Load Calculation

An estimate of heat and contaminant emission to the room air is needed early in the design process. Table 8.4 presents typical parameters of interest. [Pg.608]

At a later stage in design the position and characteristics of releases are needed such as [Pg.608]

described as power, as temperature on the described surface, or as advection of heat along with substance flowing out of the production process. [Pg.608]

Momentum and density of flow released from openings and from processes. [Pg.608]

Moisture, as emission of water and vapor from the process. [Pg.608]

In case use of local protection system effect on exposure of the process, load calculations shall he revised. products... [Pg.18]

Collect properties of building layout, structures, and openings and their properties as basic values for load calculations. [Pg.21]

This task considers the effect of building and construction properties to indoor environment. It requires the collection of properties of building layout, construction, openings and their properties as basic values for load calculations. See Fig. 3.5. [Pg.24]

This task identifies characteristics of each source and calculation methods for load calculation. See Fig. 3.7. [Pg.27]

Heating and cooling load calculation for HVAC system design is based on the heat balance principle. For the given building, room, or independent building zone, heat balance components should be established and analyzed. The ma or heat sources and sinks in industrial buildings are ... [Pg.423]

ASHRAE. fundamentals handbook, 1997. Non-residential cooling and heating load calculations. ch. 28. Atlanta, GA American Society of Heating, Refrigeration and Air-Condi-tiomng Engineers. [Pg.1081]

Use a 750 MBtu/hr reboiler to allow for startup heat loads. Calculate Duties of Heat Exchangers... [Pg.224]

Some typical specific heats are listed in the tables, and a few examples of heat load calculations may be useful. [Pg.315]

Figure 26.3 Air-conditioning load calculation sheet (part) (Courtesy of the Electricity Council)...

The cummulative values of the initiator loading calculated with equations 20a and 28 should agree, betwen themselves and with the measured values. As it is shown in Figure 5 this is not the case, a correction for the Initiator balances seems to be required. Larger efficiency values can be obtained if it Is assumed that all the initiator radicals have the same efficiency. Under this condition, the radical concentration is given by... [Pg.211]

The effect has been observed for a variety of combustible materials, but no variations in charge to combustible mass, charge type, structure volume, or degree of venting have been tested. The implications of the data accumulated so far are that quasi-static loading calculations should include estimates of contributions from the burning of combustible materials whenever such materials are expected to be in intimate contact with HI sources. [Pg.18]

The loads from external near-surface burst explosions are based on hemispherical surface burst relationships. Peak pressure (P psi) and scaled. impulse Ci/W psi/lb ) are plotted vs. scaled distance (R/W ft/lb ). Roof and sidewall elements, side-on to the shock wave, see side-on loads (P and i ). The front wall, perpendicular to the shock wave, sees the much higher reflected shock wave loads (P and i ). An approximate triangular pressure-time relationship is shown in Figure 5a. The duration, T, is determined from the peak pressure and impulse by assuming a triangular load. Complete load calculations include dynamic loads on side-on elements, the effect of clearing times on reflected pressure durations, and load variations on structural elements due to their size and varying distance from the explosive source. [Pg.101]

The critical load concept is intended to achieve the maximum economic benefit from the reduction of pollutant emissions since it takes into account the estimates of differing sensitivity of various ecosystems to acid deposition. Thus, this concept is considered to be an alternative to the more expensive BAT (Best Available Technologies) concept (Posch et al., 1996). Critical load calculations and mapping allow the creation of ecological-economic optimization models with a corresponding assessment of minimum financial investments for achieving maximum environmental protection. [Pg.8]

The key shortcoming of the CLL approach from an EIA practitioner s perspective is data uncertainty—a sore subject for any predictive exercise. This is especially true for a simplified algorithm for critical load calculation (see above). Both assessors and reviewers will ask the following questions ... [Pg.17]

It should be stressed that PROFILE needs the nutrient uptake limited to PROFlLE-acceptable layer (0.5-1 m depth) for simplicity, whereas the real nutrient uptake takes place down to the 3-5-7-10 m depth corresponding to the distribution of tree roots. So, the nutrient uptake in a PROFlLE-acceptable layer is always less than the whole nutrient uptake. This might be a source of uncertainty in critical load calculations. [Pg.52]

General Approaches for Calculating Critical Loads of Heavy Metals Discussing the problems related to the critical load calculation, an attention should be paid to (i) selection of a receptor of concern, (ii) critical limits, (iii) possible calculation methods, (iv) the necessary input data and (v) the various sources of error and uncertainty (de Vries andBakker, 1998a, 1998b). [Pg.59]

The assessment of a critical limit for the receptor of concern is a second step in the flowchart for calculating critical loads of heavy metals (see Figure 4). Since critical loads of heavy metals are related to the concentration of a single metal in any link of a biogeochemical food web, the correct selection of critical limits is a step of major importance in deriving the critical loads. Those critical limits, which depend on the kind of effects considered and the amount of harm accepted, constitute the basis of the critical load calculation and determine their magnitudes. [Pg.62]

In order to gain insight into the consequences of the choice of a certain model and limits, one could perform critical load calculations with different models (complex dynamic models versus simple steady-state models) using various limits and compare the results. In this way, one also gets insight into (i) the differences in vulnerability of the various environmental compartments and related organisms and (ii) the relevance of the different processes in the systems and of the different ways of parameterizing certain processes. [Pg.69]

ENVIRONMENTAL RISK ASSESSMENT UNDER CRITICAL LOAD CALCULATIONS... [Pg.75]

ERA in general is a process, as is EIA (Environmental Impact Assessment), and not the occasional report or document that is published at various steps. The framework for the orderly process, which has been developed for various environmentally sound projects can be applied also for acidification oriented projects and especially for an evaluation of ecosystem sensitivity to acid deposition and critical load calculations. Central management of the process is an essential feature. [Pg.75]

The ecosystem acidification and critical load calculation processes are only partly scientific exercises, being connected closely with economic development of all countries. So, in different projects the hazards of concern include ecosystem damage due to acidification and eutrophication processes (e.g., decreased productivity and biodiversity, soil erosion, drinking water quality, reproduction losses, etc.), firstly, in local scale and, secondly, in regional scale that may lead to transboundary pollution. For more details see Figure 2. [Pg.78]

Under critical loads calculations the uncertainties arise from ... [Pg.78]

Methods of Critical Load Calculations for Heavy Metals... [Pg.80]

In this case study, steady-state mass balance models are applied for critical loads calculation for the heavy metals. [Pg.81]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...