Fluid systems dispersion

We discuss classical non-ideal liquids before treating solids. The strongly interacting fluid systems of interest are hard spheres characterized by their harsh repulsions, atoms and molecules with dispersion interactions responsible for the liquid-vapour transitions of the rare gases, ionic systems including strong and weak electrolytes, simple and not quite so simple polar fluids like water. The solid phase systems discussed are ferroniagnets and alloys. [Pg.437]

When the problem is to disrupt Ughtly bonded clusters or agglomerates, a new aspect of fine grinding enters. This may be iUustrated by the breakdown of pigments to incorporate them in liquid vehicles in the making of paints, and the disruption of biological cells to release soluble produces. Purees, food pastes, pulps, and the like are processed by this type of mill. Dispersion is also associated with the formation of emulsions which are basically two-fluid systems. Syrups, sauces, milk, ointments, creams, lotions, and asphalt and water-paint emulsions are in this categoiy. [Pg.1863]

Popular methods for mutual diffusion measurements in fluid systems are the Taylor dispersion method and interferometric methods, such as Digital Image Holography [13, 14]. [Pg.165]

Dispersed Noninhibited Systems. Drilling fluid systems typically used to drill the upper hole sections are described as dispersed noninhibited systems. They would typically be formulated with freshwater and can often derive many of their properties from dispersed drilled solids or bentonite. They would not normally be weighted to above 12 Ib/gal and the temperature limitation would be in the range of 176-194°F. The flow properties are controlled by a deflocculant, or thinner, and the fluid loss is controlled by the addition of bentonite and low viscosity CMC derivatives. [Pg.666]

Dispersed Inhibited Systems. Dispersed inhibitive fluids attempt to combine the use of dispersed clays and deflocculants to derive the fundamental properties of viscosity and fluid loss with other features that will limit or inhibit the hydration of the formation and cuttings. It will be realized these functions are in opposition therefore the ability of these systems to provide a high level of shale inhibition is limited. However, they have achieved a high level of success and in... [Pg.667]

Grace, H. P., Dispersion phenomena in high viscosity immiscible fluid systems and application of static mixers as dispersion devices in such systems. 3rd Eng. Found. Conf. Mixing, Andover, N. H. Republished in Chem. Eng. Commun. 14, 225-227 (1982). [Pg.200]

The CD model was first proposed by Curl (1963) to describe coalescence and breakage of a dispersed two-fluid system. In each mixing event, two fluid particles with distinct compositions first coalesce and then disperse with identical compositions.75 Written in terms of the two compositions (f>A and [Pg.292]

H.P. Grace Dispersion Phenomena in High Viscosity Immiscible Fluid Systems and Application of Static Mixers as Dispersion Devices in Such Systems. Chem. Eng. Commun 14, 225 (1982). [Pg.49]

Combine first five ingredients with intensive agitation until thoroughly dispersed. When (6) is added, the fluid system will change in a few minutes to a soft paste. [Pg.152]

In the process, a residuum is desulfurized and the nonvolatile fraction from the hydrodesulfurizer is charged to the residuum fluid catalytic cracking unit. The reaction system is an external vertical riser terminating in a closed cyclone system. Dispersion steam in amounts higher than that used for gas oils is used to assist in the vaporization of any volatile constituents of heavy feedstocks. [Pg.330]

System with random fluxes is defined as the nonequilibrium system where the fluxes of substance, heat, etc. change randomly. One can cite numerous examples of such systems turbulent gas-liquid systems with intensive heat/mass transfer, turbulent fluids containing dispersed solids, etc. In the case of pore formation, such situation is realized when the heat fluxes change randomly because of air fluidization or mechanical mixing. All macroscopic measured parameters of stationary turbulent flows, like their pressure, temperature, excess (free) energy, entropy, etc. do not change with time, while their values and directions in different spots of the flows can vary significantly. [Pg.45]

For mechanistic studies, ambient pressure experiments on emulsions and foams often offer significant experimental advantages over high-pressure experiments. However, high-pressure measurements are also needed since the phase behavior, physical properties of the fluids, and dispersion flow may all depend on pressure. Experiments under laboratory conditions that closely match reservoir conditions are particularly important in the design of projects for specific fields. Chapter 19, by Lee and Heller, describes steady-state flow experiments on CO2 systems at pressures typical of those used in miscible flooding. The following chapter, by Patton and Holbrook,... [Pg.22]

Measurements of supercritical ethane density versus the AOT concentration shown in Figure 4 (T = 37 C, P = 250 bar) indicate that the properties of the supercritical continuous phase resemble those of the pure fluid. The dispersed micelle phase does not appear to increase the critical temperature or critical pressure of the binary solution to the point of inducing a phase change in the system. There is a small increase in density as surfactant is added to the system which confirms the visual observation that a second liquid phase of much higher density is not formed. [Pg.105]

The diffusion path method has been used to interpret nonequilibrium phenomena in metallurgical and ceramic systems (10-11) and to explain diffusion-related spontaneous emulsification in simple ternary fluid systems having no surfactants (12). It has recently been applied to surfactant systems such as those studied here including the necessary extension to incorporate initial mixtures which are stable dispersions instead of single thermodynamic phases (13). The details of these calculations will be reported elsewhere. Here we simply present a series of phase diagrams to show that the observed number and type of intermediate phases formed and the occurrence of spontaneous emulsification in these systems can be predicted by the use of diffusion paths. [Pg.195]

The term coalescence generally describes the prcxiess in which the primary produced, mostly very small gas bubbles or drops merge together into larger, stable ones. In fact, in fluid G/1 and L/L material systems, dispersion and merging together (coalescence) of the dispersed phase takes place constantly and the so-called stable bubble (droplet) size, under turbulent flow conditions, merely represents the the steady-state situation. [Pg.165]

The mesoscale models for momentum transfer between phases differ quite substantially depending on the multiphase system under investigation, and different semi-empirical relationships have been developed for different systems. Since the nature of the disperse phase is particularly important, the available mesoscale models are generally divided into those valid for fluid-fluid and those valid for fluid-solid systems. The main difference is that in fluid-fluid systems the elements of the disperse phase are deformable particles (i.e. bubbles or droplets), whereas in fluid-solid systems the disperse phase is constituted by particles of constant shape. Typical fluid-fluid systems for which the mesoscale models reported below apply are gas-liquid, liquid-liquid, and liquid-gas systems. The mesoscale models reported for fluid-solid systems are valid both for gas-solid and for liquid-solid systems. As a general rule, the mesoscale model for Afp should be derived starting from a single-particle momentum balance ... [Pg.161]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...