people_outline
Application example: Suppressing the coffee ring effect to fabricate asymmetric supraparticles
DataPhysics Instruments Logo

Suppressing the coffee ring effect to fabricate asymmetric supraparticles

Fuel Cells - Studying contact angles at high temperatures

Studying how droplets, that contain solid particles, evaporate from a solid surface reveals a perplexing procedure. The combination of mass and heat transfer lead to intriguing phenomena, such as the coffee-ring effect, which describes the evaporation of colloidal droplets on a solid surface, generating non-uniform ring-like depositions. The results of this process have an impact, in many research areas, where a uniform particle deposition is a crucial requirement, such as biosensors, inkjet-printing, photonics and others. Recently, Butt et al. reported that control and regulation of the evaporation of water droplets, on oil-coated surfaces, can suppress the coffee-ring effect and produce asymmetric supraparticles.

How can the coffee ring effect be avoided, and a uniform deposition guaranteed?

In order to understand the processes of droplet evaporation, Butt et al. studied the droplet evaporation on surfaces, with and without an oil film. The droplet evaporated more slowly on the oil-coated surface and formed a homogenous pattern. During the evaporation process on an oil coated substrate two contact lines (interfaces) are present on the droplet surface: a liquid−liquid−air contact line (LLA-CL) and a liquid−liquid−solid contact line (LLS-CL). In contrast, the droplet evaporation on the bare glass surface was significantly faster, with only a single contact line, a liquid-air-solid contact line (LAS-CL), and generated a typical coffee ring, due to the outward capillary flow inside the droplet.

Top: Evaporation process of a water-based suspension leading to the

Top: Evaporation process of a water-based suspension leading to the coffee ring. Bottom: Oil coated surface suppresses evaporation below the liquid-liquid-air contact line (LLA-CL) and leads to a uniform deposition of particles.

Moreover, the figure illustrates that there is a tendency for colloidal particles to be transported to the upper interface (LLA-CL) and accumulate there. This phenomenon is a result of hindered evaporation, both on the oil-coated water drop surface, and from the bottom edge LLS-CL. Only at the uncovered area of the droplet evaporation can occur freely. This localized evaporation results in an upward flow, of particulate matter inside the drop, which, in the first instance, concentrates the dispersion towards the upper surface of the drop, during the evaporation and facilitates a uniform deposition on the substrate. The oil viscosity, film thickness, droplet size, and concentration of the colloids were all found to influence the deposition pattern.

Fluorescent polystyrene particles were used as tracers and observed by confocal microscopy in order to get a deeper understanding of the particle flow during evaporation. The results show that the droplets deposition radius on the oil-coated surfaces decreases with time, while the contact angle at the droplet edge changes only slightly. This phenomenon indicates that the droplet edge is continuously receding and the pinning of particles, to the substrate surface, is not an immediate effect.

For comparison, on the non-oil-coated surface, the deposition radius did not change, while the contact angle is much smaller than on the oil-coated surfaces and decreases during the whole evaporation process. This is caused by the fact that for the non-oil coated surface the particles are already pinned to the surface at the beginning of the evaporation.

Visualization of the coffee ring effect

With the Surface Profile Analyzer SPA 25 the deposition of particles can be analyzed and visualized with exceptional resolution. Hence, for example the ring-like structures left behind by a particle-based silver ink could be analyzed. Smallest individual droplets of the silver ink were dosed onto a substrate using the picolitre dosing system PDDS. After the ink dried the coffee ring effect was observed and the sample analyzed with the SPA 25.

Ring-like deposition of a particle-based silver ink recorded by the Surface Profile Analyzer SPA25

Ring-like deposition of a particle-based silver ink recorded by the Surface Profile Analyzer SPA 25

This research demonstrates a novel method through which the coffee ring effect (nonuniform deposition) can be avoided. By regulating the evaporation of droplets on oil-coated surfaces a uniform deposition of suspended particles during drop evaporation is achieved.

An optical contact angle measuring and contour analysis system of the OCA series and a tensiometer of the DCAT series were used in this research. For more information, please refer to the original publication:

References