Specific electron loss

Specific Electron Loss. Certain solvents, such as CC14, CFC13 or SF6 trap ejected electrons with high efficiency, and irreversibly, but the electron-loss centres are mobile via electron transfer, and hence can readily reach solute molecules (S) even in very low concentration. The sequence of reactions is summarised in reactions [11]-[14] for the most commonly used matrix, CFC13. [Pg.176]

We conclude that for organometallic derivatives, radiolysis can be used as an excellent method for inducing specific electron-loss or electron-addition. Furthermore, this can be done at very low temperatures such that, often, the primary gain and loss species are formed and can be characterised by e.s.r. spectroscopy. Thus this technique is a useful complement to more conventional studies of redox reactions. [Pg.191]

It is noteworthy that except for the Rieske center in Complex III, Complexes I and 11 are home to all the iron-sulfur clusters in the mitochondrial electron transfer chain and consequently most of the iron-containing carriers in the entire sequence. Hibbs subsequently showed that CAM-injured cells lose a substantial portion of their total intracellular iron (Hibbs et al., 1984) [later studies specifically identified loss of mitochondrial iron (Wharton et al., 1988)] and Drapier and Hibbs (1986) showed that the activity of another iron-sulfur-containing enzyme, aconitase, is also lost. In early 1987 Hibbs reported that the cytostatic actions of CAMs requires the presence of only one component in culture medium, L-arginine (Hibbs et al., 1987b). Thus, the stage was set for the discovery of a unique reactive species that targets intracellular iron, produced by CAMs. [Pg.142]

The distribution of product states of charge exchange of ions with incident energy W0 is described by dcrL(VT0)/dVT, where W is the energy of the Rydberg electron in the neutral product atom and Ol(Wo) is the total electron loss cross section. As in Eq. (3.3), we can write the charge exchange cross section for the population of a specific n state as... [Pg.31]

The debate over the site of electron loss in DNA is much less pronounced since it has been estimated that over 90% of the cations generated in DNA are centered on guanine [67] and guanine end products account for 90% of the electron loss products in DNA [70]. However, the spectra of G recorded in solid-state studies of nucleotides and nucleosides do not correspond to the spectrum recorded in fiiU DNA [71] and investigations of the strand-break specificity determined that some adenine cations could be generated [64]. Thus, it is also possible that other cations are formed, primarily A. ... [Pg.440]

Figure 1 shows the nuclear and electronic specific energy loss. [Pg.9]

Fig. 1. Nuclear and electronic specific energy loss S as a function of energy in dimensionless units...

Before the critical moment of a-y transition, when particles are relatively small and electron attachment is not effective, the electron balance is determined by ionization and electron losses to the walls. The a-y transition is the moment when the electron attachment to the particles exceeds the electron losses to the walls. The electron temperature increases to support the plasma balance (Belenguer et al., 1992). The total mass and volume of the particles remain almost constant during coagulation therefore, the specific surface of the particles decreases with the growth of mean particle radius. Hence, the influence of the particle surface becomes more significant, when the specific surface area decreases. Relation (8-154) explains the phenomenon the exponential part of the electron attachment dependence on particle radius is much more important than the pre-exponential factor. Comparison of the first and second terms on the right-hand side of (8-154) gives a critical particle size required for the a-y transition ... [Pg.577]

So why do the elements in the same family have similar properties And why do some families have the particular properties of electron loss or gain To find out, you can examine four specific families on the periodic table and look at the electron configurations for a few elements in each family. [Pg.60]

Any technique for gas analysis can be applied to EGA. The most frequently used methods are mass spectroscopy (MS) and Fourier transform infrared spectroscopy (FTIR). Many instrument manufacturers provide the ability to interface their TGAs with MS or FTIR (see Section 3.7, on instrumentation). Temporal resolution between the TGA and the MS or FTIR detector is an important feature, for example, in distinguishing absorbed water from water as a reaction product and in assigning a decomposition product to a specific mass loss. Each method has its experimental requirements, limitations, and advantages. Mass spectroscopy is a very sensitive technique that identifies volatile species by their mass-to-charge ratio, referred to as m/z. The evolution of the sum of all mJz species can be plotted and compared with the derivative TGA plot to ensure temporal resolution between the TGA and the mass spectrometer. The evolution of a specific mJz, associated with species such as water or formaldehyde, can show the distinct evolution of these compounds. The most common ionization is by 70eV electron impact (El), which operates... [Pg.249]

The main structural components in modem PEFCs are the porous composite electrodes. The primary purpose of utilizing porous electrodes is to enhance the active surface area of the catalyst by several orders of magnitude in comparison to planar electrodes with the same in-plane geometrical area. In the CLs, the fluxes of reactant gases, protons, and electrons meet at the catalyst particle surface. Active catalyst nanoparticles are located at spots that are connected simultaneously to the percolating phases of proton, electron, and gas transport media. An important implication of the electrode s finite thickness is the necessity to provide transport of neutral molecules and protons through the depth of the porous electrode. Additional overhead is caused by the transport of neutral reactants through FF, GDL, and MPL. This leads to specific potential losses in the electrodes, which will be considered in detail in Chapter 4. ... [Pg.7]

The investigation of aqueous electrolyte-air interface encounters a couple of intrinsic challenges. Firstly, the majority of material is dissolved in the bulk and the interfacial region comprises only a tiny fraction of the total material of the system. Consequently, spectroscopic investigations with classical techniques such as Infrared, Raman or UV-spectroscopy are often hampered by the lack of surface specificity and the signals are dominated by bulk contributions. Secondly, the processes at the air-water interface are highly dynamic. On a molecular scale there is a tremendous traffic towards both adjacent bulk phases. Molecules evaporate and condense at the interface and diffuse towards the bulk phase. There is no defined static molecular arrangement and as a consequence, fairly broad spectral features are expected. Moreover, many powerful surface specific techniques such as electron loss spectroscopy have special requirements to the sample and the environment (e.g. UHV-conditions) and cannot be applied to the liquid-air interface. [Pg.123]

Figure Bl.25.6. Energy spectrum of electrons coming off a surface irradiated with a primary electron beam. Electrons have lost energy to vibrations and electronic transitions (loss electrons), to collective excitations of the electron sea (plasmons) and to all kinds of inelastic process (secondary electrons). The element-specific Auger electrons appear as small peaks on an intense background and are more visible in a derivative spectrum.

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...