Systems dependence

A knock out vessel may on the other hand be followed by a variety of dehydrating systems depending upon the space available and the characteristics of the mixture. On land a continuous dehydration tank such as a wash tank may be employed. In this type of vessel crude oil enters the tank via an inlet spreader and water droplets fall out of the oil as it rises to the top of the tank. Such devices can reduce the water content to less than 2%. [Pg.247]

Hybrid systems. Depending on the problem to be solved, use can also be made of a combination of techniques leading to a hybrid system. For example, a rule-based system may use neural networks for solving classification subproblems (as is described in [Hopgood, 1993]), or a combination of a rule-based and a CBR system can be used as in the system for URS data interpretation described later in this paper. [Pg.99]

The resolution of images of the Real Time X-Ray system depend on the material thickness and on the settings of the system. While setting up the Real Time X-Ray inspection of parts the resolution is compared with the resolution aehieved in film bases X-Ray as used over the last years. It is demonstrated that the sensitivity of Real Time X-Ray meets the specification of DIN 54109 Bildgtitteklasse II. [Pg.457]

OPEN CLOSE STATEMENTS ARE USUALLY SYSTEM DEPENDENT... [Pg.221]

The choice of separation method to be appHed to a particular system depends largely on the phase relations that can be developed by using various separative agents. Adsorption is usually considered to be a more complex operation than is the use of selective solvents in Hquid—Hquid extraction (see Extraction, liquid-liquid), extractive distillation, or azeotropic distillation (see Distillation, azeotropic and extractive). Consequentiy, adsorption is employed when it achieves higher selectivities than those obtained with solvents. [Pg.291]

The space immediately above the resin bed may or may not be filled with Hquid in downward flow systems, depending on the design. If not filled, water entering the column from the top and impinging on the upper surface of the resin bed forms hills and valleys unless the flow is dispersed over the cross-sectional area. A distributor similar to the one used to collect resin below the bed, or splash plate, is placed a short distance above the resin bed to improve the distribution of the process stream flow. [Pg.381]

Dispersibility. The dispersibiHty of a pigment is measured by the effort required to develop the fuU tinctorial potential of a pigment in a vehicle system. DispersibiHty differs from system to system depending on pigment—medium interaction and compatibiHty. [Pg.23]

The choice of a specific CO2 removal system depends on the overall ammonia plant design and process integration. Important considerations include CO2 sHp required, CO2 partial pressure in the synthesis gas, presence or lack of sulfur, process energy demands, investment cost, availabiUty of solvent, and CO2 recovery requirements. Carbon dioxide is normally recovered for use in the manufacture of urea, in the carbonated beverage industry, or for enhanced oil recovery by miscible flooding. [Pg.349]

The results of the theory of quantum mechanics require that nuclear states have discrete energies. This is in contrast to classical mechanical systems, which can have any of a continuous range of energies. This difference is a critical fact in the appHcations of radioactivity measurements, where the specific energies of radiations are generally used to identify the origin of the radiation. Quantum mechanics also shows that other quantities have only specific discrete values, and the whole understanding of atomic and nuclear systems depends on these discrete quantities. [Pg.445]

Dispersion of a soHd or Hquid in a Hquid affects the viscosity. In many cases Newtonian flow behavior is transformed into non-Newtonian flow behavior. Shear thinning results from the abiHty of the soHd particles or Hquid droplets to come together to form network stmctures when at rest or under low shear. With increasing shear the interlinked stmcture gradually breaks down, and the resistance to flow decreases. The viscosity of a dispersed system depends on hydrodynamic interactions between particles or droplets and the Hquid, particle—particle interactions (bumping), and interparticle attractions that promote the formation of aggregates, floes, and networks. [Pg.173]

Fermentation. The term fermentation arose from the misconception that black tea production is a microbial process (73). The conversion of green leaf to black tea was recognized as an oxidative process initiated by tea—enzyme catalysis circa 1901 (74). The process, which starts at the onset of maceration, is allowed to continue under ambient conditions. Leaf temperature is maintained at less than 25—30°C as lower (15—25°C) temperatures improve flavor (75). Temperature control and air diffusion are faciUtated by distributing macerated leaf in layers 5—8 cm deep on the factory floor, but more often on racked trays in a fermentation room maintained at a high rh and at the lowest feasible temperature. Depending on the nature of the leaf, the maceration techniques, the ambient temperature, and the style of tea desired, the fermentation time can vary from 45 min to 3 h. More highly controlled systems depend on the timed conveyance of macerated leaf on mesh belts for forced-air circulation. If the system is enclosed, humidity and temperature control are improved (76). [Pg.372]

The energy density of the system depends on the type of cell as well as the current drain. Table 3 gives the specification for the various hthium systems. These coia cells have already been widely used ia electronic devices such as calculators and watches, whereas the cylindrical cells have found apphcations ia cameras. [Pg.534]

Coating solutions often exhibit a mixture of viscous and elastic behavior, with the response of a particular system depending on the stmcture of the material and the extent of deformation. Eor example, polymer melts can be highly elastic if a polymer chain can stretch when subjected to deformation. [Pg.304]

The dominant crystal size, is most often used as a representation of the product size, because it represents the size about which most of the mass in the distribution is clustered. If the mass density function defined in equation 33 is plotted for a set of hypothetical data as shown in Figure 10, it would typically be observed to have a maximum at the dominant crystal size. In other words, the dominant crystal size is that characteristic crystal dimension at which drajdL = 0. Also shown in Figure 10 is the theoretical result obtained when the mass density is determined for a perfectiy mixed, continuous crystallizer within which invariant crystal growth occurs. That is, mass density is found for such systems to foUow a relationship of the form m = aL exp —bL where a and b are system-dependent parameters. [Pg.348]

The mechanisms that control dmg deUvery from pumps may be classified as vapor-pressure, electromechanical, or elastomeric. The vapor-pressure controlled implantable system depends on the principle that at a given temperature, a Hquid ia equiUbrium with its vapor phase produces a constant pressure that is iadependent of the enclosing volume. The two-chamber system contains iafusate ia a flexible beUows-type reservoir and the Hquid power source ia a separate chamber (142). The vapor pressure compresses the dmg reservoir causiag dmg release at a constant rate. Dmg maybe added to the reservoir percutaneously via a septum, compressing the fluid vapor iato the Hquid state. [Pg.233]

The choice of initiator system depends on the polymerization temperature, which is an important factor in determining final product properties. Cold polymers are generally easier to process than hot polymers and in conventional cured mbber parts have superior properties. The hot polymers are more highly branched and have some advantages in solution appHcations such as adhesives, where the branching results in lower solution viscosity and better cohesion in the final adhesive bond. [Pg.520]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...