1 / 97

CONCRETE AGGREGATES

CONCRETE AGGREGATES. binding medium (mortar) Portland Cement Concrete relatively inert filler materials (aggregates)

abra-pacheco
Download Presentation

CONCRETE AGGREGATES

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. CONCRETE AGGREGATES

  2. binding medium (mortar) • Portland Cement Concrete relatively inert filler materials (aggregates) • In concrete mixtures the proportions of cement paste & aggregates is controlled by the following factors: • Suitable workability & placeability of fresh mass. • Adequate strength & durability of hardened product. • Minimum cost of the final product

  3. The aggregate occupies ~70-75% of the volume of concrete, so its quality is of great importance. • Aggregates may affect the following properties of concrete: • Strength • Durability • Structural Performance • Economy

  4. Aggregates have 3 main functions in concrete: • To provide a mass of particles which are suitable to resist the action of applied loads & show better durability then cement paste alone. • To provide a relatively cheap filler for the cementing material. • To reduce volume changes resulting from setting & hardening process & from moisture changes during drying.

  5. The properties of concrete are affected by the properties of aggregate: • The mineral character of aggregate affects the strength, durability, elasticity of concrete. • The surface characteristics of aggregate affects the workability of fresh mass & the bond between the aggregate & cement paste in hardened concrete. If it is rough, workability decreases & bond increases. • The grading of aggregate affects the workability, density & economy. • The amount of aggregate in unit volume of concrete

  6. Higher aggregate amount/unit volume of concrete • Results in less volume changes during setting & hardening or moisture changes. (increase in volume stability) • Increase in strength & durability • Decrease in cost • It is a common practice to use as much aggregate as possible in concrete

  7. However, all aggregates are not inert: • The physical action: swelling & shrinkage • The chemical action: alkali-agg. Reaction • The thermal action: expansion & contraction • Like the other ingredients of concrete, aggregates must also be chosen with certain care to end up with a satisfactory concrete.

  8. CLASSIFICATION OF AGGREGATES • According to Source: • Natural aggregate: Native deposits with no change in their natural state other than washing, crushing & grading. (sand, gravel, crush stone) • Artificial aggregates: They are obtained either as a by-product or by a special manufacturing process such as heating. (blast furnace slag, expanded perlite)

  9. According to Petrological Characteristics: • Igneous rocks: are formed by solidification of molten lava. (granite) • Sedimentary rocks: are obtained by deposition of weathered & transported pre-existing rocks or solutions. (limestone) • Metamorphic rocks: are formed under high heat & pressure alteration of either igneous & sedimentary rocks (marble).

  10. According to Unit Weight: • Heavy weight agg.: Hematite, Magnetite Specific Gravity, Gs> 2.8 • Normal weight agg.:Gravel, sand, crushed stone 2.8 < Gs< 2.4 • Light weight agg.:Expanded perlite, burned clay Gs< 2.4

  11. Normal-Weight Aggregate ASTM C 33 Most common aggregates • Sand • Gravel • Crushed stone Produce normal-weight concrete 2200 to 2400 kg/m3

  12. Lightweight Aggregate (1) ASTM C 330 Expanded • Shale • Clay • Slate • Slag Produce structural lightweight concrete 1350 to 1850 kg/m3

  13. Lightweight Aggregate (2) ASTM C 330 • Pumice • Scoria • Perlite • Vermiculite • Diatomite Produce lightweight insulating concrete— 250 to 1450 kg/m3

  14. Heavyweight Aggregate ASTM C 637, C 638 (Radiation Shielding) • Barite • Limonite • Magnetite • Ilmenite • Hematite • Iron • Steel punchings or shot Produce high-density concrete up to 6400 kg/m3

  15. According to Size: • Fine aggregate: d ≤ 5 mm • Coarse aggregate: d > 5 mm • Aggregatescontaining a whole range of particles are named as “all-in” or “pit-run” aggregates.

  16. Fine Aggregate • Sand and/or crushed stone • < 5 mm • F.A. content usually 35% to 45% by mass or volume of total aggregate

  17. Coarse Aggregate • Gravel and crushed stone •  5 mm • typically between 9.5 and 37.5 mm

  18. Aggregate Characteristics and Tests

  19. Aggregate Characteristics and Tests

  20. SAMPLING • Tests in the lab is carried out on the samples. So, certain precautions in obtaining a sample must be taken to obtain “representative sample”. • The main sample is made up of portions drawn from different points. The minimum number of portions, increment, is 10 & they should add up to a weight not less than:

  21. * Details are provided in ASTM D 75 & TS 707

  22. Methods of reducing the amount of sample: • Quartering: • Mix the field sample over three times on a level surface. • Shovel the sample to a conical shape. • Press the apex & flatten the conical shape. • Divide them into four equal quarters. • Discard two diagonally opposite quarters & use the remainder. • If this remainder is still too large follow the same path. 2 Side Side Top Top

  23. Splitting: • Use the “sample splitter” to divide the aggregate sample into two. • Sample splitter is a box with an even # of chutes alternately discharging to two sides. • The width of each chute should be greater than 1.5 times the size of the largest aggregate size. • If the remainder is still too large follow the same path.

  24. PARTICLE SHAPE & SURFACE TEXTURE • In addition to petrological character, the external characteristics, i.e. The shape & surface texture of aggregates are of importance. Particle Shape • Rounded: Completely water worn & fully shaped by attrition. (River Gravel) • Irregular: Partly shaped by attrition so it contains some rounded edges. (Land Gravel)

  25. L w t • Angular: Has sharp corners, show little evidence of wear. (Crushed Stone) • Flaky: Thickness is relatively small with respect to two other dimensions. (Laminated Rocks) • Elongated: Have lengths considerably larger than two other dimensions

  26. FLAT ELONGATED ANGULAR ROUND

  27. Rounded aggregates are suitable to use in concrete because flaky & elongated particles reduce workability, increase water demand & reduce strength. • In the case of angular particles, the bond between agg. Particles is higher due to interlocking but due to higher surface area, angular particles increase water demand & therefore reduce workability. As a result, for the same cement content & same workability rounded agg. Give higher strength. ?

  28. Surface Texture • This affects the bond to the cement paste & also influences the water demand of the mix. Smooth: Bond b/w cement paste & agg is weak. Rough: Bond b/w cement paste & agg. is strong. • Surface texture is not a very important property from compressive strength point of view but agg. Having rough surface texture perform better under flexural & tensile stresses.

  29. SMOOTH ROUGH

  30. Grading of Aggregates ―Grading is the particle-size distribution of an aggregate as determined by a sieve analysis using wire mesh sieves with square openings. ASTM C 33 Fine aggregate―7 standard sieves with openings from 150 μm to 9.5 mm Coarse aggregate―13 sieves with openings from 1.18 mm to 100 mm

  31. Agg. #4 ***** #8 #16 #30 #50 #100 Pan Sieve shaker Lateral & Vertical motion • The material is sieved through a series of sieves that are placed one above the other in order of size with the largest sieve at the top. • Dry agg. is sieved to prevent lumps.

  32. The particle size distribution in an aggregate sample is known as “gradation”. • Strength development of concrete depends on degree of compaction & workability together with many other factors. So, a satisfactory concrete should be compacted to max density with a reasonable work. • On the other hand, in good concrete all aggregate particles must be covered by cement paste.

  33. The grading of aggregate must be so that the workability, density & volume stability of concrete may not be adversely affected by it. • Fine Particles → higher cost • Coarse Particles → less workability • A reasonable combination of fine & coarse aggregate must be used. This can be expressed by maximum density or minimum voids concept.

  34. A cube with a dimension of 2Dx2Dx2D is filled with spheres of diameter D Vcube=(2D)3=8D3 1Vsphere=(4/3)π(D/2)3≈0.52D3 8*Vsp=8*0.52D3≈4.2D3 (solid volume) Void Volume=8D3-4.2D3=3.8D3 D 2D

  35. Same cube filled with spheres of diameter D/4. Solid Volume=8*8*8*(4/3)π(D/8)3≈4.2D3 #of spheres Void Volume≈3.8D3 • Size of agg. is not important. If an agg. with the same size is used amount of void volume will not change. So, to overcome this different sizes of particles should be used. • However, you should not forget that as agg. get finer, the surface area increases. • More surface area → more paste & water requirement

  36. Reduction of Voids

  37. Factors Affecting a Desired Grading • Surface area of the Aggregate The lower the surface area, the lesser is the paste requirement. • Relative Volume of Agg. in Concrete Higher volume of agg.: →economical →higher strength, higher volume stability →less workability !

  38. Workability: The ease with which a concrete mixture can be mixed, transported, placed in theform & compacted without any segregation. Workability increases as the amount of paste b/w fine agg. part increases. It also increases as the amount of mortar b/w coarse agg. particles increases. • Segregation: Seperation of the particles with different sizes & specific gravities. The requirements of workability and absence of segregation tend to oppose each other. Thus, these two factors are interrelated. The major of these is workability which, in turn, affects most of the properties of concrete.

  39. Determination of the Grading of Aggregate • There are two different methods for determining the agg. grading: • Fineness Modulus (FM) • Granulometry • The grading of the particles in an agg. sample is performed by “sieve analysis”. The sieve analysis is conducted by the use of “standard test sieves”. Test sieves have square openings & their designation correspond to the sizes of those openings.

  40. Fineness Modulus (FM): FM is a single figure which is the sum of cumulative % retained on a series of sieves having a clear opening half that of the preceeding one. Usually determined for fine agg. For Fine Agg.→#4, #8, #16, #30, #50, #100 {practical limits→2-3.5} For Coarse Agg.→Fine set+3/8”+3/4”+1 ½”+3” {practical limits→5.5-8.0} The FM of the mixture of two or more agg. is the weighted average of the FM of that two more agg. Σ (% cumulative retained on each sieve) FM = 100

  41. Ex:A 500gr sample of a Fine Agg. was sieved. Determine FM? Pan is not included. Only standard sieves are included, if we were given #10 sieve you should not use that in calculations 6+22+42+66+91+98 FM = = 3.25 100

  42. Fine Set+3/8”+3/4”+1 ½”+3” FM = 100 30+65+90+100+100+100+100+100+100 FM = = 7.85 100 Ex: Determine the FM for the 1000gr sample of Coarse Agg.

  43. 3.25X+7.85(100-X) X = 23 = 6.8 100 Ex: The fine agg. with the FM=3.25 and the coarse agg. with the FM=7.85 are available. Combine them in such a way that the FM becomes 6.8 X : Volume of Fine agg. *23% of fine agg. and 77% of coarse agg. should be mixed.

  44. Granulometry: • The FM is not always representative of the gradation of an aggregate sample and various gradation curves may give the same FM. • In the gradation curves, the vertical axis represents the % passing & the horizontal axis represents the sieve opening. • A logarithmic scale is used for horizontal axis.

  45. A good aggregate gradation for a particular concrete is the one that leads to a workable, dense & uniform concrete, without any segregation of particles.

  46. There is no single “ideal” grading curve. Instead, standards provide upper & lower limits.

  47. * Changes with max aggregate size

More Related