The behavior of concrete beams reinforced with steel and Glass Fiber Reinforced Polymer (GFRP) rebars, without shear reinforcement is investigated in the current study. This study includes testing experimentally of twenty-four steel and GFRP Reinforced Concrete (RC) beams cast with different percentage of fibers. The beams were split into two types, steel and GFRP RC beams. Beams of different fiber ratios (0, 0.5, 1.5 and 2.5%) were developed and tested, in two groups, each consists of twelve specimens, steel and GFRP reinforced RC beams. Both steel and GFRP RC beams were cast as singly reinforced with 10 mm diameter longitudinal bars at the bottom. In order to ensure that the beam to fail under shear, the top reinforcement and stirrups are removed. The concrete cover was kept as 30 mm. Three concrete grades (M30, M60 and M80) were examined for different dosage of fibers for both steel and GFRP RC beams. The size of the beam samples was kept as 150 ×200×1500 mm. The key parameters were the form of reinforcement material (steel and GFRP), compressive strength of concrete and fiber percentage. Failure mode, ultimate load carrying capacity, mid-span deflection, strain in concrete and reinforcement (steel and GFRP) of the beams have been reported. It is found that the effect of using fibers and higher grade of concrete is more pronounced in improving stiffness of GFRP RC beams compared to steel RC beams. Hence it can be concluded that GFRP rebars can be used as an efficient type of reinforcement in RC beams.

The present paper focuses on the practical application of software tools for calculating and verifying trusses systems. It covers externally and internally statically indeterminate trusses systems and compares results from two software tools. The MATLAB Simscape – Multibody simulation tool, specially designed for mechanical systems, is utilized to calculate the trusses system. The model is optimized to minimize errors compared to theoretical calculations. By using blocks, it is possible to build a system, including repeating parts quickly.

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

Steel fibres provides ductility to concrete structures. This in turn gives possibility to replace or reduce conventional reinforcement in structural elements. In this study the focus is on structural walls and the fibres as potential replacement for horizontal reinforcement in areas where vertical re-bars are needed. An experimental study was conducted, in which prismatic specimens with longitudinal re-bars were subjected to centric loading. Ten samples with 12 specimens in each were tested. The parameters considered were: fibre content, concrete cover for the longitudinal bars, and presence of stirrups. Self-compacting concrete with 30 and 60 kg/m3 steel fibres was used. The influence of fibres on maximum load, stiffness, and ductility of the specimens is evaluated. The results show that fibres eliminated brittle collapse and spalling of concrete at failure. Samples with fibres tend to have reduced maximum force and stiffness but increased ductility. The specimens with fibre content of 60 kg/m3 showed more ductile behaviour than the ones with minimum amount of conventional stirrups. The study suggests that combination of steel fibres and conventional re-bars can lead to less qualitative compactness of the self-compacting concrete, which in turn may reduce load bearing capacity and stiffness of the structure.

Full depth precast deck panel (FDDP) is one element of the prefabricated bridge element and systems (PBES) that allows for quick un-shored assembly of the bridge deck on-site as part of the accelerated bridge construction (ABC) technology. This paper investigates the structural response of full-depth precast deck panels (FDDPs) constructed with new construction materials and connection details. FDDP is cast with normal strength concrete (NSC) and reinforced with high modulus (HM) glass fiber reinforced polymer (GFRP) ribbed bars. The panel-to-girder V-shape connections use the shear pockets to accommodate the clustering of the shear connectors. A novel transverse connection between panels has been developed, featuring three distinct female-to-female joint configurations, each with 175-mm projected GFRP bars extending from the FDDP into the closure strip, complemented by a female vertical shear key and filled with cementitious materials. The ultra-high performance fiber reinforced concrete (UHPFRC) was selectively used to joint-fill the 200-mm transverse joint between adjacent precast panels and the shear pockets connecting the panels to the supporting girders to ensure full shear interaction. Two actual-size FDDP specimens for each type of the three developed joints were erected to perform fatigue tests under the footprint of the Canadian Highway Bridge Design Code (CHBDC) truck wheel loading. The FDDP had a 200-mm thickness, 2500-mm width, and 2400-mm length in traffic direction; the rest was over braced steel twin girders. Two types of fatigue tests were performed; incremental variable amplitude fatigue (VAF) loading and constant amplitude fatigue (CAF) loading, followed by monotonically loading the slab ultimate-to-collapse. It was observed that fatigue test results showed that the ultimate capacity of the slab under VAF loading or after 4 million cycles of CAF exceeds the factored design wheel load specified into the CHBDC. Also, punching shear failure mode was dominant in all the tested FDDP specimens.

We conducted the meander evolution experiments incorporating the effects of riparian vegetation and the series of upper vortex flow disturbances induced by a scour pit simultaneously. Two employed nonlegume plants with salinity and alkalinity resistance, had uniform degrees of seedling normal growth and different lengths of root networks. Our results show that riparian vegetation in general can consolidate the single-thread channel planform without branching outward under the flooding flow conditions. Transverse point bars on inner banks were instead by downstream scroll bars in overall channel for long, unless the coupling of riparian vegetation and flood scour. Shallow-rooted plant was inadequate to resist the inner-bank cutting effect brought by the upper vortex flow. Deep-rooted plant can stabilize the bank-lines and thalweg significantly, but that was susceptible to locally low vegetation coverage. Using evolutionary spectral analysis based on thalweg, we found streamwise high-frequency distribution of bed topography mainly concentrated downstream the bifurcation interface in unvegetated scenario when faced with a flood, shrank to the upper isolated turning interface in shallow-rooted scenario, and conversely stood out along the bare roots disturbed region in deep-rooted scenario. This experimental study expands a much wider understanding of vegetation effects in hydro-bio-geomorphological systems engineering.

Studies have shown that aerosols generated from flavored e-cigarettes contain Reactive Oxygen Species (ROS), promoting oxidative stress-induced damage within pulmonary cells. Our lab investigated the ROS content of e-cigarette vapor generated from disposable vape bars, a product exempt from the Federal Drug Enforcement Agency’s (FDA) 2020 flavor ban. Specifically, we analyzed vape bars belonging to multiple flavor categories (Tobacco, Minty Fruit, Fruity, Minty/Menthol, Desserts, and Drinks), manufactured by various vendors and of various nicotine concentrations (0-6.8%). Aerosols from these flavored vape bars were generated by a single puff aerosol generator and individually bubbled through a fluorogenic solution to detect and semi-quantify ROS in H2O2 equivalents generated by the vape bars. We compared and contrasted the ROS levels generated by each flavor as an indirect determinant of oxidative stress potential by these disposable vape bars. Our results showed that ROS concentration (μM) of aerosols produced from the vape bars varied significantly between different flavors and a function of nicotine concentration. Likewise, our results suggest that flavoring chemicals and nicotine concentration play a role in alerting ROS production in e-cigarette aerosols. Our study provides insight into the differential health effects of flavored disposable vape bars and the need for their regulation.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

This paper presents a new method to model the nonlinear behaviour of masonry double curvature structures, possibly reinforced by composite materials, by means of conventional elasto-plastic analyses. It is meant to be used in professional design, especially for assessment and retrofitting purposes, therefore based on the exploitation of the simplest nonlinear Finite Elements available in a commercial software, namely trusses with elasto-fragile and elasto-ductile behaviour (Cutoff Bars). The numerical static nonlinear analyses are carried out by considering elastic hexahedral elements for bricks and lumping nonlinearities on joints. These have been assumed in turn elastic-brittle and elastic-plastic by using 1D elements, respectively Point Contacts, under No-Tension Material hypothesis, and Cutoff Bars, assigning small tensile resistance to the material. The reinforcement, realised with FRP hooping strips, has been successfully modelled in a similar fashion, i.e. by applying perfectly bonded elastic-plastic Cutoff Bars at the extrados of the dome, where the debonding is accounted for in a conventional way limiting the tensile strength according to Italian Standards indications. The procedure is validated against benchmark models with the same geometry, using experimental data and more refined structural model results for comparison.