Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Tensile yield

Tensile yield strength, 103 lb in-2 Thermal Burning rate, mm min Coefficient of linear thermal expansion, 10 °C 50-90 0.5-2.2 50-90 50-80 50-60 10-13 Self- extinguishing 40-55 46... [Pg.1029]

Tensile yield strength, 1Q3 lb in-3 Thermal Burning rate, mm min Not Not Not Not Not Self- Self-... [Pg.1037]

Yield pressurep of the asperities is about three times the tensile yield strength for many materials. The real area of contact is frequently a minute fraction of the total area. With a typical bearing contact stress of 3 MPa and a bron2e bearing asperity yield pressure of 500 MPa, for instance, less than 1.0% of the nominal area would involve asperity contact. [Pg.233]

ASTM UNS Temper Least dimension, mm Area, cm Tensde Tensile yield... [Pg.326]

AHoy and temper Tensile Yield strength. Elongation, % BrineU... [Pg.120]

But we want the tensile yield strength, A tensile stress a creates a shear stress in the material that has a maximum value of t = a/2. (We show this in Chapter 11 where we resolve the tensile stress onto planes within the material.) To calculate cr from t,, we combine the Taylor factor with the resolution factor to give... [Pg.109]

The joint is designed so that the solder layer will yield in shear at the same axial load f that causes the main tube to fail by tensile yield. Estimate the required value of W, given the following data f = 1 mm dy (copper) = 120 MPa dy (solder) = 10 MPa. [Pg.157]

Material Condition Ultimate tensile Yield strength ... [Pg.157]

Many meehanieal eomponents also operate at temperatures far lower than room temperature. As the temperature is redueed, both the ultimate tensile strength, Su, and tensile yield strength, Sy, generally inerease for most materials. Flowever, temperatures below freezing have the effeet of altering the strueture of some duetile... [Pg.159]

Therefore, the Normal distribution parameters for the material s tensile yield strength are 1 /0.577 times greater, giving ... [Pg.234]

Figure 11-7. Turbine Wheel Alloys tensile yield strength comparison. Figure 11-7. Turbine Wheel Alloys tensile yield strength comparison.
Figure 11.3. Variation of tensile yield stress with melt flow index (10 kg load at 190 C) and isotactic index. (After Crespi and Ranalli )... Figure 11.3. Variation of tensile yield stress with melt flow index (10 kg load at 190 C) and isotactic index. (After Crespi and Ranalli )...
Melt Flow Ratio 230°C/2.16kg Tensile Yield g/lOmin ISOI133 30 48 48... [Pg.256]

See other pages where Tensile yield is mentioned: [Pg.1027]    [Pg.1031]    [Pg.1033]    [Pg.1035]    [Pg.1041]    [Pg.1043]    [Pg.1047]    [Pg.1049]    [Pg.1051]    [Pg.1053]    [Pg.1055]    [Pg.1057]    [Pg.1059]    [Pg.1061]    [Pg.360]    [Pg.374]    [Pg.96]    [Pg.96]    [Pg.328]    [Pg.328]    [Pg.371]    [Pg.429]    [Pg.266]    [Pg.333]    [Pg.334]    [Pg.450]    [Pg.503]    [Pg.370]    [Pg.990]    [Pg.111]    [Pg.279]    [Pg.240]    [Pg.425]    [Pg.496]    [Pg.510]   
See also in sourсe #XX -- [ Pg.370 ]



SEARCH



Clay tensile yield stress

Cooling tensile yield stress

Irradiation tensile yield

Material properties tensile yield stress

Stress variation, tensile yield

Tensile elongation at yield

Tensile loading, yield stresses

Tensile strength at yield

Tensile stress-yield strength ratio

Tensile yield strength

Tensile yield stress

Uniaxial tensile loading, yield stresses

Yield criteria tensile

© 2024 chempedia.info