurement demonstrated that MOPPV chains formed the planar orientation chains in the LB films dichroic ratio Ap/As... [Pg.327]

Using this strategy, constmction of multilayer films of - O. fim thickness by self-assembly of methyl 23-ttichlorosilyltticosanoate (MTST) on siUcon substrates has been demonstrated (Fig. 9) (165). The linear relationship between the film thickness and the layer number showed a slope of 3.5 nm /layer. Filipsometry data, absorbance intensities, and dichroic ratios for the multilayers all suggest that the samples were composed of distinct monolayers. However, ir data indicated that there maybe more tilting or disordering of the alkyl chains in the seven-layer sample than for the monolayer samples. [Pg.539]

In order to develop the dyes for these fields, characteristics of known dyes have been re-examined, and some anthraquinone dyes have been found usable. One example of use is in thermal-transfer recording where the sublimation properties of disperse dyes are appHed. Anthraquinone compounds have also been found to be usehil dichroic dyes for guest-host Hquid crystal displays when the substituents are properly selected to have high order parameters. These dichroic dyes can be used for polarizer films of LCD systems as well. Anthraquinone derivatives that absorb in the near-infrared region have also been discovered, which may be appHcable in semiconductor laser recording. [Pg.336]

Normal incidence transmission IRLD measurements are used to study thin films (typically 100 pm thickness and less, depending on the molar extinction coefficient of the bands) with in-plane uniaxial orientation. Two spectra are recorded sequentially with the radiation polarized parallel (p) and perpendicular (s) to the principal (machine) direction of the sample. The order parameter of the transition moment of the studied vibration is calculated from either the dichroic ratio (R — Ap/As) or the dichroic difference (AA = Ap—As) as ... [Pg.307]

The parameters K1/ K2/ and K3 are defined by the refractive indices of the crystal and sample and by the incidence angle [32]. If the sample has uniaxial symmetry, only two polarized spectra are necessary to characterize the orientation. If the optical axis is along the plane of the sample, such as for stretched polymer films, only the two s-polarized spectra are needed to determine kz and kx. These are then used to calculate a dichroic ratio or a P2) value with Equation (25) (replacing absorbance with absorption index). In contrast, a uniaxial sample with its optical axis perpendicular to the crystal surface requires the acquisition of spectra with both p- and s-polarizations, but the Z- and X-axes are now equivalent. This approach was used, through dichroic ratio measurements, to monitor the orientation of polymer chains at various depths during the drying of latex [33]. This type of symmetry is often encountered in non-polymeric samples, for instance, in ultrathin films of lipids or self-assembled monolayers. [Pg.310]

The out-of-plane orientation of chromophores can be more easily controlled in LB films as compared with the in-plane orientation. Many chromophores are known to show anisotropic orientation in the surface normal direction. The molecular structure of chromophores and their position in amphiphile molecules, the surface pressure, the subphase conditions are among those affect their out-of-plane orientation. The out-of-plane orientation has been studied by dichroic ratio at 45° incidence, absorbance ratio at normal and 45° incidence, and incident angle dependence of p-polarized absorption [3,4,27,33-41]. The evaluation of the out-of-plane orientation in LB films is given below using amphipathic porphyrin (AMP) as an example [5,10,12]. [Pg.262]

Further, planar orientation of PPV chains in the film plane was demonstrated from the linear dichroism dichroic ratio Ap/As decreased from 2.1 to 1.2 when the incident angle of polarized light increased from 0° to 45°, where Ap and As... [Pg.326]

Most of the LC polymer systems discussed so far contain the LC moiety incorporated in the polymer main chain. One of the few examples of polarized emission of light using a side-chain LC system was reported by Chang et al. [107]. A polyacrylate was used as the polymer backbone. The nematic LC side-chains consisted of ethyl- and propyl-substituted bis-tolan units. When deposited on a rubbed PEDOT film, polarized EL dichroic ratios were reported to be around 6. [Pg.468]

When a polarized spectrum of the film was taken in the dry state, a small dichroic ratio was observed (A L/A// = 1.3, see Fig. 9c). This is due to the slant structures of base pairs and intercalated dyes to the axis of the strands, since the DNA strands were confirmed to be aligned along the stretching direction even in the dry film (see Fig. 7c). These changes of polarized absorption spectra dependent on water moisture were reversible at least 10 times. [Pg.66]

IR spectroscopy is not only useful for determining the chemical constitution of polymers. It additionally provides profound information on chain orientation and on the orientation of attached lateral substituents of polymers. In this case, polarized IR radiation is applied which is only absorbed by an IR-active bond if the plane in which the electrical field vector E of the IR beam oscillates is parallel to the transition dipole moment p of the vibration to be excited. If, on the other hand, the transition dipole moment p is perpendicular to the electrical field vector E of the IR beam no absorption is observed. Using this effect, the degree of orientation of a polymer sample (film, fiber) can be estimated by comparing the intensity at maximum /(11) and at minimum I ) absorption, i.e., the dichroic ratio. [Pg.84]

The dichroic properties of the Li modiEed montmorillonite were followed by orientation of thin films (0-45°) in the IR beam (FTIR Brucker IFS 88). The cationic exchange capacity (CEC) of the samples calcined at 400°C was evaluated. [Pg.98]

Linear-dichroic spectra of SA monolayers prepared from mixtures of OTS and a cyanine-dye surfactant established the absence of dimerization and the orientation of the chromophore parallel to the substrate [183]. In contrast, the same cyanine dye underwent sandwich-type dimer formation in LB films and had its chromophore oriented perpendicular to the water surface [192]. These results highlight an important difference between LB and SA monolayers. Parameters which determine monolayer formation on an aqueous subphase are also responsible for the orientation and organization of the surfactants therein. Furthermore, the configuration of the surfactants is retained regardless of the structure of the substrate to which the floating monolayer was subsequently transferred to by the LB technique. Conversely, in SA monolayers, surfactant organization is primarily dependent upon the nature of the substrate [183]. [Pg.38]

LB films prepared from stearate ions 20-and 70-A a-Fe203 particles were incorporated between the headgroups of LB films Molecular orientation and structure was investigated by FTIR absorption and linear dichroic measurements 124... [Pg.218]

A closely related phenomenon induced by linearly polarized light was found independently by Gibbons et al., who employed a polyimide (PI) film doped with azobenzene molecules as a dichroic dye and showed that the direction of homogeneous... [Pg.382]

In order to evaluate quantitatively the orientation of vibrational modes from the dichroic ratio in molecular films, we assume a uniaxial distribution of transition dipole moments in respect to the surface normal, (z-axis in Figure 1). This assumption is reasonable for a crystalline-like, regularly ordered monolayer assembly. An alternative, although more complex model is to assume uniaxial symmetry of transition dipole moments about the molecular axis, which itself is tilted (and uniaxially symmetric) with respect to the z-axis. As monolayers become more liquid-like, this may become a progressively more valid model (8,9). We define < > as the angle between the transition dipole moment M and the surface normal (note that 0° electric field of the evenescent wave (2,10), in the ATR experiment are given by equations 3-5 (8). [Pg.147]

The ATR spectra of the transferred monolayer may also be used to calculate the orientation distribution of the hydrocarbon drains in the transferred film. In this case, the dichroic analysis of the polarized ATR spectra proceeds from well-known principles a detailed analysis has been presented elsewhere (17). [Pg.203]

NOTE This formula may cause dichroic fog on some modern emulsion films. Testing is advised. [Pg.208]

If an even finer-grained effect is desired, with an inevitable loss in film speed, increase the acid and extend the development time. This would also increase the chance of dichroic fog. [Pg.240]

Figure 1.9. The optical parametric amplifier (OPA). BS, beam splitter TFP, thin-film polarizer HWP, half-wave plate IMP, dichroic beam splitter or long wave pass filter F,...

Fig. 22(b) shows polarized visible absorption spectra of mixed LB films of MS-C2o binary and MS-C20-AL18 ternary systems prepared by using an aqueous subphase containing Cd2+ ions, where the ratio in the mixed system is [MS] [C20] [AL18] = l 2 x (x — 0 and 1) [77-84]. The thick and thin lines in Fig. 22(b) refer to the spectra, Atl and A , measured by linearly polarized light with the electric vector parallel and perpendicular to the dipping direction of the substrate, respectively. For x = 0, a sharp absorption peak is observed at 590 nm, which is red-shifted from the MS monomer peak at around 540 nm. The dichroic ratio R of the 590 nm band is R> 1, where R is defined as A /A . For x= 1.0, on the other hand, a sharp blue-shifted band with R< 1 appears at 505 nm. Fig. 22(c) refers to the cases of the corresponding binary and ternary systems fabricated under the subphase without the Cd2+ ions [84], Unlike the results in Fig. 22(b), remarkably red- and blue-shifted bands are not observed... [Pg.341]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...