Gas-Solid-Liquid Mixing

Multi-phase mixing is often seen in industries. In general, the distribution of not only the dispersed phase but also the continuous phase depends on the local position in the equipment in the case of a multi-phase operation such as gas-liquid mixing system, liquid-liquid mixing system, solid-liquid mixing system, and gas-liquid-solid mixing system. In order to evaluate the mixing state in such systems, both the dispersed phase and continuous phase should be considered. [Pg.74]

Low feed rates are suitable for trickle bed reactors where for gas-liquid-solid mixing, the gas and the liquid are fed into the top of the reactor. This gives long gas residence times but short liquid residence times. Such a configuration is often used in hydrogenation reactions. When the gas-liquid is fed into the bottom of the reactor, it is known as a bubble reactor. Here the gas residence times are short but the liquid residence times are relatively long. This is commonly used in oxidation reactions. Heat transfer can be a major problem with both trickle and bubble reactors and in such cases a slurry bubble column reactor can be employed. [Pg.8]

Liquid residence-time distributions in mechanically stirred gas-liquid-solid operations have apparently not been studied as such. It seems a safe assumption that these systems under normal operating conditions may be considered as perfectly mixed vessels. Van de Vusse (V3) have discussed some aspects of liquid flow in stirred slurry reactors. [Pg.123]

Semibatch reactors are often used to mn highly exothermic reactions isothermally, to run gas-liquid(-solid) processes isobarically, and to prevent dangerous accumulation of some reactants in the reaction mixture. Contrary to batch of)eration, temperature and pressure in semibatch reactors can be varied independently. The liquid reaction mixture can be considered as ideally mixed, while it is assumed that the introduced gas flows up like a piston (certainly this is not entirely true). Kinetic modelling of semibatch experiments is as difficult as that of batch, non-isotherma experiments. [Pg.295]

This reaction is an example of a heterogeneous reaction with a solid catalyst with one reactant principally in solution and another in the gas phase the gas-liquid-solid mixture has to be mixed thoroughly to promote conversion (see Chapter 5 for more detailed consideration of multiphase reactions). Compared with the examples above, the measurement of the hydrogen uptake delivers an additional signal, which can also be used for the determination of reaction parameters. [Pg.222]

Gas-liquid bubble columns and gas-liquid-solid slurry bubble columns are widely used in the chemical and petrochemical industries for processes such as methanol synthesis, coal liquefaction, Fischer-Tropsch synthesis and separation methods such as solvent extraction and particle/gas flotation. The hydrodynamic behavior of gas-liquid bubble columns and gas-liquid-solid slurry bubble columns are of great importance for the design and scale-up of reactors. Although the hydrodynamics of the bubble and slurry bubble columns has been a subject of intensive research through experiments and computations, the flow structure quantification of complex multi-phase flows are still not well understood, especially in the three-dimensional region. In bubble and slurry bubble columns, the presence of gas bubbles plays an important role to induce appreciable liquid/solids mixing as well as mass transfer. The flows within these systems are divided into two... [Pg.191]

The hydrodynamic parameters that are required for stirred tank design and analysis include phase holdups (gas, liquid, and solid) volumetric gas-liquid mass-transfer coefficient liquid-solid mass-transfer coefficient liquid, gas, and solid mixing and heat-transfer coefficients. The hydrodynamics are driven primarily by the stirrer power input and the stirrer geometry/type, and not by the gas flow. Hence, additional parameters include the power input of the stirrer and the pumping flow rate of the stirrer. [Pg.53]

Wiedmann et al. (1980) have compared the mixing of nonaerated liquids, aerated liquids, and slurries in a turbulent flow. They found that the torque required for stirred, aerated liquids is lower than that for nonaerated stirred liquids because of the decrease in the density of the gas-liquid mixture. The concentration distribution of the particles in aerated suspension becomes more uniform with increasing impeller speed, whereby the torque is higher than that for aerated liquids but lower than that for nonaerated slurries. For gas-liquid-solid systems, very limited data on dispersion of solids and gas phase are available, and further studies are necessary with different designs and for systems with different physical properties. The available literature has been reviewed by Stiegel et al. (1978), Shah et al. (1982), and Shah and Sharma (1986). [Pg.52]

Internal recycle reactors are designed so that the relative velocity between the catalyst and the fluid phase is increased without increasing the overall feed and outlet flow rates. This facilitates the interphase heat and mass transfer rates. A typical internal flow recycle stirred reactor design proposed by Berty (1974, 1979) is shown in Fig. 18. This type of reactor is ideally suited for laboratory kinetic studies. The reactor, however, works better at higher pressure than at lower pressure. The other types of internal recycle reactors that can be effectively used for gas-liquid-solid reactions are those with a fixed bed of catalyst in a basket placed at the wall or at the center. Brown (1969) showed that imperfect mixing and heat and mass transfer effects are absent above a stirrer speed of about 2,000 rpm. Some important features of internal recycle reactors are listed in Table XII. The information on gas-liquid and liquid-solid mass transfer coefficients in these reactors is rather limited, and more work in this area is necessary. [Pg.75]

In previous sections, we examined the design parameters for gas-liquid, gas-solid, liquid-liquid, gas-liquid-solid, biological polymerization, and special types of mechanically agitated reactors. In this section we present a brief review on available techniques for the measurement of various mixing and transport parameters for a mechanically agitated vessel. Both physical and chemical techniques are examined. [Pg.169]

An appropriate design and model of a gas-liquid-solid reactor requires the estimation of various transport (momentum, mass, and heat), kinetic, and mixing parameters. Specifically, the following parameters are needed. [Pg.6]

This type of reactor (see Fig. 5-3) can be used for both gas-liquid-solid catalytic i and noncatalytic reactions. The reactor is well mixed and it can be operated l isothermally. The construction of the reactor is straightforward and inexpensive ... [Pg.153]

Better mixing is obtained. A wider range of particle sizes can be used and better gas liquid-solid contact is possible. [Pg.160]

In many multiphase (gas-liquid, gas-solid, liquid-liquid and gas-liquid-solid) contactors, a large degree of circulation of both discrete and continuous phases occurs. This circulation causes a good degree of mixing and enhances heat and mass transfer between fluid and walls. The degree of circulation depends on a number of parameters such as the size of equipment, the nature of the phases involved, velocities of various phases, nature of the internals within the equipment and many others. [Pg.243]

Typically, this additional biological step is carried out in a pachuca, a cone-bottomed column familiar to the mining industry. Ground or milled ore, mixed with the aqueous bacterial solution, is introduced into the top of the column, and air is injected at the base. The injected air serves a number of functions it maintains the solid in suspension, it mixes the solid with liquid— giving a three-phase gas/liquid/ solid system—and it provides the oxygen and carbon dioxide required by the bacteria. The bacteria also require a feed of nitrogen and phosphorous, which can be added to the colunm if they are not indigenous to the ore. [Pg.81]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...