Substrates, solid

Films spread at liquid-liquid interfaces or on liquids other than water are discussed followed by the important effects of charged monolayers on water. Finally, the most technologically important application of Langmuir films, the Langmuir-Blodgett film deposited on a solid substrate, is reviewed. [Pg.537]

Other interesting Langmuir monolayer systems include spread thermotropic liquid crystals where a foam structure forms on expansion from a collapsed state [23]. Spread monolayers of clay dispersions form a layer of overlapping clay platelets that can be subsequently deposited onto solid substrates [24]. [Pg.542]

The interest in vesicles as models for cell biomembranes has led to much work on the interactions within and between lipid layers. The primary contributions to vesicle stability and curvature include those familiar to us already, the electrostatic interactions between charged head groups (Chapter V) and the van der Waals interaction between layers (Chapter VI). An additional force due to thermal fluctuations in membranes produces a steric repulsion between membranes known as the Helfrich or undulation interaction. This force has been quantified by Sackmann and co-workers using reflection interference contrast microscopy to monitor vesicles weakly adhering to a solid substrate [78]. Membrane fluctuation forces may influence the interactions between proteins embedded in them [79]. Finally, in balance with these forces, bending elasticity helps determine shape transitions [80], interactions between inclusions [81], aggregation of membrane junctions [82], and unbinding of pinched membranes [83]. Specific interactions between membrane embedded receptors add an additional complication to biomembrane behavior. These have been stud-... [Pg.549]

The transfer of Langmuir films from the air-liquid surface to a solid substrate has come to be known as Langmuir-Blodgett deposition, after its developers [130, 131]. The solid substrates are usually hydrophilic surfaces such as... [Pg.557]

The growth of solid films onto solid substrates allows for the production of artificial stmctures that can be used for many purposes. For example, film growth is used to create pn junctions and metal-semiconductor contacts during semiconductor manufacture, and to produce catalytic surfaces with properties that are not found in any single material. Lubrication can be applied to solid surfaces by the appropriate growth of a solid lubricating film. Film growth is also... [Pg.301]

Figure C2.4.2. Schematic sideview of tlie trough. The movable barrier is used to push tire molecules on tire subphase togetlier in tire Langmuir film which is subsequently transferred to a solid substrate.

Finally, rigid-rod polymers can be deposited on a solid substrate by the LB teclmique. These materials have both... [Pg.2619]

Cohen S R, Naaman R and Sagiv J 1986 Thermally induced disorder in organized organic monolayers on solid substrates J. Phys. Chem. 90 3054-6... [Pg.2631]

Four possible mechanisms for solid-state extraction (a) adsorption onto a solid substrate (b) absorption into a thin polymer or chemical film coated on a solid substrate (c) metal-ligand complexation in which the ligand is covalently bound to the solid substrate and (d) antibody-antigen binding in which the receptor is covalently bound to the solid substrate. [Pg.263]

When the nucleus is formed on a solid substrate by heterogeneous nucleation the above equations must be modified because of the nucleus-substrate interactions. These are reflected in the balance of the interfacial energies between the substrate and the environment, usually a vacuum, and the nucleus-vacuum and the nucleus-substrate interface energies. The effect of these terms is usually to reduce the critical size of the nucleus, to an extent dependent on... [Pg.25]

The most common heterogeneous catalytic reaction is hydrogenation. Most laboratory hydrogenations are done on liquid or solid substrates and usually in solution with a slurried catalyst. Therefore the most common batch reactor is a stirred vessel, usually a stirred autoclave (see Figure 2.1.1 for a typical example). In this system a gaseous compound, like hydrogen, must react at elevated pressure to accelerate the process. [Pg.30]

C fi3 diamond films can be deposited on a wide range of substrates (metals, semi-conductors, insulators single crystals and polycrystalline solids, glassy and amorphous solids). Substrates can be abraded to facilitate nucleation of the diamond film. [Pg.16]

Eqs. 4 and 6 enable the extent of contact between a liquid adhesive and a solid substrate to be gauged. Some consequences are shown in Table 1 where the concept of the reduced spreading coefficient S/yw, employed by Padday [10], was used to clarify the situation. As is readily seen, if S is positive, the liquid at equilibrium will be spread completely over the solid, but if S/yi is less than —2, spontaneous dewetting will occur. [Pg.321]

The adhesion promotion of an organic matrix to an inorganic substrate using a silane has been studied to model the structure of the created interphase [64-66]. The polymer/silane interphase is influenced by the solubility parameter of both the silane coupling agent and the polymer. More interdiffusion occurs when the solubility parameters of the polymer and the silane closely match together. It is believed that this model can be applied to silicone adhesive/solid substrate system. [Pg.696]

The force exerted by a thin fluid film on a solid substrate can be measured with nearly molecular precision in the SFA [27]. In the SFA a thin film is... [Pg.3]

A. Milchev, K. Binder. Dewetting of thin polymer films adsorbed on solid substrates A Monte Carlo simulation of the early stages. J Chem Phys 705 1978-1989, 1997. [Pg.625]

Solvents are often used in catalytic hydrogenation (< 7). Solvents may be one of the best means available for markedly altering the selectivity, a fact not sufficiently appreciated. Solvents also help to moderate the heat of hydroge nation, to aid in catalyst handling and recovery, and to permit the use of solid substrates. A convenient solvent may be the product itself or the solvent used in a prior or subsequent step. [Pg.8]

Although this technique has not been used extensively, it does allow structures of adsorbed layers on solid substrates to be studied. Liquid reflectivity may also be performed with a similar set-up, which relies on a liquid-liquid interface acting as the reflective surface and measures the reflectivity of a thin supported liquid film. This technique has recently been used to investigate water-alkane interfaces [55] and is potentially useful in understanding the interaction of ionic liquids with molecular solvents in which they are immiscible. [Pg.147]

Processes have been developed in North America to pilot scale growing the bacterium Cellulomonas or the fungus Trichoderma on pre-treated milled cellulosic material in conventional fermentors, ie in a liquid medium. However, preparation costs are considerably higher than with solid-substrate fermentations. [Pg.84]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...