M5Camera-F New
Description
M5Camera-F New is a fisheye wide-angle image recognition development board with a field of view of 150°. It integrates the ESP32 (4M Flash + 520K RAM + 4M PSRAM) chip and a 2-megapixel camera (OV2640). It supports WiFi image transmission and USB port debugging.
The hardware comes pre-installed with firmware, and it can be programmed and developed using ESP-IDF to run the WiFi-camera application. The default program outputs an image size of 600 x 800, but you can optimize the program to output larger sizes.
How to use this program?
- Turn on your phone's Wi-Fi, scan and connect to the AP hotspot with a name starting with "m5stack-".
- Open your phone's browser and visit 192.168.4.1 to access the monitoring page and get real-time video footage.
- The video frame rate is approximately 5-6 frames per second.
Since the module can generate a WIFI hotspot AP, you can use a phone, PC, or other devices to wirelessly obtain camera images via WIFI, or you can obtain camera images via the module's HY2.0-4P interface.
Features
- Based on ESP32 design
- WIFI image transmission
- CP2104 USB TTL
- Wide-angle lens 150°
- OV2640 visual sensor
Includes
- 1 x M5Camera-F New
- 1 x LEGO adapter clip
- 1 x Wall/1515
- 1 x USB Type-C cable (20cm)
Specifications
| Specification | Parameter |
|---|---|
| Flash | 4M |
| RAM | 4MB |
| Image Sensor | OV2640 |
| Maximum Resolution | 2 Megapixels |
| Output Format | YUV (422/420) /YCbCr422, 8-bit compressed data, RGB565/555, 8-/10-bit Raw RGB data |
| Field of View | 150° |
| CCD Size | 1/4 inch |
| Net Weight | 17g |
| Gross Weight | 41g |
| Product Dimensions | 24 x 48 x 19mm |
| Package Dimensions | 75 x 45 x 30mm |
Schematics
Power Circuit
Chip Peripheral Circuit
USB to Serial Circuit
PinMap
Camera
| Interface | Camera Pin | M5CameraF |
|---|---|---|
| SCCB Clock | SIOC | IO23 |
| SCCB Data | SIOD | IO22 |
| System Clock | XCLK | IO27 |
| Vertical Sync | VSYNC | IO25 |
| Horizontal Reference | HREF | IO26 |
| Pixel Clock | PCLK | IO21 |
| Pixel Data Bit 0 | D2 | IO32 |
| Pixel Data Bit 1 | D3 | IO35 |
| Pixel Data Bit 2 | D4 | IO34 |
| Pixel Data Bit 3 | D5 | IO5 |
| Pixel Data Bit 4 | D6 | IO39 |
| Pixel Data Bit 5 | D7 | IO18 |
| Pixel Data Bit 6 | D8 | IO36 |
| Pixel Data Bit 7 | D9 | IO19 |
| Camera Reset | RESET | IO15 |
| Camera Power Down | PWDN | see Note 1 |
| Power Supply 3.3V | 3V3 | 3V3 |
| Ground | GND | GND |
HY2.0-4P Interface
| HY2.0-4P | M5CameraF |
|---|---|
| SCL | G4 |
| SDA | G13 |
| 5V | 5V |
| GND | GND |
LED
| LED | M5Camera |
|---|---|
| LED_Pin | IO14 |
The PIN8 (PDWN) of the OV2640 chip is the enable pin. In this motherboard, it is enabled by a 12KΩ pull-down resistor to ground, entering the working mode. When PIN8 (PDWN) is pulled high, it will enter Camera Power Down mode.
Datasheets
Softwares
Arduino
ESP-IDF
- M5Stack-Camera
- M5CameraF Firmware
- UART Communication-M5CameraF **
- UART Communication-M5Core
- QR Code Recognition
- MPU6050
EasyLoader
| Easyloader | Download Link | Notes |
|---|---|---|
| M5Camera-F New AP Firmware Easyloader | download | / |