Instruments, design

2Generally the y-axis is left as an amplification of differential thermocouple voltage, showing exothermic and endothermic trends, where no effort is made to convert the abscissa values into temperatures. [Pg.36]

If there is good communication between the heating elements and the sample or reference thermocouple junctions, then the control system can make its power adjustments based on one of those temperatures. If there is substantial insulation between these locations, which may be necessary for heat flow uniformity to both sample and reference or to permit the introduction of special gases, then a separate control thermocouple is used which is placed near the furnace windings. [Pg.37]

The sample and reference chambers are heated equally into a temperature regime in which a transformation takes place within the sample. As the sample temperature infinitesimally deviates from the reference temperature, the device detects it [Pg.38]

This DSC has two control cycle portions. One portion strives to maintain the null balance between sample and reference, while the other strives to keep the average of the sample and reference temperature at the setpoint. These processes switch back and forth quickly so as to maintain both simultaneously. [Pg.39]

Some confusion abounds with respect to instruments which [Pg.39]

Instrument Designs for Infrared Absorption The simplest instrument for IR absorption spectroscopy is a filter photometer similar to that shown in Figure 10.24 for UV/Vis absorption. These instruments have the advantage of portability and typically are used as dedicated analyzers for gases such as ITCN and CO. [Pg.393]

Molecular Phosphorescence Instrumentation for molecular phosphorescence must discriminate between phosphorescence and fluorescence. Since the lifetime for fluorescence is much shorter than that for phosphorescence, discrimination is easily achieved by incorporating a delay between exciting and measuring phosphorescent emission. A typical instrumental design is shown in Figure 10.46. As shown... [Pg.428]

Time, Cost, and Equipment Automated chemical kinetic methods of analysis provide a rapid means for analyzing samples, with throughputs ranging from several hundred to several thousand determinations per hour. The initial start-up costs, however, may be fairly high because an automated analysis requires a dedicated instrument designed to meet the specific needs of the analysis. When handled manually, chemical kinetic methods can be accomplished using equipment and instrumentation routinely available in most laboratories. Sample throughput, however, is much lower than with automated methods. [Pg.642]

The Poiseuille equation provides a method for measuring 77 by observing the time required for a liquid to flow through a capillary. The apparatus shown in Fig. 9.6 is an example of one of many different instruments designed to use this relationship. In such an experiment the time required for the meniscus to drop... [Pg.602]

The analytical range is determined by the instrumental design. For this method, a portion of the analytical range is selected by choosing the span of the monitoring system. The span of the monitoring system is selected such that the pollutant gas concentration equivalent to the emission standard is not less than 30 percent of the span. If at any time during a rim the measured gas concentration exceeds the span, the rim is considered invahd. [Pg.2200]

The main principles of instrument design are summarized in Table 10.23. In filtration, e.g. for gravimetric analysis, selection of filter material (Table 10.22) requires careful consideration in terms of application, strength, collection efficiency, compatibility with pump, water uptake, etc. Humidity-controlled balance rooms, iTiicrobalances and careful handling techniques may be required. [Pg.354]

As the process moves from the process development stage to the design and construction stage the chemistry, unit operations, and type of equipment have been set. The design and construction stage needs to focus primarily on equipment specifications, piping and instrumentation design, installation details, and layout for an inherently safer installation. [Pg.72]

For final design horsepower and equipment selection, the usual practice is to submit the refrigeration load and utility conditions/requirements to a reputable refrigerant system designer/manufacturer and obtain a warranted system with equipment and instrumentation design and specifications including the important materials of construction. Always request detailed operating instructions/controls and utility quantity requirements. [Pg.353]

Thermography is a predictive maintenance technique that can be used to monitor the condition of plant machinery, structures and systems. It uses instrumentation designed to monitor the emission of infrared energy, i.e. temperature, to determine their operating condition. By detecting thermal anomalies, i.e. areas that are hotter or colder than they should be, an experienced surveyor can locate and define incipient problems within the plant. [Pg.799]

Whilst nothing can improve upon the disadvantage of low molar absorption coefficients, instrumental designs and improvements with ratio recording and FT-IR instruments have virtually overcome the accuracy and instrumental limitations referred to in (b) and (c) above. As a result, quantitative infrared procedures are now much more widely used and are frequently applied in quality control and materials investigations. Applications fall into several distinct groups ... [Pg.752]

Subsequently, a wide array of developments in TIMS methods for uranium-series measurement occurred during the past decade including initiation of methods for measurement of long-lived radium (Volpe et al. 1991 Cohen and O Nions 1991) and protactinium isotopes (Pickett et al. 1994 Bourdon et al. 1999), development of improved sources or ionization methods for TIMS analysis, and introduction of commercially available multi-collector TIMS instruments designed specifically for uranium and thorium isotopic measurement. [Pg.32]

High speed separations, particularly with narrow-bore HCOT columns of 100 aicroneters or less, places special demands upon the instrument design [131,134,148-150]. The gas chromatograph... [Pg.547]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...