What should be done if engine mounts are broken or deteriorated on Dodge Grand Caravan?

Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or wear on driveline components. During the check, the engine must be raised slightly to remove the weight from the mounts. Raise the vehicle and support it securely on jackstands, then position a jack under the engine oil pan with a large block of wood between the jack head and the oil pan, carefully raising the engine just enough to relieve the weight on the mounts. Inspect the mount insulators for cracks, hardened rubber, or separation from the metal plates, noting that the rubber may split down the center. Check for relative movement between the mount plates and the engine or frame using a large screwdriver or prybar; if movement is noted, lower the engine and tighten the mount fasteners. Apply rubber preservative to the insulators to slow deterioration. To replace the mounts, disconnect the negative battery cable, raise the vehicle, and support it securely on jackstands if not already done. Remove the fasteners and detach the insulator from the frame bracket, then raise the engine slightly with a jack or hoist, remove the insulator-to-engine bolts, and detach the insulator. Installation follows the reverse order of removal, using thread locking compound on the mount bolts and ensuring they are tightened securely. The right and left engine mounts are adjustable to allow drivetrain movement in relation to driveaxle assembly length, and adjustments should be made when servicing the driveaxles, after front end structural damage, or when replacing a mount. Remove the load on the engine mounts by carefully supporting the engine and transaxle assembly with a floor jack, then loosen the right insulator vertical fasteners and the front engine mount bracket-to-front crossmember bolts and nuts. The left engine mount insulator is sleeved over the shaft and long support bolt to provide lateral movement adjustment. Pry the engine right or left as required to achieve the proper driveaxle length, then securely tighten the right engine mount insulator vertical bolts, the front engine mount bolts and nuts, and center the left engine mount insulator. Finally, recheck the driveaxle length.

Genuine Dodge Grand Caravan Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

87 Engine Mounts found

View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 5273893AF
$94.25 MSRP: $144.00
You Save: $49.75 (35%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount; Rear Mount, Rear Support
- Replaces: 5273893AE, 5273893AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2020 Dodge Grand Caravan | C/V, Crew, Express, GT, LUX, Mainstreet, R/T, SE, SXT | 6 Cyl 3.6L
View related parts
Dodge Grand Caravan Support
Part Number: 5273883AD
$226.87 MSRP: $341.00
You Save: $114.13 (34%)
ADD TO CART
Product Specifications
- Other Name: Engine Mount Front; Front Mount, Front Support
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2020 Dodge Grand Caravan | Crew, GT, R/T, SE, SXT | 6 Cyl 3.6L
View related parts
Dodge Grand Caravan ISOLATOR-Engine Mount
Part Number: 4721746AB
$58.46 MSRP: $86.20
You Save: $27.74 (33%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2020 Dodge Grand Caravan | C/V, Crew, Express, GT, Hero, LUX, Mainstreet, R/T, SE, SXT | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Dodge Grand Caravan Support-Engine
Part Number: 4721871AE
$79.72 MSRP: $122.00
You Save: $42.28 (35%)
ADD TO CART
Product Specifications
- Other Name: Support Engine; Lower Support
- Replaces: 4721871AD, 4809828AG, 4809828AF, 4721871AC, 4809828AE, 4721871AA, 4721871AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2020 Dodge Grand Caravan | C/V, Crew, Express, GT, Hero, LUX, Mainstreet, R/T, SE, SXT | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Dodge Grand Caravan Support-Rt
Part Number: 4612367
$33.26 MSRP: $67.75
You Save: $34.49 (51%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount; Mount, Side Support, Support
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Dodge Grand Caravan | Base, ES FWD, LE AWD, LE FWD, SE AWD, SE FWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 5110502AC
$193.04 MSRP: $257.00
You Save: $63.96 (25%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount
- Replaced by: 5110502AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Grand Caravan | C/V, Crew, Hero, SE, SXT | 6 Cyl 3.3L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 4861271AD
$112.88 MSRP: $170.00
You Save: $57.12 (34%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount; Mount, Side Support
- Position: Passenger Side
- Replaces: 4861271AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2007 Dodge Grand Caravan | C/V, EL, ES FWD, EX, SE, Sport FWD, SXT FWD | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 4861295AB
$83.05 MSRP: $127.00
You Save: $43.95 (35%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount; Front Support, Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Dodge Grand Caravan | C/V, EL, ES AWD, ES FWD, EX, SE, Sport AWD, Sport FWD, SXT AWD, SXT FWD | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 4880492AA
$107.68 MSRP: $224.00
You Save: $116.32 (52%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount
- Replaced by: 4880492AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Grand Caravan | C/V, Crew, Hero, SE, SXT | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Dodge Grand Caravan Support-Transmission Mount
Part Number: 5273996AE
$95.03 MSRP: $144.00
You Save: $48.97 (35%)
ADD TO CART
Product Specifications
- Other Name: Support Transmission Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2020 Dodge Grand Caravan | C/V, Crew, Express, GT, LUX, Mainstreet, R/T, SE, SXT | 6 Cyl 3.6L
View related parts
Dodge Grand Caravan Insulator
Part Number: 5273994AB
$130.81 MSRP: $197.00
You Save: $66.19 (34%)
ADD TO CART
Product Specifications
- Other Name: Engine Mount Right; Side Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2020 Dodge Grand Caravan | C/V, Crew, Express, GT, LUX, Mainstreet, R/T, SE, SXT | 6 Cyl 3.6L
View related parts
Dodge Grand Caravan Support-Engine
Part Number: 4809828AE
$79.81 MSRP: $122.00
You Save: $42.19 (35%)
ADD TO CART
Product Specifications
- Other Name: Support Engine
- Replaced by: 4721871AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Grand Caravan | C/V, Crew, Hero, SE, SXT | 6 Cyl 3.3L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 5273893AE
$95.03 MSRP: $144.00
You Save: $48.97 (35%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount
- Replaced by: 5273893AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2013 Dodge Grand Caravan | Crew, R/T, SE, SXT | 6 Cyl 3.6L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 5273893AD
$95.03 MSRP: $144.00
You Save: $48.97 (35%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount
- Replaced by: 5273893AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Dodge Grand Caravan | C/V, Crew, Express, LUX, Mainstreet, R/T | 6 Cyl 3.6L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 4880494AA
$122.98 MSRP: $185.00
You Save: $62.02 (34%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount
- Replaced by: 4880494AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Grand Caravan | Crew, SXT | 6 Cyl 4.0L
View related parts
Dodge Grand Caravan Bracket-Engine Mount
Part Number: 4861298AE
$96.20 MSRP: $169.00
You Save: $72.80 (44%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount
- Replaced by: 4861298AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Dodge Grand Caravan | C/V, EL, ES AWD, ES FWD, EX, SE, Sport AWD, Sport FWD, SXT AWD, SXT FWD | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Dodge Grand Caravan DAMPER-Engine Mount
Part Number: 4721672AC
$71.90 MSRP: $151.00
You Save: $79.10 (53%)
ADD TO CART
Product Specifications
- Other Name: DAMPER Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2011 Dodge Grand Caravan | C/V, Crew, Express, LUX, Mainstreet, R/T, SXT | 6 Cyl 3.6L, 6 Cyl 4.0L
View related parts
Dodge Grand Caravan Bracket-Engine Mount
Part Number: 4721570AB
$105.78 MSRP: $160.00
You Save: $54.22 (34%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Engine Bracket
- Replaces: 4721570AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2020 Dodge Grand Caravan | C/V, Crew, Express, GT, LUX, Mainstreet, R/T, SE, SXT | 6 Cyl 3.6L
View related parts
Dodge Grand Caravan Support-Engine Mount
Part Number: 5110501AC
$169.94 MSRP: $257.00
You Save: $87.06 (34%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount
- Replaced by: 5110502AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Grand Caravan | SXT | 6 Cyl 3.8L
View related parts
Dodge Grand Caravan Bracket-Engine Mount
Part Number: 4809939AF
$136.40 MSRP: $205.00
You Save: $68.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Front Mount Bracket
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2020 Dodge Grand Caravan | C/V, Crew, Express, GT, LUX, Mainstreet, R/T, SE, SXT | 6 Cyl 3.6L

| Page 1 of 5 |Next >

1-20 of 87 Results

Dodge Grand Caravan Engine Mount

The Engine Mount in Dodge Grand Caravan vehicles serves two primary functions: it reduces noise and vibration from running the engine and also provides Firm anchorage for the Engine and transaxle assembly within the chassis. To achieve comfort of the occupant, isolation is important while to achieve safe driving of the vehicle and prevent wear and tear of components, maintaining the position of the engine is important. Dodge Grand Caravan models have incorporated sundry types of Engine Mounts apart from the existing rubber Engine Mounts, fluid-filled hydraulic Engine Mounts, and intelligent active Engine Mounts. The old types of mounts are metallic where their supports include rubber washers while the new types of hydraulic mounts have more of the ability to counter vibration. The newest active mounts are self-sensing and change stiffness according to rpm of the engine, improving performance. Engine Mounts are known to fail over time depending on their age, heat or fluid damage and this can manifest in weird noises and shaking that will require inspection for change.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Grand Caravan Engine Mount at great affordable prices. Moreover, all genuine Dodge Grand Caravan Engine Mount come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Grand Caravan Engine Mount Parts Questions & Experts Answers

Support-Engine Mount
4861478AB
Q: What should be done if engine mounts are broken or deteriorated on Dodge Grand Caravan?
A: Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or wear on driveline components. During the check, the engine must be raised slightly to remove the weight from the mounts. Raise the vehicle and support it securely on jackstands, then position a jack under the engine Oil Pan with a large block of wood between the jack head and the oil pan, carefully raising the engine just enough to relieve the weight on the mounts. Inspect the mount insulators for cracks, hardened rubber, or separation from the metal plates, noting that the rubber may split down the center. Check for relative movement between the mount plates and the engine or frame using a large screwdriver or prybar; if movement is noted, lower the engine and tighten the mount fasteners. Apply rubber preservative to the insulators to slow deterioration. To replace the mounts, disconnect the negative battery cable, raise the vehicle, and support it securely on jackstands if not already done. Remove the fasteners and detach the insulator from the frame bracket, then raise the engine slightly with a jack or hoist, remove the insulator-to-engine bolts, and detach the insulator. Installation follows the reverse order of removal, using thread locking compound on the mount bolts and ensuring they are tightened securely. The right and left engine mounts are adjustable to allow drivetrain movement in relation to driveaxle assembly length, and adjustments should be made when servicing the driveaxles, after front end structural damage, or when replacing a mount. Remove the load on the engine mounts by carefully supporting the engine and transaxle assembly with a floor jack, then loosen the right insulator vertical fasteners and the front engine mount bracket-to-front crossmember bolts and nuts. The left engine mount insulator is sleeved over the shaft and long support bolt to provide lateral movement adjustment. Pry the engine right or left as required to achieve the proper driveaxle length, then securely tighten the right engine mount insulator vertical bolts, the front engine mount bolts and nuts, and center the left engine mount insulator. Finally, recheck the driveaxle length.