Weak points

A new countercurrent continuous centrifugal extractor developed in the former USSR (214) has the feature that mechanical seals are replaced by Hquid seals with the result that operation and maintenance are simplified the mechanical seals are an operating weak point in most centrifugal extractors. The operating units range between 400 and 1200 mm in diameter, and a capacity of 70 m /h has been reported in service. The extractors have been appHed in coke-oven refining (see Coal conversion processes), erythromycin production, lube oil refining, etc. [Pg.77]

This combination of monomers is unique in that the two are very different chemically, and in thek character in a polymer. Polybutadiene homopolymer has a low glass-transition temperature, remaining mbbery as low as —85° C, and is a very nonpolar substance with Htde resistance to hydrocarbon fluids such as oil or gasoline. Polyacrylonitrile, on the other hand, has a glass temperature of about 110°C, and is very polar and resistant to hydrocarbon fluids (see Acrylonitrile polymers). As a result, copolymerization of the two monomers at different ratios provides a wide choice of combinations of properties. In addition to providing the mbbery nature to the copolymer, butadiene also provides residual unsaturation, both in the main chain in the case of 1,4, or in a side chain in the case of 1,2 polymerization. This residual unsaturation is useful as a cure site for vulcanization by sulfur or by peroxides, but is also a weak point for chemical attack, such as oxidation, especially at elevated temperatures. As a result, all commercial NBR products contain small amounts ( 0.5-2.5%) of antioxidant to protect the polymer during its manufacture, storage, and use. [Pg.516]

Welds represent particularly weak points. The sheet itself is mechanically shot blasted in the factory or in the shipyard and given a shop primer. The installation... [Pg.396]

There is much evidence that weak links are present in the chains of most polymer species. These weak points may be at a terminal position and arise from the specific mechanism of chain termination or may be non-terminal and arise from a momentary aberration in the modus operandi of the polymerisation reaction. Because of these weak points it is found that polyethylene, polytetrafluoroethylene and poly(vinyl chloride), to take just three well-known examples, have a much lower resistance to thermal degradation than low molecular weight analogues. For similar reasons polyacrylonitrile and natural rubber may degrade whilst being dissolved in suitable solvents. [Pg.96]

PVC has a rather limited thermal stability. This is rather surprising since it is known that low molecular weight materials containing similar structures cire far more stable. It would thus appear that this instability is due to imperfections or weak points in the structure at which degradation can commence. The... [Pg.319]

In view of its position in the e.m.f. series ( °aj3+/ai = 166V (SHE)), aluminium would be expected to be rapidly attacked even by dilute solutions of relatively weak acids. In fact, the rate of chemical attack is slow, owing to the presence on the aluminium of a thin compact film of air-formed oxide. When a voltage is applied to an aluminium anode there is a sudden initial surge of current, as this film is ruptured, followed by a rapid fall to a lower, fairly steady value. It appears that this is due to the formation of a barrier-layer. Before the limiting thickness is reached, however, the solvent action of the electrolyte initiates a system of pores at weak points or discontinuities in the oxide barrier-layer. [Pg.691]

The relative importance of these functions also depends to a considerable extent on the solution conditions. Under favourable conditions of pH, oxidising power and aggressive anion concentration in the solution, Function 1 is probably effective in preventing film breakdown. Under unfavourable conditions for inhibition, localised breakdown will occur at weak points in the oxide film, and Functions 2 and 3 become important in repairing the oxide film. [Pg.824]

Jetting Jetting is a condition that results when the mold design has no immediate impediment to flow and the plastics is ejected into a relatively large open volume. This jetted material becomes a weak point on the product and a surface blemish that is difficult to conceal. [Pg.280]

Eaeh pieee of equipment used to manufaeture or pack pharmaceuticals has its own peculiar area where mierobial growth may be supported, and knowledge of its weak points may be built up by regular tests for eontamination. The type and extent of growth will depend on the souree of the eontamination, the nutrients available and the environmental conditions, in particular the temperature and pH. [Pg.350]

The theory of electrolytic dissociation was not immediately recognized universally, despite the fact that it could qualitatively and quantitatively explain certain fundamental properties of electrolyte solutions. For many scientists the reasons for spontaneous dissociation of stable compounds were obscure. Thus, an energy of about 770kJ/mol is required to break up the bonds in the lattice of NaCl, and about 430kJ/mol is required to split H l bonds during the formation of hydrochloric acid solution. Yet the energy of thermal motions in these compounds is not above lOkJ/mol. It was the weak point of Arrhenius s theory that this mismatch could not be explained. [Pg.105]

This area, is in fact, the weak point in most studies of risk chemistry, and also notably, in the regulatory safety data publications mentioned above. [Pg.19]

After the four ranks for levels of risk for fire, instability, toxicity and reactivity are established, other ranks will appear - dedicated to the operators involved (are they able to cope with potential dangers ), the peculiarities involved in setting up the apparatus (detecting weak points eg), effect of environmental conditions (lighting, supervision etc), and any rank likely to be involved in the globai security of the process. [Pg.33]

More efficient estimation methods exist than the simple method described here [17]. The generalized standard addition method (GSAM) shares the strong points (e.g correction for interferences) and weak points (e.g. error amplification because of the extrapolation involved) of the simple standard addition method [18]. [Pg.368]

FIGURE 2.1 A side view of the structure of the prototype G-protein-coupled, 7TM receptor rhodopsin. The x-ray structure of bovine rhodopsin is shown with horizontal gray lines, indicating the limits of the cellular lipid membrane. The retinal ligand is shown in a space-filling model as the cloud in the middle of the structure. The seven transmembrane (7TM) helices are shown in solid ribbon form. Note that TM-III is rather tilted (see TM-III at the extracellular and intracellular end of the helix) and that kinks are present in several of the other helices, such as TM-V (to the left), TM-VI (in front of the retinal), and TM-VII. In all of these cases, these kinks are due to the presence of a well-conserved proline residue, which creates a weak point in the helical structure. These kinks are believed to be of functional importance in the activation mechanism for 7TM receptors in general. Also note the amphipathic helix-VIII which is located parallel to the membrane at the membrane interface. [Pg.85]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...