Oven, ovens

In order to answer these questions, the kinetic and network structure models were used in conjunction with a nonlinear least squares optimization program (SIMPLEX) to determine cure response in "optimized ovens ". Ovens were optimized in two different ways. In the first the bake time was fixed and oven air temperatures were adjusted so that the crosslink densities were as close as possible to the optimum value. In the second, oven air temperatures were varied to minimize the bake time subject to the constraint that all parts of the car be acceptably cured. Air temperatures were optimized for each of the different paints as a function of different sets of minimum and maximum heating rate constants. [Pg.268]

C. Methyl 3,3-dimethyl-4-oxobutanoate (3). A 50-mL flask, connected to a gas bubbler and equipped with a magnetic stirring bar, is charged with 20 mL of dichloromethane (or tetrahydrofuran), 2.16 g (10.0 mmol) of siloxycyclopropane 2 and 3.64 g (30.0 mmol) of triethylamine hydrofluoride (NEt3-HF) prepared in situ (Note 15). This mixture is stirred for 1 hr at room temperature (Note 16) and diluted with 20 mL of water. The aqueous phase is extracted with three 20-mL portions of dichloromethane. The combined organic phases are dried with magnesium sulfate, filtered, and concentrated on a rotary evaporator (bath temperature below 40°C). Crude product 3 is distilled with a Kugelrohr oven (oven temperature 105°C, 10 mm) to provide 1.26 g (87%) of pure 3 as a colorless liquid (Note 17). [Pg.232]

Drenching, spraying and dipping offer the advantages of varying contact times and concentrations to suit a specific product. These are more cost-effective methods because of the opportunity to recycle and reuse the smoke flavouring. Also, since smoke is applied to the product before it goes into the oven, oven cleanup costs are minimised. [Pg.304]

Tubular Ovens - Ovens that have cylindrical shapes. [Pg.546]

If splitting is desirable the films are often slit into a number of tapes before stretching in ordef to minimise transverse orientation during stretching. The distance between the feeding and traction rolls is increased to a few metres and the film is heated in infra-red ovens or, more often, in hot air circulating ovens. Ovens with a symmetrical air circulation have a certain advantage over ovens with an asymmetrical circulation. ... [Pg.439]

Oven drying (hydration stoppage) Removal of water from hydrated samples by circulating a warm, dry air flow through the oven. Oven temperatures are between 60 and 105°C. Drying is considered complete when the sample reaches constant mass. [Pg.506]

At low pressures, it is often permissible to neglect nonidealities of the vapor phase. If these nonidealities are not negligible, they can have the effect of introducing a nonrandom trend into the plotted residuals similar to that introduced by systematic error. Experience here has shown that application of vapor-phase corrections for nonidealities gives a better representation of the data by the model, oven when these corrections... [Pg.106]

The composition of coal tar varies with the carbonization method but consists, largely, of mononuclear and polynuclear aromatic compounds and their derivatives. Coke oven tars are relatively low in aliphatic and phenolic content while low-temperature tars have much higher contents of both. [Pg.103]

A bitumen sample is oxidized at high temperature under well defined conditions and its physical characteristics are measured before and after this artificiai ageing process. The method is defined in France as AFNOR T 66-032 and in the USA by ASTM D 2872 (Rolling Thin-Film Oven Test). [Pg.290]

RTFOT rolling thin film oven test... [Pg.503]

Figure B2.5.12 shows the energy-level scheme of the fine structure and hyperfme structure levels of iodine. The corresponding absorption spectrum shows six sharp hyperfme structure transitions. The experimental resolution is sufficient to detennine the Doppler line shape associated with the velocity distribution of the I atoms produced in the reaction. In this way, one can detennine either the temperature in an oven—as shown in Figure B2.5.12 —or the primary translational energy distribution of I atoms produced in photolysis, equation B2.5.35.

In most laboratories, drying ovens maintained at about 50° are available for the final drying of glass apparatus of all kinds. [Pg.40]

Dissolve 8 8 g. (9 0 ml.) of cyclohexanone in 50 ml. of glacial acetic acid, add 8 ml. of phenylhydrazine, and boil the solution under reflux for 5 minutes. Cool the solution, when the tetrahydrocarbazole will crystallise out. Filter at the pump, drain well, and recrystallise either from aqueous ethanol or (better) from aqueous acetic acid. The recrystallisation should be performed rapidly, for the tetrahydrocarbazole undergoes atmO" spheric oxidation in hot solutions after recrystallisation, the compound should be dried in a vacuum desiccator and not in an oven. Repeated recrystallisation should be avoided. The tetrahydrocarbazole, after thorough drying, is obtained as colourless crystals, m.p. 118° yield of recrystallised material, 11 g. [Pg.295]

Many chloroplatinates separate from aqueous solution with water of crystallisation. If this is suspected, the chloroplatinate should be dried to constant weight in the oven before analysis, to ensure elimination of water of crystallisation. Aniline, p-toluidine and pyridine all give anhydrous chloroplatinates, and can be conveniently used in the above determination no attempt should be made to recryrtallise their chloroplatinates. [Pg.450]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...