MPU6886.h

/*
 Note: The MPU6886 is an I2C sensor and uses the Arduino Wire library.
 Because the sensor is not 5V tolerant, we are using a 3.3 V 8 MHz Pro Mini or
 a 3.3 V Teensy 3.1. We have disabled the internal pull-ups used by the Wire
 library in the Wire.h/twi.c utility file. We are also using the 400 kHz fast
 I2C mode by setting the TWI_FREQ  to 400000L /twi.h utility file.
 */
#ifndef _MPU6886_H_
#define _MPU6886_H_

#include <Arduino.h>
#include <Wire.h>

#include "MahonyAHRS.h"

#define MPU6886_ADDRESS          0x68
#define MPU6886_WHOAMI           0x75
#define MPU6886_ACCEL_INTEL_CTRL 0x69
#define MPU6886_SMPLRT_DIV       0x19
#define MPU6886_INT_PIN_CFG      0x37
#define MPU6886_INT_ENABLE       0x38
#define MPU6886_ACCEL_XOUT_H     0x3B
#define MPU6886_ACCEL_XOUT_L     0x3C
#define MPU6886_ACCEL_YOUT_H     0x3D
#define MPU6886_ACCEL_YOUT_L     0x3E
#define MPU6886_ACCEL_ZOUT_H     0x3F
#define MPU6886_ACCEL_ZOUT_L     0x40

#define MPU6886_TEMP_OUT_H 0x41
#define MPU6886_TEMP_OUT_L 0x42

#define MPU6886_GYRO_XOUT_H 0x43
#define MPU6886_GYRO_XOUT_L 0x44
#define MPU6886_GYRO_YOUT_H 0x45
#define MPU6886_GYRO_YOUT_L 0x46
#define MPU6886_GYRO_ZOUT_H 0x47
#define MPU6886_GYRO_ZOUT_L 0x48

#define MPU6886_USER_CTRL     0x6A
#define MPU6886_PWR_MGMT_1    0x6B
#define MPU6886_PWR_MGMT_2    0x6C
#define MPU6886_CONFIG        0x1A
#define MPU6886_GYRO_CONFIG   0x1B
#define MPU6886_ACCEL_CONFIG  0x1C
#define MPU6886_ACCEL_CONFIG2 0x1D
#define MPU6886_FIFO_EN       0x23

#define MPU6886_FIFO_ENABLE 0x23
#define MPU6886_FIFO_COUNT  0x72
#define MPU6886_FIFO_R_W    0x74
#define MPU6886_GYRO_OFFSET 0x13
//#define G (9.8)
#define RtA     57.324841
#define AtR     0.0174533
#define Gyro_Gr 0.0010653

class MPU6886 {
   public:
    enum Ascale { AFS_2G = 0, AFS_4G, AFS_8G, AFS_16G };

    enum Gscale { GFS_250DPS = 0, GFS_500DPS, GFS_1000DPS, GFS_2000DPS };

   public:
    MPU6886();
    int Init(void);
    void getAccelAdc(int16_t* ax, int16_t* ay, int16_t* az);
    void getGyroAdc(int16_t* gx, int16_t* gy, int16_t* gz);
    void getTempAdc(int16_t* t);

    void getAccelData(float* ax, float* ay, float* az);
    void getGyroData(float* gx, float* gy, float* gz);
    void getTempData(float* t);

    void setGyroFsr(Gscale scale);
    void setAccelFsr(Ascale scale);

    void getAhrsData(float* pitch, float* roll, float* yaw);
    void setFIFOEnable(bool enableflag);
    uint8_t ReadFIFO();
    void ReadFIFOBuff(uint8_t* DataBuff, uint16_t Length);
    uint16_t ReadFIFOCount();
    void RestFIFO();
    void setGyroOffset(uint16_t x, uint16_t y, uint16_t z);

   public:
    float aRes, gRes, imuId;
    Gscale Gyscale;
    Ascale Acscale;

   private:
   private:
    void I2C_Read_NBytes(uint8_t driver_Addr, uint8_t start_Addr,
                         uint8_t number_Bytes, uint8_t* read_Buffer);
    void I2C_Write_NBytes(uint8_t driver_Addr, uint8_t start_Addr,
                          uint8_t number_Bytes, uint8_t* write_Buffer);
    void updateGres();
    void updateAres();
};
#endif