Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

Sweet sorghum is an important bioenergy grass and valuable forage with a strong adaptability to saline environments. However, little is known about the mechanisms of sweet sorghum coping with ion toxicity under salt stresses. Here, we first evaluated the salt tolerance of a sweet sorghum cultivar “Lvjuren” and determined its ion accumulation traits under NaCl treatments; then explored key genes involved in Na+, Cl−, K+ and NO3− transport using transcriptome profiling and qRT-PCR method. The results showed that the growth and photosynthesis of sweet sorghum were unaffected by 50 and 100 mM NaCl treatments, indicative of a strong tolerance of this species to salt stresses. Under NaCl treatments, sweet sorghum could efficiently exclude Na+ from shoots and accumulate Cl− in leaf sheaths to avoid their overaccumulation in leaf blades; meanwhile, it possessed a prominent ability to sustain NO3− homeostasis in leaf blades. Transcriptome profiling identified several differentially expressed genes associated with Na+, Cl−, K+ and NO3− transport in roots, leaf sheaths and leaf blades of sweet sorghum after 200 mM NaCl treatment for 6 and 48 h. Moreover, transcriptome data and qRT-PCR results indicated that HKT1;5, CLCc and NPF7.3-1 should be key genes involved in Na+ retention in roots, Cl− accumulation in leaf sheaths and maintenance of NO3− homeostasis in leaf blades, respectively. Many TFs were also identified after NaCl treatment, which should play important regulatory roles in salt tolerance of sweet sorghum. This work lays a preliminary foundation for clarifying the molecular basis underlying the adaptation of sweet sorghum to adverse environments.

In this study, literature on pore structure and chloride ion diffusivity was collected to investigate the correlation of pore structure indicators with diffusivity. Good correlation between total porosity and chloride ion diffusivity was found when the samples did not contain admixture materials and diffusion test was conducted without acceleration. Pore diameter indicators did not correlate with diffusivity. The diffusivity of cement paste was reduced by admixture materials compared to that without admixture materials even if the total porosity is the same. On the other hand, the diffusivity of concrete was not reduced by admixture materials.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

This study aimed to compare the differences in durability and prestress loss between normal-weight concrete (NC) and lightweight aggregate concrete (LWC) prestressed box girders, which were constructed at the same time in the same area, so as to verify the superiority of using synthetic lightweight aggregate (LWA) made from reservoir sediments in prestressed bridges. For the NCs and LWCs used in prestressed box girders, the basic mechanical properties were tested on the one hand, and the durability properties were tested on the other hand. Then, through the prestress monitoring system, the prestress loss of the two groups of the prestressed box girders was tracked. The results of the durability test confirmed that LWC can inhibit the penetration of air, water, and chloride ions by strengthening the interfacial transition zone between the aggregate and the cement paste, thereby improving its durability. Moreover, the magnetic flux prestress loss of the NC prestressed box girder reached 8.1%. In contrast, the magnetic flux prestress losses on both sides of the LWC prestressed box girder were 4.6% and 4.9%, respectively. This verified that, under the same environmental conditions, the use of LWC produced less of a prestress loss than the use of NC.

Feldspar which is one of the main inputs of the ceramic and glass industry has widespread resources in Turkey and holds an outstanding role in exportation. In addition to this, potassium feldspars are one of the suitable resources for the production of potash which is a vital component for agriculture industry. The chlorination technique was used to produce potassium chloride (KCl) from potassium feldspar ore in Kırşehir-Buzlukdağı region. The process of potassium chloride production was carried out with calcination process to decompose potassium feldspar and form potassium chloride while using different kinds of salts such as CaCl2, NaCl, and CaSO4 followed by water leaching process. The recovery from feldspar with 7.21% K2O content was obtained with the 1:1.25:1.5 ratio of Feldspar:CaSO4:NaCl at 1000 °C for 60 minutes followed by leaching. 96.08 % potassium dissolution was achieved.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of radio-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes were investigated. The main gas-phase and solid products of plasma-chemical transformations were determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems was carried out. It is shown that under the implemented experimental conditions, equilibrium components of the products are established. The detected spectra of chemical activity were studied, which gave reason to assume that the molecular mechanism of the hydrogen reduction process is the main one. The impurity composition of gas-phase and solid reaction products was investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, was shown.

The combustion of PVC cables in fires results in the release of hydrogen chloride gas. In the European Union, Regulation (EU) No 305/2011, in force since 2017, requires the classification of cables permanently installed in buildings for reaction to fire, smoke, flaming droplets, and acidity. The additional classification for acidity is evaluated through EN 60754-2, involving pH and conductivity measurements. This study focuses on the essential research and development of low-smoke acidity PVC compounds for cables, mainly aiming to meet the stringent additional classifications for acidity, a1 or a2, which cannot be achieved with traditional PVC cables. Understanding the chemistry of thermal decomposition and combustion, especially in the presence of hydrogen chloride scavengers, is crucial for meeting the best acidity classification. The article reviews the current tube furnace tests used in the European Union for cable halogen and acidity assessments. It discusses the limitations of the existing method (EN 60754-2) and highlights the potential of emerging tests such as IEC EN 60754-3, which employs ion chromatography for improved sensitivity and specificity. In the experimental part of the article, various standard and low-smoke acidity cable compounds are tested using tube furnace experiments with different heating regimes. The concentrations of cations and anions in solution are measured through ion chromatography and inductively coupled plasma–optical emission spectrometry. This detailed analysis aims to identify the species influencing pH and conductivity, which is crucial for designing effective acid scavengers that do not impact conductivity. The conclusive results emphasize that HCl from PVC thermal decomposition is the primary driver of pH and conductivity, and the contribution from the decomposition of additives and byproducts from combustion is found to be negligible in most of the tested PVC compounds for cables. The findings underscore the importance of understanding the thermal decomposition of PVC compounds to design acid scavengers capable of trapping hydrogen chloride without adversely impacting conductivity.

Background and Objectives: The ingestion of anhydrous calcium chloride (CaCl2) causes direct injury to the gastrointestinal wall via a thermal burn. Severe CaCl2 intoxication can induce a hypercalcemic crisis, presenting with arrhythmia, acute pancreatitis, and acute kidney injury. This case report details a patient with hematemesis and hypercalcemia following the ingestion of a commercial desiccant. We aimed to report the progression of the case and focused on the elec-trocardiographic manifestations. Case presentation: A 39-year-old female presented at a regional emergency center with blood in her vomit after the ingestion of a commercial desiccant. Bloody emesis was the initial symptom, and various electrolyte imbalances developed during admission. Electrocardiogram (ECG) changes occurred early after hospitalization and disappeared before the electrolyte levels normalized. The patient was maintained in an NPO state throughout her hospital stay. Bloody emesis and abdominal pain resolved rather early, despite her minimal mention of symptoms, possibly due to her suspected negative psychiatric symptoms. Conclusions: The rise in suicidal attempts has led to an increase in unusual intoxication cases. Previous reports on CaCl2 ingestion primarily considered the gastrointestinal injury. In this case, we observed the dynamic and prolonged multiple electrolyte imbalances along with the early-phase ECG changes, all of which responded well to supportive care. This report adds to the understanding of the diverse manifestations and management of CaCl2 intoxication.

Background. Traumatic brain injury (TBI) is the main cause of disabilities over the industrialized countries. Cognitive decline appears in the chronic phase of the pathology consecutively to cellular and molecular processes. Here we described the use of KCC2, a neuronal-specific potassium-chloride transporters as potent biomarker to predict cognitive dysfunctions after TBI. Methods. Using neuronal and total exosomes collection from blood serum in control and TBI subjects we were able to anticipate the decline of cognitive performance. Results. After TBI, we observed a significative and persistant loss of KCC2 expression in the blood exosomes that is correlated to changes in network activity and cellular processes such as secondary neurogenesis. Also we correlated this KCC2 loss in expression to the appearance of the cognitive decline observed in mice and more particularly we correlate the KCC2 loss of expression to the appearance of the depressive-like behavior. Conclusion. According to our protocol, we were able to confirm our previous findings in agreement with the potential therapeutic effect of bumetanide in the prevention of the post traumatic depression after TBI, by restoring the KCC2 expression thus preventing the massive neuronal death of interneurons and the secondary neurogenesis effect observed in such model.

Cyclic voltammetry can be applied as the reliable method for the determination of chloride ions in a range from several to couple hundred ppm. Since the standard potential of chloride ion/gaseous chlorine is 1.36 V vs NHE the efficient oxidation of Cl- ion occurs at very positive electrode potentials, usually higher than + 1.7 V vs NHE electrode. It is possible to observe this phenomenon only at noble-metal or inert carbon electrodes. Many other solutes, usually organic compounds, are often oxidized at this potential. This is the reason why determination of Cl- content directly from increase of the oxidation current is not reliable and can lead to overestimated values. However, gaseous chlorine, generated at positive potential dissolves in the analyzed solution and can be reduced in the reverse scan of cyclic voltammetric curve. Optimization of the experimental procedure using the statistical tools allowed for the development of the improved method for the direct quantification of chloride ions in acid copper electroplating baths. Under the proposed experimental conditions, the calibration curve (Cl2 voltammetric reduction current vs. chloride ions concentration) is represented by the linear model for the concentration of chlorides ranging from 10 to 200 mg/dm3.

Plastics have recently become an indispensable part of everyone's daily life due to their versatility, durability, light weight and low production costs. The increasing production and use of plastics poses a great danger due to the very long period of degradation, but also the negative impact on living organisms. Decomposing plastics lead to the formation of microplastics, which accumulate in the environment and living organisms becoming part of the food chain. Polyvinyl chloride (PVC) contamination of soil and water seriously threatens ecosystems around the world. The durability and low weight make microplastic particles easily transported with water or air and end up in the soil. Thus, the problem of microplastic pollution affects the entire ecosystem. Since microplastics are commonly found in both drinking and bottled water, humans are also exposed to the harmful effects of microplastics. Because of the existing risks associated with PVC microplastic contamination of the ecosystem, intensive research is underway to develop methods to clean and eliminate it from the environment. Pollution of the environment with plastic, especially microplastic, results in the reduction of both water and soil resources used for agricultural and utility purposes. This review provides an overview of PVC's environmental impact and disposal options.

Chloride (Cl-) is applied in coffee in rates as a “macronutrient” due that potassium (K+) is one of the most demanded nutrients by the coffee plant, and the potassium muriate (KCl) bases fertilizer is one the most used by the coffee growers. Does not exist scientific evidence that addresses the question regarding with which is the influences of the Cl- applied in the K fertilization base on MOP on coffee growth, nutrient uptake, and nitrogen use efficiency (NUE). Over four years, two trials were conducted on greenhouse and field conditions to address these questions. The trials set up were designed to test the influence of increased Cl- and reduced S rates on biomass accumulation, nutrient uptake, and NUE. A significant effect of the Cl- rates on growth was observed under greenhouse conditions but a non-significant effect on yield under field conditions. Cl- and S significantly influence the NUE in coffee. The result allows us to conclude that Cl- rates need to be balanced with S rates and that Cl- applied as a macronutrient can improve the NUE in coffee when those rates do not exceed 180 mg. L-1 Cl- and 80 mg.L-1 S in the greenhouse and 150 kg.ha-1.year-1 Cl- and 50 kg. ha-1.year-1 S in field conditions. In practical terms, coffee farmers need to balance the K base fertilizers sources to improve the nutrient use efficiency, especially the NUE.

Biocidal compositions based on interpolyelectrolyte complexes and a low molecular weight antibiotic can become a promising material for creating biocidal coatings, as they combine wash-off resistance and dual biocidal action due to the biocide and the polycation. Molecular mass characteristics of polymers play essential role in physics and mechanical properties of the coatings. In this work, the properties of polydiallyldimethylammonium chloride (PDADMAC) coatings of various molecular weights are investigated and assumptions are made about the optimal molecular weight needed to create antibacterial compositions. To study the resistance to washing off and moisture saturation of the coatings, the gravimetric method was used, the adhesive properties of the coatings were studied by dynamometry. It has been established that an increase in molecular weight affects the wash-off resistance of coatings, but does not affect moisture absorption and adhesion mechanics of coatings. All samples of PDADMAC were demonstrated to exhibit the same antibacterial activity. Thus, when developing systems for creating antibacterial coatings, it must be taken into account that in order to create stable coatings. The requirement to use PDADMAC with a high degree of polymerization is necessary for control the desorption of coating during wash off-but not mandatory for the control of mechanical and antibacterial properties of the coating.

Tough and antimicrobial dual-crosslinked poly((trimethylamino)ethyl methacrylate chloride)-phytic acid hydrogel (pTMAEMA-PA) has been synthesized by adding chemical crosslinker and docking physical crosslinker of multivalent phytic acid into a cationic polyelectrolyte network. By increasing the loading concentration of PA, the tough hydrogel exhibits compressive stress of >1 MPa, along with high elasticity and fatigue-resistant properties. The enhanced mechanical properties of pTMAEMA-PA were stem from multivalent ion effect of PA via the formation of ion bridges within polyelectrolytes. In addition, a comparative study for a series of pTMAEMA-counterion complexes was conducted to elaborate the relationship between swelling ratio and mechanical strength. The study also revealed secondary factors, such as ion valency, ion specificity and hydrogen bond formation, holding crucial roles in tuning mechanical properties of the polyelectrolyte hydrogel. Furthermore, in bacteria attachment and disk diffusion tests, pTMAEMA-PA exhibits superior fouling resistance and antibacterial capability. The results reflect the fact that PA enables chelating strongly with divalent metal ions, hence, disrupting the outer membrane of bacteria, as well as dysfunction of organelles, DNA and protein. Overall, the work demonstrated a novel strategy for preparation of tough polyelectrolyte with antibacterial capability via docking PA to open up the potential use of PA in medical application.

It is shown by numerical modelling that anisotropic diffusion can compensate and even overcome diffusion broadening - the main limiting factor of devices working at atmospheric pressure. The thickness of ion clouds coming out of the ionisation chamber is reduced ~ 1000 times in the ADMA inlet increasing the resolution. This finding has a great potential that enables construction of a device with resolution close to that of currently available desktop ion separation devices – high pressure mass spectrometers, but with much lower cost of manufacture and with smaller dimensions. Comprehensive numerical modelling along with mathematical analysis of physical concepts enables reduction of the footprint and manufacturing costs. Modelling determined that the resolving power (RP) potential of the ADMA is greater than the RP of currently available on the market devices for the airport security market. The ADMA technology enables very fast detection of threats; at least 100 times faster than currently used in Ion Mobility Spectrometers (IMS). This potentially allows an increase in passenger throughput in airports.

This paper introduces an open-source active high-precision signal amplifier designed for enhancing biodata acquisition, specifically focusing on EEG signals. The compact device, with a diameter of 18 mm, seamlessly integrates electronics, signal processing, and meticulous design considerations. Incorporated within the single board are circuits for low-noise amplification, an analog interface equipped with bandpass filters, and an integrated ADC for precise digitization. A comprehensive evaluation of signal quality has been conducted, encompassing aspects such as noise levels, electrode bias tolerance, and common mode rejection ratio. To facilitate this evaluation, the widely recognized Silver Chloride electrode (Ag/AgCl) has been employed. Additionally, this paper delves into an extensive discussion concerning diverse sources of noise, along with strategies to curtail input noise and minimize noise originating from electrodes and amplifiers. Leveraging the substantial advancements achieved in the design of dry contact electrodes, this specific device is poised to carve a notable niche in the realm of brain-computer interface.

A study of cryogenic drilling in sandwich composites has been carried out. Materials used have been carbon fiber reinforced polymer sandwich sheets with inner foamed polyvinyl chloride core, composites with aerospace, marine, construction and automotive applications, including protec-tion structure of Polar engineering equipment. Experimental tests have been performed in lam-inates with 12 mm and 6 mm of thickness, drilling with liquid nitrogen as refrigerant to reach temperatures below -120ºC under different cutting conditions, in particular, drill rotation speeds between 2000 rpm and 6000 rpm and feed rates between 200 mm/min and 600 mm/min. Variables as thrust forces and circularity error have been measured, due to the importance of its effect on the hole quality, as an operation prior to a possible assembly. A design of experiments has been allowed determining relationships between variables, identifying the influence of cutting condi-tions on the thrust force and the circularity at inlet and outlet holes.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

Seed germination is the most sensitive stage to abiotic stress, including salt stress (SS). SS affects plant growth and performance through ion toxicity, decreases seed germination percentage, and increases the germination time. Several priming treatments were used to enhance germination under SS. The objectives of this study are to 1) identify priming treatments to shorten the emergence period; 2) evaluate priming treatments against the SS; 3) induce synchronized seed germination. Salt-sensitive “Burpee bibb’ lettuce seeds were treated with 0.05% Potassium nitrate, 3 mM Gibberellic acid, and distilled water (HP). All the primed and non-primed seeds were subjected to 100 mM NaCl or 0 mM NaCl. The 7-day experiment arranged in a complete randomized block design with four replications was conducted in a growth chamber maintained with 16/8 h photoperiod (light/dark), 60% relative humidity, and day/night temperature of 22/18 °C. The result indicated that HP seeds were better synchronized under SS. Similarly, FM and DM of cotyledon, hypocotyl, and radicle were highest in HP lettuce regardless of SS. Electrolyte leakage was the lowest in the HP lettuce, while other priming methods under SS increased membrane permeability leading to osmotic stress and tissue damage. Overall, the HP can be a suitable priming method to synchronize germination and increase FM and DM by creating the least osmotic stress and ion toxicity in lettuce under SS.

As a hazardous waste, pickling waste liquor must be properly treated. An alternative consists in promoting the formation of ferrous salts from this residue, due to its higher ferrous content. Since FeCl2·4H2O is widely used in several applications, obtaining pure crystals of this material appears to be an interesting prospect. However, this compound has scarcely been investigated. In the present work, FeCl2·4H2O crystals have been obtained from pickling waste liquors. Their structural and morphological characteristics have been investigated by X-ray diffraction, scanning electron microscopy as well as Mössbauer spectroscopy. In addition, the photoluminescence study of the obtained samples was also assessed. It was observed that after some aging time, the obtained crystals change in colour from green to more yellowish. So, the aged sample has also been evaluated, and their structural characteristics are compared with the original crystals. Despite this, the obtained crystals exhibit a FeCl2·4H2O structure, which is not modified with the aging of the sample.

There are experimental evidences that chronic social defeat stress is accompanied by development of anxiety- and depression-like state as well as downregulation of serotonergic genes in the midbrain raphe nuclei of male mice. The study was aimed at investigating the effect of chronic lithium chloride (LiCl) administrations on anxiety behavior and the expression of serotonergic genes in the midbrain raphe nuclei of affected mice. The pronounced anxiety in male mice was caused by chronic social defeat stress in daily agonistic interactions. After 6 days of social stress, defeated mice were treated with saline or LiCl (100 mg/kg, i.p. two weeks) against the background of continuing agonistic interactions. The level of anxiety was assessed using behavioral tests. The effect of chronic treatment with LiCl on the expression of serotonergic genes in the midbrain rapher nuclei was also studied. Mild anxiolytic effects of LiCl were found on communication in the partition test. Anxiogenic-like effects assessed using the elevated plus-maze and social interaction tests were found. Chronic LiCl treatment induced overexpression of the serotonergic genes in the midbrain raphe nuclei. The effects of chronic LiCl treatment depends on the method of treatment, psychoemotional state, and experimental context (tests).

Cationised hemp cellulose was prepared by etherification with two quaternary ammonium salts: 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CHPTAC) and glycidyltrimethylammonium chloride (GTMAC) and examined for (i) the efficiency of Cr(VI) removal under acid mine-drainage (AMD) conditions, and (ii) antibacterial activity. Adsorbents were characterised by electron microscopy, Fourier transform infrared (FTIR), CP-MAS ¹³C nuclear magnetic resonance (NMR) spectroscopy, elemental composition and surface charge. FTIR and solid state ¹³C NMR confirmed the introduction of quaternary ammonium moieties on cellulose. ¹³C NMR also showed that cationisation decreased the degree of crystallisation and lateral dimensions of cellulose fibrils. Nevertheless, 47 % - 72% of Cr(VI) ions were removed from solutions at pH 4, by 0.1 g of CHPTAC and GTMAC-cationised cellulose, respectively. Adsorption kinetics followed the pseudo-second order model and isotherms were best described by the Freundlich and Dubinin-Radushkevich models. When GTMAC-modified cellulose was applied to AMD contaminated water (pH 2.7), however, Cr(VI) uptake removal decreased to 22% likely due to competition from Al and Fe ions. Nevertheless, cationised materials displayed considerable antibacterial effects, reducing the viability of Escherichia coli by up to 45 % after just 3 hours of exposure. Together, these results suggest that cationised cellulose can be applied in the treatment of Cr(VI)-contaminated mine water particularly if pre-treatments to reduce Fe and Al concentrations are applied.

An experimental platform for laser-driven ion (sub-MeV) acceleration and potential applications was recently commissioned at the HiLASE laser facility. The auxiliary beam of the Bivoj laser system operating at GW peak power (~10 J in 5-10 ns) and 1-10 Hz repetition rate enabled a sta-ble production of high-current ion beams of multiple species (Al, Ti, Fe, Si, Cu, Sn). The pro-duced laser-plasma ion sources were fully characterized against the laser intensity on target (1013-1015 W/cm2) by varying the laser energy, focal spot size, and pulse duration. This al-lowed to provide accurate scaling laws of the maximum ion energy for the different target ma-terials investigated. Such experimental scaling laws are presented for the first time in the inves-tigated laser intensity range and for ns-class laser pulses, and allow to provide a qualitative in-terpretation of the laser-plasma interaction underpinning physics, thus to tune the main features of the accelerated ion beams (energy, temperature, and current). Such a detailed study was facil-itated by the large amount of data acquired at high repetition rate (1-10 Hz) provided by the Bivoj laser system. The versatility and tuneability of such high-repetition-rate laser-plasma ion sources are of po-tential interest for multidisciplinary user applications.

A model for the simulation of ion beam extraction from an electron cyclotron resonance ion source is proposed. It is based on the simple fact that charged particles follow magnetic field lines. Therefore magnetic field lines are used to generate initial conditions for ray-tracing. This model reproduces in simulation experimentally obtained results. The importance of correlations in phase-space caused by the magnetic field is shown in simulation. This model also describes the physics of space-charge and its compensation in the extracted (fast) ion beam by low energy electrons. Simulation provides the possibility to test theoretical assumptions, as well as to optimize technical designs.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

The corrosion inhibition behavior of cetyl pyridinium chloride (CPC) on mild steel (MS) in 0.5 M H₂SO₄ solution was examined using the weight loss method and potentiodynamic polarization method. The experimented MS surface was characterized by Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Atomic Force Microscopy (AFM). Corrosion rate and corrosion efficiency was calsulated via weight loss and potentiodynamic polarization methods where the corrosion rate in 0.5 M H₂SO₄ , 0.000192 M, and 0.0077 M of CPC solution was 12.09×10^-3, 8.23×10^-3, 6.63×10^-5 (mm/Year), respectively and the inhibition efficiency of 94.42% and 98.54%. FESEM studies demonstrated the corrosion attack on MS surface. Also, the EDX showed the presence of nitrogen of CPC. Thus, CPC acts as an important corrosion inhibitor.

Thoracic aortic aneurysm (TAA) has a prevalence of 0.16%-0.34% and an incidence of 7.6 per 100,000 person-years, accounting for 1%-2% of all deaths in Western countries. Currently, no effective pharmacological therapies have been identified to slow TAA development and prevent TAA rupture. Large TAAs are treated with open surgical repair and less invasive thoracic endovascular aortic repair, both of which have high perioperative mortality risk. Therefore, there is an urgent medical need to identify the cellular and molecular mechanisms underlying TAA development and rupture to develop new therapies. In this review, we summarize animal TAA models including recent developments in porcine and zebrafish models: porcine models can assess new therapeutic devices or intervention strategies in a large mammal and zebrafish models can employ large-scale small-molecule suppressor screening in microwells. The second part of the review covers current views of TAA pathogenesis, with a focus on the roles of the transforming growth factor-beta (TGFβ) pathway and the vascular smooth muscle cell (VSMC)-elastin-contractile unit. The last part discusses TAA treatment options as they emerge from recent preclinical studies.

Li3FeN2 material was synthesized by two-step solid-state method from Li3N (adiabatic camera) and FeN2 (tube furnace) powders. Phase investigation of Li3N, FeN2 and Li3FeN2 were carried out. Discharge capacity of Li3FeN2 is 343 mAh g-1, that is about 44.7% of theoretic capacity. The molar heat capacity of Li3FeN2 at constant pressure in the temperature range 298-900 K should be calculated as Cp,m = 77,831 + 0,130 × T – 6,289 × T-2, where T is absolute temperature, . Thermodynamic characteristics of Li3FeN2 were determined as next: entropy S0298 = 116.2 J mol-1 K-1, molar enthalpy of dissolution ΔdHLFN = ˗ 206,537 ± 2,8 kJ mol−1, the standard enthalpy of formation ΔfH0 = ˗ 291.331 ± 5.7 kJ mol−1, entropy S0298 = 113.2 J mol-1 K-1 (Neumann-Kopp rule) and 116.2 J mol-1 K-1 (W.Herz rule), the standard Gibbs free energy of formation ∆f G0298 = ˗276,7 kJ mol-1.

Accurate prediction of the membrane potential by membrane theory is possible on the basis that the plasma membrane is selectively permeable to ions and that permeability determines the characteristics of the membrane potential. However, an experimental and artificial cell system with an impermeable membrane serving as a model plasma membrane has a non-zero membrane potential, and this potential generated across the membrane is somehow consistent with the potential characteristics predicted by the membrane theory, despite the impermeability of the membrane to ions. A long-forgotten theory, called the association-induction hypothesis (AIH), has emerged as a more plausible mechanism for generating the membrane potential than the membrane theory to explain this unexpected behavior. The AIH asserts that ion-selective membrane permeability is not necessary for the generation of the membrane potential, which is contrary to the membrane theory. Although such an idea is not easy to accept, the experimental results clearly suggest the correctness of the AIH.

With a longer-term goal of addressing the comparative behavior of the aqueous halides F$^-$, Cl$^-$, Br$^-$, and I$^-$ on the basis of quasi-chemical theory (QCT), here we study structures and free energies of hydration clusters for those anions. We confirm that energetically optimal $(\mathrm{H_2O})_n\mathrm{X}$ clusters, with X = Cl$^-$, Br$^-$, and I$^-$, exhibit \emph{surface} hydration structures. Computed free energies based on optimized surface hydration structures utilizing a harmonic approximation, typically (but not always) disagree with experimental free energies. To remedy the harmonic approximation, we utilize single-point electronic structure calculations on cluster geometries sampled from an AIMD (\emph{ab initio} molecular dynamics) simulation stream. This \emph{rough-landscape} procedure is broadly satisfactory and suggests unfavorable ligand crowding as the physical effect corrected. Nevertheless, this procedure can break down when $n \gtrsim 4$, with the characteristic discrepancy resulting from a relaxed definition of clustering in the identification of $(\mathrm{H_2O})_n\mathrm{X}$ clusters, including ramified structures natural in \emph{physical cluster theories.} With ramified structures, the central equation for the present rough-landscape approach can acquire some inconsistency. Extension of these physical cluster theories in the direction of QCT should remedy that issue, and should be the next step in this research direction.

A novel concept of ion separation Anisotropic Diffusion Mobility Analyser (ADMA) with Individual Ion Counter (IIC) was shown by numerical modelling to be able to separate ions with high resolution and ultra-high sensitivity. An ADMA-IIC device has been developed and tested at sheath flow rates below 40 l/min with a number of chemicals relevant to airport security and military applications. The resolving power of the ADMA was observed to be in the range of 40 to 80. These data were close to the resolution obtained in numerical modelling predictions. It is greater than or comparable with the RP of currently available on-the-market devices for airport security and other applications. It was also confirmed that the ADMA technology enables very fast detection of analytes, at least 100 times faster than ion mobility spectrometers. It was shown that Brownian diffusion can be controlled and even overpowered by generating highly anisotropic diffusion in the ADMA device. The ultimate sensitivity of single-ion detection below the ppq range has been demonstrated.

Little has been written in literature about the clinical comparison of the single use of chlorhexidine (CHX) rather than its combination with cetylpyridinium chloride (CPC). The purpose of this study was to compare the clinical effectiveness of two at-home antiseptic regimens. Healthy subjects scheduled for dental surgery were enrolled. After the surgery, patients were randomly allocated in a first group (Group A) which received a manual ultra soft toothbrush (Mentadent Professional®), an antiseptic toothpaste with 0,12% CHX and Vitamin B3 (Mentadent Professional Azione Intensiva Gengive®) and an antiseptic mouthwash with 0,12% CHX and 0,07% CPC. The second group (Group B) received solely an antiseptic mouthwash with 0,2% in conjunction with Anti Discoloration System (Curasept ADS/DNA®) and were encouraged to use their usual toothbrush and toothpaste. Patients were instructed to use the products twice a day and to rinse for 30 seconds. On day 7, patients were examined for the Early Healing Score, Visual Plaque Index of the sutures, Numerical Rating Scale and mouthwash taste. Group A showed a statistically significant levels of EHS and taste satisfaction. The regimen based on CHX associate with vitamin B3 in the toothpaste and CPC in the mouthwash resulted in superior clinical outcomes and satisfaction compared to solely CHX.

Background: The purpuse was to investigate the influence induced by magnesium chloride (MgCl2) and zinc gluconate (ZnG) supplementation on liver and kidney injuries experimentally-induced with acetaminophen (AAPh) and potentiated by ciprofloxacin addition in rats. Material and methods: The experiment was performed on 5 animals groups: group 1 – control, treated for 6 weeks with normal saline, 1mL/kg; group 2 – AAPh, treated for 6 weeks with AAPh, 100 mg/ kg/day; group 3 – AAPh+C, treated AAPh 100 mg/kg/ day for 6 weeks and ciprofloxacin, 50mg /kg/day, only in the last 14 days of the experiment; group 4 – AAPh+C+Mg, with the same treatment as group 3, but, and in the last 14 days, MgCl2 10 mg/ kg/day was added; group 5 – AAPh+C+Zn, with the same treatment as group 3, but, and in the last 14 days, zinc gluconate (ZnG),10 mg/kg/day was added. All administrations were performed by oral gavage. At the end of the experiment, the animals were sacrificed and blood samples were collected for biochemistry examinations. Results: Treatment with AAPh for 6 weeks determined an alteration of the liver function (increases in alanine aminotransferase, aspartate aminotransferase, lactic dehydrogenase and, and gamma-glutamyl transferase) and of renal function (increases in serum urea and creatinine) (P < 0.001 group 2 vs. group 1 for all mentioned parameters). Also, the antioxidant defense capacity was impaired in group 2 vs. group 1 (superoxide dismutase and glutathione peroxidase activity decreased in group 2 vs. group 1, 0.001 < P < 0.01, respectively 0.01 < P < 0.05). The addition of ciprofloxacin, 50 mg/kg/day during the last 14 days resulted in further increases in alkaline phosphatase, alanine aminotransferase, aspartate aminotransferase, urea and creatinine (0.01 < P < 0.05, group 3 vs. group 2). MgCl2 provided a slight protection against liver enzymes increase and a more pronounced protection against the increase in serum urea and creatinine (0.001 < P < 0.01 group 4 vs. group 3). MgCl2 provided a slight protection against the decrease in superoxide dismutase (0.01 < P < 0.05 group 4 vs. group 3), but not against decrease of glutathione peroxidase. The improvement of mentioned parameters could also be seen in case of ZnG, to a higher extent especially in the case of alanine aminotransferase and lactic dehydrogenase (0.01 < P < 0.05 group 5 vs. group 4). Conclusions: This study represents a furthermore proof for beneficial effect of magnesium and zinc salts against toxicity induced by different agents, including antibacterials added to the analgesic and antipyretic acetaminophen; the protection is proven on the liver and kidney’s function; the antioxidant profile improvement has a key role, especially in case of zinc gluconate.

Soil nitrite (NO2‒) is an important reactive intermediate in many nitrogen transformation processes, but it is unstable under acidic conditions. Canonical extraction method of soil NO2‒ with potassium chloride (KCl) solution greatly underestimates its concentration. In order to reflect the concentration more accurately, we optimized the extraction method of soil NO2‒ in this study. Moreover, soil ammonium (NH4+) and nitrate (NO3‒) were also systematically investigated to achieve efficient extraction of soil inorganic nitrogen. The results showed that un-buffered KCl significantly underestimated soil NO2‒ concentration compared to DIW. The highest recovery of NO2‒ was obtained by extracting with DIW at 10 min of oscillation for three soils. Compared with DIW, the concentration of NH4+ and NO3‒ in soil extracted from KCl solution increased significantly. Furthermore, the soil inorganic nitrogen content of extracts stored at 4°C for one day were closer to directly measurements of fresh samples than the other storage methods. Overall, the recommend analysis method for soil NO2‒ was extracted by DIW, oscillated for 10 min, and filtered by a 0.45 µm filter, and soil NH4+ and NO3‒ were extracted with KCl solution and oscillated for 30 min. The extract should be stored at 4°C and analyzed within 24 hours.

Thirty-six healthy 21-day-old weaned ternary piglets (Duroc × Landrace × Yorkshire) were randomly divided into 2 treatments with 18 replicates per treatment and 1 pig per replicate. The control group was fed with basal diet and the test group was fed with diets supplemented with 1 kg/t tea residue. The test period was 28 days. The results are as follows: The addition of tea residue in the diet has no significant effect on the growth performance of weaned piglets (P > 0.05), but it could significantly reduce the diarrhea rate of piglets from 1 to 7 days and 1 to 28 days (P < 0.05). Compared with the control group, the dietary supplementation of tea residue had no significant effect on nutrient apparent digestibility, plasma biochemical indexes and plasma immune indexes (P > 0.05), but increased the content of glutathione in plasma (P < 0.05). Tea residue had no significant effect on the morphology of jejunum and ileum of piglets (P > 0.05), but it could significantly reduce the content of chloride ion in feces (P < 0.05). Compared with the basal diet group, there was no significant difference in the relative expression of TMEM16A and CFTR mRNA in the colon of weaned piglets (P > 0.05). The whole-cell patch clamp recording showed that the TMEM16A and CFTR ion channels could be activated by ionomycin and forskolin, respectively. However, when the HT-29 cells transfected with TMEM16A and CFTR channels were treated with tea residue extract, it could significantly inhibit the chloride current of the TMEM16A and CFTR ion channels (P < 0.05).

In this research, a novel collector cetyl trimethyl ammonium chloride (CTAC) was used to separate hematite from quartz via reverse flotation for the first time. Micro-flotation tests showed that CTAC had a strong ability to selectively collect quartz and a separation of hematite from quartz could be accomplished with a concentration of 0.00263 mmol/L CTAC. Zeta-potential measurements indicated that the positive CTAC+ species could selectively increase the surface potential of quartz, but it had rather a weak effect on the hematite surface. X-ray photoelectron spectroscopy (XPS) detection indicated that CTAC had a stronger binding affinity to oxygen sites on the surface of quartz than that of hematite, resulting in a large amount of CTAC predominantly adsorbed on quartz rather than hematite.

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of concrete durability during the concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. Electrical resistivity of concrete is important to estimate two processes involved in corrosion of reinforcement: initiation (chloride penetration) and propagation (corrosion rate). The resistivity of concrete structure exposed to chloride indicates the risk of early corrosion damage, because a low resistivity is related to rapid chloride penetration and to high corrosion rate. Concrete resistivity is a geometry-independent material property that describes the electrical resistance, which is the ratio between applied voltage and resulting current in a unit cell. The current is carried by ions dissolved in the pore liquid. While some data exist on the relationship between moisture content on electrical resistivity of concrete, very little research has been conducted to evaluate the effect of chloride on the conduction of electricity through concrete. The purpose of this study is to examine and quantify the effect of pore water and chloride content on surface electrical resistivity measurement of concrete. It was obvious that chloride content had influenced the resistivity of concrete and the relationship showed a linear function. That is, concrete with chloride ions had a comparatively lower resistivity. Chloride can lead to underestimate the electrical resistivity of concrete. Conclusively, this paper suggested the quantitative solution to depict the electrical resistivity of concrete with various chloride contents.

Strained layer superlattice (SLS) material system is being considered for large format, small-pitch and low-cost focal plane arrays for different applications. To address difficulties associated to focal plane arrays fabrication arising from mesa-isolation etching or complex surface treatment/ passivation process, planar structures have been considered. In this work, the recent progress on planar SLS photodetector using ion-implantation for device isolation is presented. The devices are presented here are nBn and pBn heterostructure InAs/InAsSb SLS photodetector, where Zn and Si were chosen as the ion implants, respectively. The electrical and optical performance of the devices were compared along with comparison with mesa-etched device, to give deeper view of the device performance.

Li₇La₃Zr₂O₁₂Solid-state reaction was used for Li₇La₃Zr₂O₁₂ material synthesis from Li₂CO₃, La₂O₃ and ZrO₂ powders. Phase investigation by XRD, SEM and EDS methods of Li₇La₃Zr₂O₁₂ were carried out. The molar heat capacity of Li₇La₃Zr₂O₁₂ at constant pressure in the temperature range 298-800 K should be calculated as Cp,m = 518.135+0.599 × T - 8.339 × T−2, where T is absolute temperature, . Thermodynamic characteristics of Li₇La₃Zr₂O₁₂ were determined as next: entropy S0298 = 362.3 J mol-1 K-1, molar enthalpy of dissolution ΔdHLlZO = ˗ 1471.73 ± 29.39 kJ mol−1, the standard enthalpy of formation from elements ΔfH0 = ˗ 9327.65 ± 7.9 kJ mol−1, the standard Gibbs free energy of formation ∆f G0298 = ˗9435.6 kJ mol-1.

An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

Today, contamination from heavy metals in the atmosphere is a global concern. Efficient detection techniques are therefore necessary if heavy metal exposure levels in different media are to be determined. The voltammetry method for in situ detection of heavy metal ions is a very sensitive electrochemical method. This thesis explores emerging developments in electrode alteration, materials production and experimental optimization. An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

The potassium-chloride cotransporter KCC2 is the main extruder of Cl- in neurons. It plays a fundamental role in the activity of the inhibitory neurotransmitters (GABA and glycine) since low levels of KCC2 promote intracellular Cl- accumulation leading to a depolarizing activity of GABA and glycine. Downregulation of this cotransporter occurs in neurological disorders characterized by hyperexcitability, such as epilepsy, neuropathic pain and spasticity. KCC2 is also downregulated after axotomy. If muscle reinnervation is allowed, KCC2 levels recover in motoneurons. Therefore, we argued that target-derived neurotrophic factors might be involved in the regulation of KCC2 expression. For this purpose, we performed the axotomy of extraocular motoneurons by monocular enucleation of adult rats, and a pellet containing either VEGF or BDNF was chronically implanted in the orbit. Double confocal immunofluorescence of ChAT and KCC2 was carried out in brainstem sections. Axotomy led to a KCC2 decrease in the neuropil and soma of extraocular motoneurons, peaking at 15 days post-lesion, with the exception of abducens motoneuron somata. VEGF administration prevented the axotomy-induced KCC2 downregulation. By contrast, BDNF either maintained or reduced KCC2 levels following axotomy suggesting BDNF is involved in the axotomy-induced KCC2 downregulation in extraocular motoneurons. The finding that VEGF prevents KCC2 decrease opens new possibilities for the treatment of neurological disorders coursing with neuronal hyperactivity due to KCC2 downregulation.

Background/Objectives: Listeria monocytogenes is a foodborne pathogen that can infect humans and animals, causing non-invasive gastrointestinal listeriosis or invasive listeriosis. The objectives of this study were to determine: the genetic diversity of L. monocytogenes; the genes associated with the resistance to antibiotics, benzalkonium chloride (BC), and CdCl₂, and biofilm formation. Methods: Seventeen strains of L. monocytogenes isolated fresh fruits and vegetables were selected for this study. Genetic diversity and the genes associated with antibiotic resistance were determined by PCR amplification. Susceptibility to antibiotics were determined using the agar diffusion method. Resistance to BC and CdCl₂ was determined using the minimum inhibitory concentration method. Capacity for biofilm formation was evaluated using the crystal violet staining method. Results: This study demonstrates that the isolates of L. monocytogenes belong to serotypes 1/2a (29.4%) and 1/2b (70.5%). Potential hypervirulent strains containing 70.5% Listeria pathogenicity island 1 (LIPI-1-2), 17.6% (LIPI-1-3), and 11.7% (LIPI-1-4) were also identified. Antibiotic susceptibility tests show that L. monocytogenes exhibit six different multiresistant patterns with a MAR index of ³ 0.46 (70.5%); besides, the gen Ide, tetM, and msrA were detected in 52.9%, 29.4%, and 17.6%, respectively, associated with efflux pump Lde, tetracycline and ciprofloxacin resistance. Phenotypic test shows that 58.8% cadmium-resistant L. monocytogenes have a co-resistance to BC of 23.5%. Subsequently, all strains of L. monocytogenes exhibited moderate biofilm. Conclusions: This study contributes to the persistence and genetic diversity of strains L. monocytogenes isolated fresh fruits and vegetables; in addition, resistance to CdCl₂ and correlation with co-resistance to BC disinfectant used in the food industry.

Electrolyte disturbances are common in patients with traumatic brain injury (TBI), particularly affecting sodium, potassium, chloride and calcium levels. This study aims to provide insights into these disturbances within the first 24 hours post-injury. We conducted a cross-sectional analysis of 50 TBI patients, excluding those with conditions affecting electrolyte balance. Electrolyte levels were measured, and correlations with demographic data, trauma mechanisms, imaging findings, and Glasgow Coma Scale (GCS) scores were analyzed. Results indicated that chloride levels inversely correlated with GCS scores (ρ = -0.515; p = 0.002), suggesting that elevated chloride may indicate severe neurological impairment. Potassium levels were significantly associated with subdural hematoma (p = 0.032) and subarachnoid hemorrhage (p = 0.043), highlighting their potential as markers for severe brain injuries. No significant associations were found between sodium or calcium levels and the studied variables. These findings underscore the importance of early monitoring of chloride and potassium levels in TBI patients to improve management and outcomes. Future research should focus on larger, multi-center studies to validate these findings and develop comprehensive guidelines for managing electrolyte imbalances in TBI patients.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

Modern engineering faces challenges in ensuring technical standards for service, durability, and sustainability. Political, administrative, and budgetary factors, coupled with climate change, pose tasks to structural integrity, affecting industries and economies. Marine infrastructures represent a strategic asset of the country as it handles a large part of the economic exchanges. This article analyzes five essential factors that play a fundamental role in the performance analysis of coastal structures: Chloride-induced corrosion, degradation models, maintenance strategies, monitoring, and climate change. Starting with reinforcement corrosion, considered as the main cause of distress, particularly in coastal zones for the long-term behavior of structures. Additional pressure from the influences of climate change is becoming evident and extreme, leading to reduction in capacity. To guarantee the lifespan, degradation models contribute by estimating the long-term performance of the asset as a strategic piece to the development of effective maintenance solutions. Additionally, quantifying the condition of the structure from monitoring data, plays a crucial part that provides information on the current situation of the structure. Finally, this review summarizes the challenges associated with the maintenance of aging marine structures considering aspects such as corrosion, monitoring, and the future challenges this area will face due to climate change.

Under the dual erosion conditions of the dry-wet cycle, which is caused by the high chloride salt concentrations in mine water and fluctuations in mine water level, cemented paste backfill (CPB) suffers serious damage and deterioration. To discuss the mechanical properties and permeability characteristics of CPB under erosion, this study designs an immersion experiment for CPB under chloride salt and dry-wet cycle conditions. Through a uniaxial compressive strength (UCS) test, the change law for the mechanical parameters of the CPB was explored, strength constitutive equation of the CPB was constructed, and the process of deterioration of the CPB was analyzed. Through the penetration test, the diffusion characteristics of packing under chloride salt and dry-wet cycle conditions were explored. The results demonstrated that the strength and elastic modulus of the CPB first increased and then decreased rapidly, with maximum decrease rates of 32.2% and 38.2%, respectively. The CPB structure presents an initial non-damage stage, initial damage stage, damage development stage, damage destruction, and residual damage stage. The chloride ion penetration depth gradually increased with an increase in the number of dry-wet cycles, with a maximum diffusion depth of 20.5 mm. The maximum apparent diffusion coefficient of chloride ion was 18.99×10-10m2/s, and the maximum concentration was 0.303 mol/L. Under the double erosion conditions due to chloride salt and dry-wet cycle, the CPB structure is seriously damaged.

High concentrations of sodium (Na+), chloride (Cl-), calcium (Ca2+), and sulphate (SO42-) are fre-quently found in saline soils. Crop plants cannot successfully develop and produce because salt stress impairs the uptake of calcium, potassium, and water into plant cells. Different intracellular and extracellular ionic concentration changes by salinity, including those of calcium, potassium, and protons. These cations serve as stress signaling molecules in addition to being essential for ionic homeostasis and nutrition. Maintaining an appropriate K+: Na+ ratio is one crucial plant mechanism for salt tolerance, which is a complicated trait. Another important mechanism is the ability for fast extrusion of Na+ from the cytosol. Calcium is established as a ubiquitous secondary messenger, which transmits various stress signals into metabolic alterations that cause adaptive responses. When plants are under stress, the cytosolic-free Ca2+ concentration can rise to 10 times or more from its resting level of 50-100 nanomolar. Reactive oxygen species (ROS) are linked to the calcium alterations, and are produced by stress. Depending on the type, frequency and intensity of the stress, the cytosolic calcium signals oscillate, are transient, or persist for a longer period and exhibit specific "signatures". Both the input and efflux of Ca2+ from the cytosol affect the length and amplitude of the signal. According to several reports, under stress calcium alterations can occur not only in the cytoplasm of the cell but also in the cell walls, nucleus and other cell organelles and the calcium waves propagate through the whole plant. Here, we will focus on how wheat and other important crops absorb Na+, K+ and Cl- when plants are under salt stress, as well as how calcium, potassium, and pH cause intracellular signaling and homeostasis. Similar mechanisms in the model plant Arabidopsis will also be considered.

A wide variety of substances have been used to anaesthetise invertebrates, but many are not anaesthetics and merely incapacitate animals, rather than preventing pain. Much is now known about the mode of action of modern clinical and veterinary anaesthetics because of their use on human beings and other vertebrates. In essence, the role of an ideal general anaesthetic is to act as a muscle relaxant, an analgesic, an anaesthetic and an amnesic. To achieve all these properties with a single substance is difficult and various adjuvants usually need to be administered, resulting in a cocktail of drugs. In a clinical setting, the vast majority of patients are unaware of surgery being carried out and have no memory of it, so they can claim to have felt no pain, but this is much more difficult to demonstrate in invertebrates. Here we show that 1% MgCl2, a muscle relaxant, is a useful adjuvant for the clinical anaesthetic isoflurane on Octopus vulgaris when applied for 10 minutes before the clinical anaesthetic. After this, full anaesthesia can be achieved in 5 minutes using only 1% isoflurane and from which full recovery takes place rapidly in about 10 to 15 minutes. This reduces stress on the animal and minimises the quantity of anaesthetic used.

Deep eutectic solvents (DESs) have emerged as novel alternatives to common solvents and VOCs. Their employment as electrolytes in battery has been an area of intense research. In this context, understanding changes in physicochemical properties of DESs in the presence of Li salts becomes of utmost importance. Solvatochromic probes have potential to gauze such changes. It is reported herein that one such uv-vis molecular absorbance probe, Reichardt’s betaine dye 33, effectively manifests changes taking place in a DES Glyceline, composed of H-bond accepting salt choline chloride and H-bond donor glycerol in 1 : 2 molar ratio, as salt LiCl is added. Lowest energy intramolecular charge-transfer absorbance band of this dye exhibits 17 nm hypsochromic shift as up to 3.0 molal LiCl is added to Glyceline. The estimated ETN parameter shows linear increase with LiCl mole fraction. Spectroscopic responses of betaine dye 33, N,N-diethyl-4-nitroaniline and 4-nitroaniline are used to assess empirical Kamlet-Taft parameters of dipolarity/polarizability (π*), H-bond donating acidity (α) and H-bond accepting basicity (β) as a function of LiCl concentration in Glyceline. LiCl addition to Glyceline results in increase in α and no change in π*and β. It is proposed that added lithium interacts with oxygen of the –OH functionalities on the glycerol rendering the solvent with increased H-bond donating acidity. It is observed that pyrene, a popular fluorescence probe of solvent polarity, does respond to the addition of LiCl to Glyceline, however, the change in pyrene response starts to become noticeable only at higher LiCl concentration (mLiCl ≥ 1.5 m). Reichardt’s betaine dye is found to be highly sensitive and versatile in gauzing physicochemical properties of DESs in the presence of LiCl.

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

The durability of ecological concrete in a marine environment was studied. Specimens of a six-year-old submerged ecological concrete from a breakwater located in the East Mediterranean sea were analyzed for their biological carbonate deposition cover, chloride effective diffusion, carbonation, and mineralogy. About 57% of the surface was found to be covered by biogenic-deposited carbonates. The effective chloride diffusion coefficient and the carbonation rate were found to be reduced proportionally to the biogenic-carbonate cover. Most of the aluminates were found in non-crystalline minerals. No evidence of a sulfate attack was found.

In this study, the effect of extraction conditions on the total phenolic content of clove buds was investigated. Clove buds were extracted using a deep eutectic solvents like mixtures choline chloride: lactic acid in the 1:2 molar ratio. Additionally, the HPLC-DAD method was used to determine the main components of the clove extracts, including eugenol, eugenol acetate, and β-caryophyllene. The conditions used in the extraction with choline chloride: lactic acid (molar ratio 1:2) included extraction temperature (t = 40 – 80°C), water addition (5.6 – 40%), and extraction time (30 – 90 min). Determination of the phenolic compounds was done by the Folin-Ciocalteu method. The optimum operating conditions for the total phenolic content were identified at 77°C, 30 min, and a water addition of 40%. Based on the results, the highest amount of eugenol (307.26 ± 8,44 mg/g dry raw material) was determined in clove extracts which were extracted under condition of 60°C, 22.8%, and 30 min.

The SLC12 family of cation-chloride-cotransporters (CCCs), comprising potassium chloride cotransporters (KCCs)-mediated Cl- extrusion relative to sodium chloride cotransporters (NKCCs)-mediated Cl- loading, play vital roles in cell volume regulation and ion homeostasis. These functions of the CCCs influence a variety of physiological processes, many of which overlap with the pathophysiology of cardiovascular disease. Although not all of the cotransporters have been linked to Mendelian genetic disorders, recent studies have provided new insights into their functional role in vascular and renal cells along with their contribution to cardiovascular diseases. Particularly, an imbalance in potassium levels promote the pathogenesis of atherosclerosis and disturbances in sodium homeostasis are one of the causes of hypertension. Recent findings even suggest hypothalamic signalling as a key signalling pathway in the pathophysiology of hypertension. In this review, we summarize and discuss the role of CCCs in cardiovascular disease with particular emphasis on knowledge gained in recent years on NKCCs and KCCs.

The seeds of red clover are heteromorphic and two color morphs can be visually recognized, light purple and yellow, resulting from heterozygosity and recessive homozygosity at two loci. Here, we report the responses of seed imbibition, seed germination, and early seedling growth of the two morphs to distilled water, sodium chloride, and complete nutrient solution. The sensitivity of red clover seeds to treatments increased with the stage of development in what seems to be a cumulative process. No differences were found in seed imbibition between morphs or between treatments. In seedling growth, on the contrary, treatments were always effective, but differences between morphs were only observed in seeds that were treated with nutrient solution, whereas in the intermediate stage of seed germination, the effects by treatments were observed together with the appearance of differences between morphs in distilled water and in the treatment by sodium chloride solution. Simultaneously, the superior performance of the yellow morph that was found in germination, which appears to be a trait stable across cultivars of red clover seeds, turned into a superior performance of the light purple morph in seedling growth.

Nasopharyngeal carcinoma (NPC) has not been thoroughly studied, and the pathogenesis of NPC is unclear. Scientists have neither discovered effective therapies nor achieved a desirable prognosis. Some studies have found that the regulation of intra- and extracellular ion channels hinges directly on cell apoptosis, and treatment with Gambogenic acid (GNA) brings changes to the volume-sensitive outwardly rectifying chloride (VSOR Cl-) current of CNE-2Z cells recorded by the patch clamp method. Nevertheless, rarely have any researchers probed into the relevance between this variation and the anti-tumor mechanism of GNA. This paper is suggested that GNA activates the VSOR Cl- current on the CNE-2Z cell membrane, and the activation of VSOR Cl- currents by GNA in CNE-2Z cells is blocked by the chloride channel blockers DIDS and DCPIB. GNA induces the down-regulation of GRP78 and up-regulation of ATF4 as well as chop proteins, which is evidence for the induction of CNE-2Z cell apoptosis, and this correlates with ER stress. GNA can activate the VSOR Cl- channel and lead to the occurrence of ER stress, thus inducing the apoptosis of CNE-2Z cells and inhibiting the proliferation of CNE-2Z cells.

Numerous studies have firmly established the role of ion channels in essentially all basic cellular functions. Apart from their role in ion transport, they can form macromolecular complexes with adhesion proteins, and signaling molecules. Ion channels are not only responsible for cellular electrogenesis and excitability, but they also regulate the necessary conditions for tissue homeostasis, such as differentiation, proliferation and apoptosis. Although cancer is not officially classified as a channelopathy, it has been increasingly recognized that ion channel aberrations play an important role in virtually all cancer types. Ion channels can exert pro-tumorigenic activities due to genetic or epigenetic alterations, or as a response to molecular signals, such as growth factors, hormones, etc. Prostate cancer is the second leading cause of cancer-related death in men in the United States. Increasing evidence suggests that ion channels and pumps play a critical role in the regulation of prostate cancer cell proliferation, apoptosis evasion, migration, epithelial-to-mesenchymal transition and angiogenesis. There is also evidence suggesting that ion channels might play a role in treatment failure in prostate cancer. Hence, they represent promising targets for diagnosis, staging and treatment. Here, the role of major types of ion channels involved in the development and progression of prostate cancer were reviewed. Identifying the underlying molecular mechanisms of the pro-tumorigenic effects of ion channels, may potentially inform the development of novel therapeutic strategies to counter this malignancy.

We utilize known exact analytic solutions of perfect fluid hydrodynamics to analytically calculate the polarization of baryons produced in heavy ion collisions. Assuming local thermodynamical equilibrium also for spin degrees of freedom, baryons get a net polarization at their formation (freeze-out). This polarization depends on the time evolution of the Quark-Gluon Plasma (QGP), which can be described as an almost perfect fluid. By using exact analytic solutions, we thus can analyze the necessity of rotation (and vorticity) for non-zero net polarization. In this paper we give the first analytical calculations for the polarization four-vector. We use two hydrodynamical solutions; one is the spherically symmetric Hubble flow (a somewhat oversimplified model, to demonstrate the methodology). The other solution which we use is a somewhat more involved one that corresponds to a rotating and accelerating expansion, and is thus well suited to investigate some main features of the time evolution of the QGP created in peripheral heavy-ion collisions (although there are still many numerous features of a real collision geometry that are beyond the reach of this simple model). Finally we illustrate and discuss our results on the polarization.

The safety concerns associated with current lithium-ion batteries are a significant drawback. A short-circuit within the battery's internal components, such as those caused by a car accident, can lead to ignition or even explosion. To address this issue, a polymer shear thickening electrolyte, free from flammable solvents, has been developed. It comprises a star-shaped oligomer derived from a trimethylolpropane (TMP) core and polyether chains, along with the inclusion of 20 wt.% nanosilica. Notably, the star-shaped oligomer serves a dual function as both the solvent for the lithium salt and the continuous phase of the shear thickening fluid. The obtained electrolytes exhibit an ionic conductivity of 10-6 S cm-1 at 20 °C and 10-4 S cm-1 at 80 °C, with a high Li+ transference number (t+ = 0.79). A nearly thirtyfold increase in viscosity to a value of 1187 Pa s at 25 °C and a critical shear rate of 2 s-1 were achieved. During impact, this electrolyte could enhance cell safety by preventing electrode short-circuiting.

A field study was conducted at the Eastern Mediterranean Agricultural Research Institute, Adana, Turkey, during the 2022/23 cropping seasons to examine the impact of Mepiquat chloride dosage applied at different intervals to optimize growth, yield characteristics enhancement and improve fiber quality attributes of cotton. The study employed a split-split plot design with three replications. The results revealed that differences among treatments were not statistically significant for most parameters investigated. The observed discrepancies indicated that all treatments tested in 2012 delayed cotton development, whereas in 2023, they led to premium fibers. In 2023, the fiber percentage was highest in the control treatment, and in 2022, it was highest at 400 mL·ha-1. Across all years, the Selin variety exhibited the highest fiber percentage when Mepiquat chloride was applied at the bolling stage. The shoot-root ratio was highest at 400 mL·ha-1 during harvest in 2022 and at 0 mL·ha-1 during the reproductive stage in 2023. Overall, the results demonstrated that the application of Mepiquat chloride altered the physiological characteristics of the cotton plants, leading to bottom-up effects on cotton performance. This implies that the effectiveness of Mepiquat chloride in cotton production to alleviate drought stress is influenced by weather-related conditions.

One of the influential factors in estimating the service life of reinforced concrete bridges (RCB) is determining the long-term seismic performance of these structures. Corrosion due to chloride ion diffusion leads to the destruction of critical members of the RCB during the useful life of the structure. So, the long-term seismic performance of the bridge deteriorates as a result. It is essential to study the effect of corrosion deterioration on the long-term seismic performance of bridges in the southern regions of Iran, near the coasts of the Persian Gulf and the Oman Sea, because of the seismicity of the region and high corrosion rate of reinforced concrete (RC) members is the result of environmental conditions. In order to investigate this issue, considering studies about environmental conditions of southern Iran, the onset time of corrosion in the columns, as seismic critical members of the bridge, was determined. Based on that, the corrosion's effect on characteristics of RC at specific time points during the bridge's useful life (0, 15, 30, 45, 60, 75 and 90 years) have been calculated. The effects of corrosion include deterioration of the core and cover concrete properties, steel bar and the connection between concrete and steel bar. In the next step, at each time point, according to the modified stress-strain relationships, the moment-curvature analysis of the bridge pier was done, and the properties of the plastic hinge were determined. Finally, based on the obtained data about plastic hinge characteristics at each time point, overload analysis of the bridge was performed in both longitudinal and transverse directions. Then the capacity curves of RCB were compared at the mentioned time-points. The results show that the capacity of the bridge deteriorates over time due to corrosion. Therefore, a proposal to increase the value of base shear design has been made to ensure the long-term seismic performance of RCB in corrosive environments.

Considering the important demand of fresh water and its scarce availability, water desalination is an interesting technology, producing about 44 Mm³/year worldwide, but, in general the most common desalination techniques are highly energy demanding. Freezing-Melting (F/M) desalination uses just up to 70% less thermal energy, but is the least used process mainly, due to the difficulty of the salt separation. This study proposes a model able to analyses the thermodynamic potential that allows the salt diffusion during the F/M process, using an aqueous solution of sodium chloride. This should allow to obtain a sensitive analysis of the process to promote the separation between the high concentration brine and the ice with liquid separation by physical process. The unidimensional model is based on the evolution of both processes: thermal and mass diffusions, depending on temperature and saline gradients, predicting whether the salt will remain inside the ice or not. Thus, the thermal potential is adjusted to frozen only when the salt has been "pushed" towards the brine. Mostly models have base their results on the assumption of a “certain value of saline concentration of the liquid fraction”, value in which there is great disagreement. In this paper the calculations are based on the concentration in the solid-liquid interface, which has been extensively studied and there is a coincidence in those results, being the main advantage of the proposed model.

The SOC (State of Charge) in Lithium-ion battery packs refers to determining a battery's current energy level or capacity at a given time. SOC is important for many battery-operated systems since it shows how much energy is available. In the earlier stage SOC is calculated by different techniques such as Coulomb counting, open-circuit voltage, Kalman filters, Data-Driven Approaches, and Real-Times Updates so these all methods are used to calculate the SOC Estimation in battery packs. In recent years, these old methods have had some errors and accuracy malfunctions in SOC estimation in battery packs. The SOC estimation errors occur on Two-Wheeler, Three-Wheeler, and four-wheeler of Electric Vehicles (EV). To Overcome this problem in current years the AI&ML Algorithms Methods are applied everywhere related to Accuracy, Solutions & All. To increase the accuracy of SOC Estimations we are going to use Machine Learning Algorithms to improve the SOC in Machine Learning there are various methods such as supervised, unsupervised, and reinforcement. Of these three methods, one of the best methods is to select the Algorithms is apply to the Battery packs to get accurate SOC Estimations. In Machine Learning, we select the Supervised Learning Algorithms. Currently, the project will focus on the use of a Supervised Machine Learning Algorithm which includes an Extra Trees Regressor, Bagging Regressor, K-Neighbors Regressor, Decision Tree Regressor, and Random Forest Regressor for SOC Estimation. In this, we will develop algorithms applied to Lithium-ion Battery Packs to accurately the SOC estimates. In conclusion, the algorithms we will develop by using Machine Learning are compared with the algorithms and analytical Models.

To address the limitations of the current anodes of Li+-ion batteries (LIBs), a Ge/GeO2/Carbon (Ge@GeO2-C) composite was designed by introducing a high-energy ball-milling process for advanced LIBs. Ge@GeO2-C is prepared and characterized by XPS, XRD, SEM, and TEM, which facilitate synthesis and provide controllability with respect to milling time. Interestingly, as the ball-milling time increased, the proportion of metallic Ge increased during the carbon thermal reduction reaction. The electrochemical characteristics of Ge@GeO2-C are assessed using differential capacity analysis (dQ/dV) and galvanostatic charge-discharge techniques to confirm its viability as an anode material in LIBs. The results demonstrated decent initial and secondary capacities of approximately 1800 mAh g-1 (for the first cycle) and 838 mAh g-1 (for the second cycle) at a rate of C/60 by the reaction between Ge and the Li-Ge complex. Furthermore, postmortem characterization was performed to gain an understanding of the material, suggesting future prospects for advanced LIBs.

With the rapid and continuous advancement and deployment of advanced energy storage de-vices, there has been significant interest in aqueous capacitors that possess non-flammable properties and high safety features. Consequently, extensive research efforts have focused on investigating zinc anodes and low-cost carbonaceous cathode materials. Despite these efforts, the development of high-performance zinc-ion capacitors (ZICs) still faces challenges such as limited cycling stability and low energy densities. In this study, we present a novel approach to address these challenges. We demonstrate the utilization of a three-dimensionally (3D) grown conductive porous carbon framework cathode coupled with zinc anode cells, which exhibit exceptional sta-bility and durability in ZICs. Our experiments reveal a remarkable cycling performance, with a capacity retention of approximately 97.3% and a coulombic efficiency of nearly 100% even after 10,000 charge-discharge cycles. These findings signify significant progress in enhancing the performance of ZICs.

Much attention has been attracted by aqueous zinc zinc-ion batteries (AZIBs) due to the features of inherent safety, environmental compatibility, low cost and fantastic energy density. Nevertheless, chemical corrosion and dendrite growth occurring on Zn anode during the charge/discharge process usually cause the surface passivation and short circuit of cells, seriously hindering the development of AZIBs. To settle these problems, a Cu(II)/polydopamine modified glass fiber (Cu-PDA/GF) is designed as separator. Due to the enhanced ionic conductivity of Cu(II) and PDA modified glass fiber separator, reversible zinc plating/striping is achieved in symmetric cells, which display long cycle life of over 1800 h at the current density of 1 mA cm−2 with the fixed capacity of 1 mAh cm−2. Moreover, the assembled Zn//V2O5 cells using Cu-PDA/GF separator also demonstrate improved capacity retention. The present study provides a simple separator modification strategy for high-performance and reliable AZIBs, which are conducive to energy storage devices.

In this paper, a new anode environmentally friendly for hydrogen production was developed based on 430 stainless steel with an electrodeposited cobalt layer. The novelty of this work is the cobalt source once the electrodeposition bath was obtained from recycling of spent Li-ion batteries cathode with composition LiCoO₂. The electrodeposited cobalt behaves as supercapacitor in KOH 1M. In the linear voltammetry in KOH 1M, when the overpotential reaches 370 mV, the anodic density current for 430 SS/Co is 19 mA cm⁻². Thus, the anode developed in this paper achieves the double of density current with half of production cost if compared with 316SS. Moreover the anode construction described in this paper is an excellent option for Li- ion battery recycling.

In this paper the application of recycled Li-ion batteries spent cathode (LIB-SC) combined with NaHCO₃/H₂O₂ system is presented for the first time in the literature as an alternative for degradation of potentially toxic organic molecules. The model pollutant choice was methylene blue molecule. The spent cathode composition corresponds to LiCoO₂, which was proved by the XRD and EDX. Regarding the decolorization of methylene blue solution, the addition of NaHCO₃ in comparison with only H₂O₂ reduces the complete decolorization time in 96%. This reduction occurs because the radical CO₃ is more stable than OH. In this way, the application the system proposed in this article is aimed at solving two major global problems: the disposal of cell phone batteries and the pollution of liquid effluents.

Crystalline β-cobalt hydroxide (β-Co(OH)₂) of different morphologies have been successfully synthesized with the addition of sodium hydroxide to cobalt nitrate solution and aging in the mother liquor. The rate of NaOH addition, ranging from 0.1 mL/min to 10 mL/min, influences the surface morphology with the obtained storage capability of the respective electrode. Characterization of the β-Co(OH)₂ was fully developed, including X-ray diffraction, scanning and transmission electron microscopy, and BET analyses. At a lower rate of NaOH addition, particles are like platelets, while for a higher rate (≥2 mL/min) grains are fused together forming a larger crystallite size. This result is supported by the X-ray diffraction structural analysis, where the phase evolution of (002) plane becomes distinct for the higher rate of NaOH addition. Lithium cobalt oxide (LiCoO₂) was synthesized through oxidation from the as-prepared β-Co(OH)₂ and LiOH. The electrochemical performance of as obtained LiCoO₂ is investigated using charge-discharge and cyclic voltammetric studies. The precursor β-Co(OH)₂ prepared at a lower rate of 0.1 mL/min in LiCoO₂ demonstrated the best electrochemical performance of 155 mAh/g. After 50 cycles, the capacity retention rate was 67% compared with the first cycle. Finally, we have attempted to correlate the amount of the available OH^- ions with the formation of platelets and the discharge capacity. This work has developed a methodology for the synthesis of LiCoO₂ using β-Co(OH)₂ in a facile chemical solution process.

In this report we have discussed the important role of molecular modeling, especially the use of the molecular dynamics method, in investigating transport processes in nanoporous materials such as membranes. With the availability of high performance computers, molecular modeling can now be used to study rather complex systems at a fraction of the cost or time requirements of experimental studies. Molecular modeling techniques have the advantage of being able to access spatial and temporal resolution which are difficult to reach in experimental studies. For example, sub-Angstrom level spatial resolution is very accessible as is sub-femtosecond temporal resolution. Due to these advantages, simulation can play two important roles: Firstly because of the increased spatial and temporal resolution, it can help understand phenomena not well understood. As an example, we discuss the study of reverse osmosis processes. Before simulations were used it was thought the separation of water from salt was purely a coulombic phenomenon. However, by applying molecular simulation techniques, it was clearly demonstrated that the solvation of ions made the separation in effect a steric separation and it was the flux which was strongly affected by the coulombic interactions between water and the membrane surface. Additionally, because of their relatively low cost and quick turnaround (by using multiple processor systems now increasingly available) simulations can be a useful screening tool to identify membranes for a potential application. To this end, we have described our studies in determining the most suitable zeolite membrane for redox flow battery applications. As computing facilities become more widely available and new computational methods are developed, we believe molecular modeling will become a key tool in the study of transport processes in nanoporous materials.

Abstract: Chitosan spherical scaffolds, derived from the deacetylation of chitin, are natural polymers with significant potential, though challenges remain in optimizing their properties. The use of chitosan as a carrier for the controlled release of iron chloride is not yet fully established, despite iron’s critical role in various essential biological processes, including as a component of metalloenzymes and in the maintenance of life. Methods: This study aimed to develop a novel protocol for synthesing chitosan scaffolds and to characterize their properties using analytical techniques. Additionally, the release profile of iron was modeled using two primary controlled-release mathematical models. Results: The results demonstrated successful synthesis and physicochemical characterization of the chitosan sphere scaffolds. These scaffolds exhibited appropriate topography for iron loading and cellular interaction, as confirmed by SEM analysis, and contained functional groups as identified by FTIR. The scaffolds were also semi-crystalline (XRD), showed controlled degradation, and were confirmed to be non-toxic biomaterials. Furthermore, the modeling of the controlled release of iron chloride adsorbed on the scaffold surface, as well as the modeling of iron chloride specimens using the MEDUZA software, was successfully conducted. A theoretical curve was generated from the experimental dose-response data collected over time, considering variations in pH and medium concentration. Conclusions: In conclusion, a novel protocol for chitosan-based carriers was successfully developed, enabling thorough physicochemical characterization and modeling of both absorption and controlled release.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

In this study, the extraction of rare earth elements (REEs) from chloride solutions containing mixtures of these metals with solutions of the mixtures of P507 and Cyanex 272 (1:1) of various concentrations was experimentally studied. It was shown that the distribution coefficients of all REEs decrease with increasing concentration of these metals in the initial solution, which is associated with the loading of the organic phase. The most significant improvement in the extraction is observed for heavy group of rare earth elements. The extractability of REEs enhances with increasing atomic number of the element, as is typical for the extraction of these metals with acidic organophosphorus extractants. The data obtained show that separation factors of adjacent rare earth elements mainly decrease with increasing concentration of metals in the initial aqueous solution. Increasing the concentration of the extractant mixture does not have a significant effect on the values of the adjacent REE separation factors. Analysis of the experimental results shows that two commercial products can be obtained from a concentrate of the medium-heavy group. In the first cascade, yttrium can be separated, in the second, a concentrate of dysprosium and terbium can be obtained.

Water quality monitoring was an important objective in the surroundings. In this study, we investigated the sensing characteristics of the arrayed flexible chloride sensor with XBee wireless sensing system. The sensitivity and linearity of the wireless chloride sensing devices were 91.6 mV/pCl and 0.988, respectively. The hysteresis voltages were 50.14 mV and 36.71 mV during the cycles of 1 M → 10⁻¹ M → 1 M → 10⁻³ M → 1 M and 1 M → 10⁻³ M → 1 M → 10⁻¹ M → 1 M, respectively. The selectivity coefficients of the ClO⁻ ion, ClO₄⁻ ion, NO₃⁻ ion and I⁻ ion for Cl⁻ ion were 5.0 × 10⁻², 1.0 × 10⁻¹, 5.9 × 10⁻³ and 5.6×10⁻¹, respectively. The sensing characteristics of real time measurement were investigated for dynamic microfluidic. The arrayed flexible chloride sensor was integrated with the microfluidic device, syringe pump and wireless sensing system. The sensitivity and linearity were 273.1 mV/pCl and 0.978 at 35 μL/min, respectively.

All-polyamide composite coated fabric (APCCF) materials were developed and used as the material of construction of textile bioreactors as a replacement of traditional costly steel-/concreate-based bioreactors. Then, APCCF-bioreactor was used to cultivate filamentous fungus Neurospora intermedia to produce ethanol and fungal biomass. The results showed similar performance of the fungus cultivated in stain-less steel bioreactors. Techno-economical analysis for a 5000-m³ APCCF bioreactor for fermentation facility would lead to a reduction of the annual production cost of the facility by $128,000,000 compared to similar stainless-steel processes. The comparative analyses (including mechanical and morphological analyses, density measurements and techno-economical analysis) revealed that the APCCF is a better candidate for material of construction of the textile bioreactor. The APCCF is a 100% recyclable single polymer composite which was prepared from textile production line waste.

Isotopes at the limits of nuclear existence are of great interest for their critical role in nuclear astrophysical reactions and their exotic structure. Experimentally, exotic nuclides are challenging to address due to low production cross-sections, overwhelming amounts of contamination, and lifetimes typically less than a second. To this end, a Multiple-Reflection Time-of-Flight mass spectrometer at the TITAN-TRIUMF facility was built to determine atomic masses. This device is a preferred tool to work with exotic nuclides due to its ability to resolve the species of interest from contamination and short measurement cycle times enabling mass measurements of isotopes with millisecond half-lives. With a relative precision of order $10^{-7}$, we demonstrate why the TITAN MR-TOF MS is the tool of choice for precision mass surveys for nuclear structure and astrophysics. The capabilities of the device are showcased in this work including new mass measurements of short-lived tin isotopes ($^{104-107}$Sn) approaching the proton dripline as well as $^{89}$Zr, $^{90}$Y, and $^{91}$Y. The last three illustrate how the broadband surveys of MR-TOF MS reach beyond the species of immediate interest.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

Colorectal cancer (CRC) remains a major global health issue. Although chemotherapy is the first-line treatment, its effectiveness is limited due to drug resistance developed in CRC. To overcome resistance and improve the prognosis of CRC patients, investigation for new therapeutic approaches is necessary. Using human colorectal adenocarcinoma (HT29) and metastatic CRC (SW620) cell lines, the potential anticancer properties of a newly synthesized compound 1-(Isobutyl)-3-(4-methylbenzyl) benzimidazolium chloride (IMBZC) were evaluated by performing MTT cytotoxicity, cell migration, and colony formation assays, as well as by monitoring apoptosis-related protein and gene expression using Western blot and reverse transcription-quantitative polymerase chain reaction technologies. Tested at various concentrations, the half-maximal inhibitory concentrations (IC50) of IMBZC on HT29 and SW620 cell growth were determined to be 6.97 μg/mL and 4.89 μg/mL, respectively. IMBZC did not alter cell growth of normal cells HEK293. In addition, IMBZC inhibited cell migration and significantly decreased colony formation, suggesting its promising role in suppressing cancer metastasis. Mechanistic analyzes revealed that IMBZC treatment increased the expression of pro-apoptotic proteins p53 and Bax, while decreasing the expression of anti-apoptotic proteins Bcl-2 and Bcl-xL, thus indicating the induction of apoptosis in IMBZC-treated CRC cells, compared to untreated cells. Additionally, the addition of IMBZC to conventional chemotherapeutic drugs (i.e., 5-fluorouracil, irinotecan, and oxaliplatin) resulted in an increase in the cytotoxic potential of the drugs. In conclusion, the study suggests that IMBZC has substantial anticancer effects against CRC cells through its ability to induce apoptosis, inhibit cancer cell migration and colony formation, and enhance the cytotoxic effects of conventional chemotherapeutic drugs. These findings indicate that IMBZC could be a promising chemotherapeutic drug for the treatment of CRC. Further research should be conducted using in vivo models to confirm the anti-CRC activities of IMBZC.

The thermal stabilizers, lubricant, and plasticizers are three crucial additives for processing poly (vinyl chloride) (PVC). In this study, a new mannitol stearate ester-based aluminum alkoxides (MSE-Al) was designed and synthesized as a novel additive for PVC. The thermal stability and processing performance of PVC stabilized by MSE-Al were evaluated by Congo red test, conductivity measurement, thermal aging test, ultravioletevisible (UV-vis) spectroscopy test, and torque rheometer test. Results showed that the addition of MSE-Al can not only markedly improve the long-term thermal stability of PVC, but also greatly accelerate the plasticizing and decrease the balance torque which demonstrated that MSE-Al possesses the lubricating property. Thus, MSE-Al was demonstrated to be able to provide tri-functional additive roles, e.g., thermal stabilizer, plasticizer, and lubricant. The test results for the thermal stability of PVC indicated that the initial whiteness of PVC stabilized with MSE-Al was not good enough, thus the synergistic effect of MSE-Al with zinc stearates (ZnSt₂) on the thermal stability of PVC was also investigated. The results showed that there exhibited an appreciable synergistic effect between MSE-Al and ZnSt₂. The thermal stabilization mechanism and synergism effect of MSE-Al with ZnSt₂ were then discussed.

Selenium is one of the inorganic compounds in human and animal nutrition and is involved in the proper functioning of the body. As a micronutrient, it actively contributes to the regulation of various metabolic activities, i.e., thyroid hormone, and protection against oxidative stress and cancer. Selenium anion also plays an essential role in the mechanism of immunity to viral infec-tions. However, this element can also be hazardous, especially in high concentrations. The toxicity of selenium is strongly associated with its chemical form. Se exhibits a narrow concentration window from having a positive to exerting a toxic effect. The daily uptake for humans is in the range of 55-400 µg/day. In higher doses (of the order of 900-1000 µg/day), it negatively affects the human body and causes DNA damage through the formation of free radicals. Increased reactivity of Se anion can also disrupt the integrity and function of DNA-repairing proteins. As the permis-sible concentration of Se in drinking water is 10 µg/L, it is vital to develop sensitive and robust methods of Se detection in aqueous samples.

This retrospective begins with Galvani's experiments on frogs at the end of the 18th century and his discovery of ‘animal electricity’. It goes on to illustrate the numerous contributions in the fields of physical chemistry in the second half of the 19th century (Nernst’s equilibrium potential, based on the work of Wilhelm Ostwald, Max Planck's ion electrodiffusion, Einstein's studies of Brownian motion), which led Bernstein to propose his membrane theory in the early 1900s as an explanation of Galvani’s findings and cell excitability. These processes were fully elucidated by Hodgkin and Huxley in 1952, by detailing the ionic basis of resting and action potentials, but without addressing the question of where these ions passed. The emerging question of the existence of ion channels, widely debated over the next two decades, was finally accepted and, a decade later, many of them began to be cloned. This led to the possibility of modelling the activity of individual neurons in the brain and then of simple circuits. Taking advantage of the remarkable advances in computer science in the new millennium, together with a much deeper understanding of brain architecture, more ambitious scientific goals were dreamed of to understand the brain and how it works. The retrospective concludes by reviewing the main efforts in this direction, namely the construction of a digital brain, an in silico copy of the brain that would run on supercomputers and behave just like a real brain.

In this research, 117,718 ionospheric perturbations, with a space size (t) of 20–300 s but no limit on amplitude (A) have been automatically searched globally by a software from ion density data measured by the DEMETER satellite for more than 6 years. The influence of the solar activity on the ionosphere has been firstly examined and the results have presented that the solar activities can globally enhance ionospheric irregularities but rarely induce plasma variations more than 100%. A statistical work has been performed on ion PERs to check their dependence on local time and it is shown that there are 24.8% perturbations appeared in daytime (10:30 LT) and 75.2% ones in nighttime (22:30 LT). Ionospheric fluctuations with an absolute amplitude A < 10% tend to be background variations and the percentages of positive perturbations with small A < 20% are 64% in daytime and 26.8% in nighttime, respectively, but this number is revers for mid-large amplitude PERs. There is a demarcation point in space size t = 120 s and occurrence probabilities of day PERs are always higher than that of nighttime ones before this point while this trend is contrary after this point. Distributions of PER according to various amplitudes or space scales have been characterized by typical seasonal variations either in daytime or in nighttime. The EIA only exists in dayside equinox and winter occupying two lowlatitude crests with lower Np. The huge WSA appears in all periods except for dayside summer full of PERs with enhanced amplitude, especially in winter night. The WN-like structure can be obviously figured out in all seasons showing absolutely space large-scales. In the meanwhile, several magnetic anomalous zones of planetary scale non-dipole fields, such as the SAMA, Northern Africa anomaly, and so on, have been also successfully detected by extreme negative ion perturbations in this time.

Adopting banana peel as raw material, the adsorption properties of banana peel hydrothermal carbon modified with KOH solution for lead ions in aqueous solution were studied. The surface structure and functional groups of the modified hydrothermal carbon were analyzed by XRD and SEM. The results showed that the banana peel hydrothermal carbon prepared from 0.5 mol/L KOH solution had large pores, and its adsorption capacity reached 42.92 mg/g at a pH value of 6; When the concentration of KOH solution is 0.5 mol/L, the solid liquid ratio is 2 g/L, the adsorption capacity reaches 21.39 mg/g, and the adsorption rate reaches 82.74%; When the concentration of lead solution increased to 100 mg/L, the adsorption capacity of modified hydrothermal carbon for lead ions decreased to 78.26%; The equilibrium adsorption time of lead ion in solution on phosphoric acid modified hydrothermal carbon from banana peel was 250 minutes, and the adsorption process met the quasi second order kinetic model and Freundlich isotherm equation, with an equilibrium adsorption rate of 88.62%. The adsorption of lead ions in solution by KOH modified hydrothermal carbon is mainly chemical physical adsorption.

Using banana peel as raw material, the adsorption properties of hydrothermal carbon pre-10 pared from banana peel modified with different concentrations of phosphoric acid solution for lead 11 ions in aqueous solution were studied. The surface structure and functional groups of the modified 12 hydrothermal carbon were analyzed by XRD and SEM. The results show that the surface of the 13 modified banana peel hydrothermal carbon prepared at 240℃ and 2mol/L phosphoric acid solution 14 has large pores. The adsorption capacity is larger when pH value is 6.When the concentration of 15 phosphoric acid solution was 2mol/L, the solid-liquid ratio was 2g/L, the adsorption capacity was 16 40.64mg/g, and the removal rate was 82.74%.When the initial concentration of lead solution in-17 creased to 100mg/L, the adsorption capacity of modified hydrothermal carbon for lead ion increased 18 to 76.81mg/g, and the removal rate decreased to 76.81%.The equilibrium adsorption time of banana 19 peel phosphoric acid modified hydrothermal carbon for lead ions in solution is 300min. The adsorp-20 tion process satisfies the pseudo-second-order kinetic model and Langmuir isotherm equation. The 21 reaction temperature is 313K, and the equilibrium adsorption capacity can reach 101.19mg/g. The 22 adsorption of Pb ions in aqueous solution by phosphoric acid modified hydrothermal carbon is 23 dominated by single layer chemisorption. The artificial neural network has a fitting correlation of 24 0.99, and the adsorption process includes physical adsorption, electrostatic attraction, ion exchange, 25 and surface complexation.

The economics and safety of reactors can be affected by the diffusion of fission products into graphite. Xenon (Xe) fission products diffusing into the graphite is the most critical neutron absorber and poison that can slow down or stop the chain reaction. The transport parameters for inhibiting the xenon diffusion in graphite are therefore the utmost scientific problem. Self-sintered nanopore-isotropic (~ 40nm) graphite (SSNG) derived from green pitch coke can decrease Xe diffusion into the graphite. In this study, a method for measurement of diffusion coefficients of fission products diffusion in graphite by Rutherford backscattering spectrometry (RBS) was reported. The SSNG substrates were implanted with Xe at a dose of 4.8×1015 ions/cm2 and energy of 7 MeV. The RT-implanted samples were annealed in a vacuum at 650°C for 9 h. The implanted and annealed samples were characterized by RBS. The diffusion coefficient D(Xe,650°C) is 6.49×10-20 m2/s. The results indicate the excellent ability to inhibit Xe diffusion of the SSNG and present significance in designing and evaluating the safety of nuclear reactors.

Anode materials based on TiO2 nanoparticles of different morphologies were prepared using the hydrothermal method and characterized by various techniques, such as X-ray diffraction (DRX), scanning electron microscopy (FE-SEM), and N2 absorption. The TiO2 nanoparticles prepared were used as anode materials for lithium-ion batteries (LIBs), and their electrochemical properties were tested using discharging/charging measurements. The results showed that the initial morphology of the nanoparticles plays a minor role in battery performance after the first few cycles and that better capacity was achieved for TiO2 nanobelt morphology. The sharp drop in the specific capacity of LIB during their first cycles is examined considering changes in the morphology of TiO2 particles and their porosity properties in terms of shape and connectivity.

Breast cancer is a complex and heterogeneous disease that displays diverse molecular subtypes and clinical outcomes. Although it is known that the location of tumors can affect their biological behavior, the underlying mechanisms are not fully understood. In our previous study, we found a differential methylation profile and membrane potential between left (L) and right (R)-sided breast tumors. In this current study, we aimed to identify the ion channels responsible for this phenomenon and determine any associated phenotypic features. To achieve this, experiments were conducted in mammary tumors in mice, human patient samples, and with data from public datasets. The results revealed that L-sided tumors have a more depolarized state than R-ones. We identified a 6-ion channel-gene signature (CACNA1C, CACNA2D2, CACNB2, KCNJ11, SCN3A, and SCN3B) associated with side: L-tumors exhibit lower expression levels than R-ones. Additionally, in silico analyses show that the signature correlates inversely with DNA methylation writers and with key biological processes involved in cancer progression, such as proliferation and stemness. The signature also correlates inversely with patients’ survival rates. In an in vivo mouse model, we confirmed that KI67 and CD44 markers were increased in L-sided tumors and similar tendency for KI67 was found in patient L-tumors. Overall, this study provides new insights into the potential impact of anatomical location on breast cancer biology and highlights the need for further investigation into possible differential treatment options.

We present a compact polarimeter for 3He ions with special emphasis on the analysis of short-pulsed beams accelerated during laser-plasma interactions. We discuss the specific boundary conditions for the polarimeter, such as the properties of laser-driven ion beams, the selection of the polarization-sensitive reaction in the polarimeter, the representation of the analyzing-power contour map, the choice of the detector material used for particle identification, as well as the production procedure of the required deuterated foil-targets. The assembled polarimeter has been tested using a tandem accelerator delivering unpolarized 3He ion beams, demonstrating good performance in the few-MeV range. The statistical accuracy and the deduced figure-of-merit of the polarimetry are discussed, including the count-rate requirement and the lower limit of accuracy for beam-polarization measurements at a laser-based ion source.

We study the application of Optimal Control Theory to Ion Cyclotron Resonance. We test the validity and the efficiency of this approach for the robust excitation of an ensemble of ions with a wide range of cyclotron frequencies. Optimal analytical solutions are derived in the case without any pulse constraint. A gradient-based numerical optimization algorithm is proposed to take into account limitation in the control intensity. The efficiency of optimal pulses is investigated as a function of control time, maximum amplitude and range of excited frequencies. A comparison with adiabatic and SWIFT pulses is done. On the basis of recent results in Nuclear Magnetic Resonance, this study highlights the potential usefulness of optimal control in Ion Cyclotron Resonance.

The separator membrane is an essential component of lithium-ion batteries, separating the anode and cathode and controlling the number and mobility of the lithium ions. Among the polymer matrices most investigated for battery separators are poly(vinylidene fluoride) (PVDF) and its copolymers poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE), poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), and poly(vinylidene fluoride-cochlorotrifluoroethylene) (PVDF-CTFE), due to their excellent properties such as high polarity and the possibility of controlling the porosity of the materials through binary and ternary polymer/solvent systems, among others. This review presents the recent advances on battery separators based on poly(vinylidene fluoride) (PVDF) and its copolymers for lithium-ion batteries. It is divided in the following sections: single polymer and co-polymers, surface modification, composites and polymer blends. Further, a critical comparison between those membranes and other separator membranes is presented, as well as the future trends on this area.

We describe our investigations of the surface physicochemical and biological properties of polylactic acid modified by silver, argon and carbon ion implantation to doses of 1 × 10¹⁴, 1 × 10¹⁵ and 1 × 10¹⁶ ion/cm² at energies of 20 keV (for C and Ar) and 40 keV (for Ag). X-ray analysis shows enhancement of coherent scattering regions and lattice constant increase after ion implantation. Secondary electron mass-spectrometry indicates that Ag concentration in the subsurface layer is less than 80%, but at a depth of 500 nm does not exceed 1–2%. The silver forms metal particles in the subsurface layer rather than making additional chemical bonds with polymer atoms. Atomic force microscopy reveals that the higher the irradiation dose the larger the surface roughness of the samples. Ag-irradiated samples implanted to a dose of 1 × 10¹⁶ ions/cm² have the highest roughness, 190 nm. Our investigation of the cytotoxicity of two individual donor macrophages shows that Ag-implanted polylactic acid has no negative impact on immune system cells and could be a promising material for biomedical application.

The cell case temperature versus time profiles of a multistage fast charging technique (4C-1C-CV)/fast discharge (4C) in a 2.3 Ah cylindrical lithium-ion cell are analyzed using a 1D thermal model. Heat generation is dominated by the irreversible component associated to cell overpotential, although evidences of the reversible component are also observed, associated to the heat related to entropy from the electrode reactions. The final charging stages (i.e., 1C-CV) significantly reduce heat generation and cell temperature during charge, resulting in a thermally safe charging protocol. Cell heat capacity was determined from cell specific heats and cell materials thickness. The 1D model adjustment of the experimental data during the 2 min. resting period between discharge and charge allowed us to calculate both the time constant of the relaxation process and the cell thermal resistance. The obtained values of these thermal parameters used in the proposed model are almost equal to those found in the literature for the same cell model, which suggests that the proposed model is suitable for its implementation in thermal management systems.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

This study investigates the stress corrosion cracking (SCC) behavior of type 316L stainless steel (SS316L) produced with sinter-based material extrusion additive manufacturing (AM). This technology has been shown to produce SS316L with microstructures and mechanical properties comparable to its wrought counterpart in the annealed condition. However, despite plenty of research on SCC of SS316L, little is known about SCC in sinter-based AM SS316L. This study focuses on the influence of sintered microstructures on susceptibility to SCC initiation and crack-branching. Custom-made C-rings were exposed to different stress levels in acidic chloride solutions at various temperatures. To better understand the SCC behavior of SS316L, solution-annealed (SA) and cold-drawn (CD) wrought SS316L were tested for comparison. Results showed that sinter-based AM SS316L was more susceptible to SCC initiation than SA wrought SS316L but more resistant than CD wrought SS316L. Moreover, sinter-based AM SS316L showed noticeably better resistance to crack-branching than both wrought SS316L counterparts. The investigation was supported by comprehensive pre- and post-test microanalysis using light optical microscopy (LOM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and micro-computed tomography (micro-CT)

Positively charged polyelectrolytes hold significant potential as materials for creating antibacterial coatings. Water-soluble macromolecules can be easily deposited onto a treated surface through various techniques, forming a film that provides antimicrobial properties to the surface through electrostatic interactions with bacterial membranes. The structural and molecular weight characteristics of the polymers play a crucial role in the physical and mechanical properties of the coatings. In this study, we investigated the properties of branched polyethyleneimine (PEI) and linear polydiallyldimethylammonium chloride (PDADMAC) coatings with different molecular weights of polymer samples to determine their suitability as stable coatings with antibacterial properties against foodborne bacteria. Using thermogravimetric analysis, dynamometry, and dynamic light scattering, we examined the physicochemical and mechanical properties of the macromolecules in water solutions and in coatings. Microbiological study was conducted to analyze the biocidal activity of the polycations in solutions and on the surface of coatings. Our findings showed that the moisture saturation of the polycationic coatings did not significantly depend on the chemical nature of charged groups or the molecular weight or architecture of macromolecules. Moreover, biocidal activity was not found to depend on the molecular weights of PEI and PDADMAC. However, the lowering of the molecular weight of polymers resulted in the loss of cohesive forces in the coatings and to dramatically loss of the stability towards wash-off with water. The diffusion coefficient (D0) of macromolecules was identified as a key parameter for the wash-off mechanism. Films formed by molecules with D0 below 1×10-7 cm2/s demonstrated high resistance to wash-off procedures. We demonstrated that PEI and PDADMAC samples with high molecular weights showed high antimicrobial activity towards L. monocytogenes. Our results highlight the importance of macromolecule characteristics in the development of new biocidal coatings based on polycations.

Oxidative stress, characterized by an imbalance between the production of reactive oxygen species (ROS) and the body's antioxidant defenses, significantly affects cellular function and viability. It plays a pivotal role in modulating action potentials (APs), essential for properly functioning excitable cells such as neurons, smooth muscles, pancreatic beta cells, and myocytes. The interaction between oxidative stress and AP dynamics is crucial for understanding the pathophysiology of various conditions, including neurodegenerative diseases, cardiac arrhythmias, and ischemia-reperfusion injuries. This review explores how oxidative stress influences APs, focusing on alterations in ion channel functionality, signaling pathways, and membrane properties. By integrating current research, we aim to elucidate how oxidative stress contributes to disease progression and discuss potential therapeutic interventions targeting this interaction.