Process chromatography, analytical method

Mixtures can be identified with the help of computer software that subtracts the spectra of pure compounds from that of the sample. For complex mixtures, fractionation may be needed as part of the analysis. Commercial instmments are available that combine ftir, as a detector, with a separation technique such as gas chromatography (gc), high performance Hquid chromatography (hplc), or supercritical fluid chromatography (96,97). Instmments such as gc/ftir are often termed hyphenated instmments (98). Pyrolyzer (99) and thermogravimetric analysis (tga) instmmentation can also be combined with ftir for monitoring pyrolysis and oxidation processes (100) (see Analytical methods, hyphenated instruments). [Pg.315]

At present moment, no generally feasible method exists for the large-scale production of optically pure products. Although for the separation of virtually every racemic mixture an analytical method is available (gas chromatography, liquid chromatography or capillary electrophoresis), this is not the case for the separation of racemic mixtures on an industrial scale. The most widely applied method for the separation of racemic mixtures is diastereomeric salt crystallization [1]. However, this usually requires many steps, making the process complicated and inducing considerable losses of valuable product. In order to avoid the problems associated with diastereomeric salt crystallization, membrane-based processes may be considered as a viable alternative. [Pg.126]

One of the attractive features of SFE with CO2 as the extracting fluid is the ability to directly couple the extraction method with subsequent analytical methods (both chromatographic and spectroscopic). Various modes of on-line analyses have been reported, and include continuous monitoring of the total SFE effluent by MS [6,7], SFE-GC [8-11], SFE-HPLC [12,13], SFE-SFC [14,15] and SFE-TLC [16]. However, interfacing of SFE with other techniques is not without problems. The required purity of the CO2 for extraction depends entirely on the analytical technique used. In the off-line mode SFE takes place as a separate and isolated process to chromatography extracted solutes are trapped or collected, often in a suitable solvent for later injection on to chromatographic instrumentation. Off-line SFE is inherently simpler to perform, since only the extraction parameters need to be understood, and several analyses can be performed on a single extract. Off-line SFE still dominates over on-line determinations of additives-an... [Pg.429]

The strategy depends on the situation and how we measure the concentration. If we can rely on pH or absorbance (UV, visible, or Infrared spectrometer), the sensor response time can be reasonably fast, and we can make our decision based on the actual process dynamics. Most likely we would be thinking along the lines of PI or PID controllers. If we can only use gas chromatography (GC) or other slow analytical methods to measure concentration, we must consider discrete data sampling control. Indeed, prevalent time delay makes chemical process control unique and, in a sense, more difficult than many mechanical or electrical systems. [Pg.102]

In order to understand the removal of FMs during wastewater treatment, it is necessary to measure these compounds throughout the wastewater treatment process. Because of the complex nature of wastewater matrices and the low concentration of FMs (0.001-60 pg/L) [11] throughout the treatment plant, accurate and sensitive analytical methods have been developed by a number of researchers. Fortunately, the analytical techniques developed to measure traditional SOCs, such as solvent extraction, extract concentration, and analysis by gas chromatography-mass spectrometry, in general also apply to FMs. [Pg.84]

Chromatography is the primary analytical method in chemical analysis of organic molecules. This technique is used to analyze reaction products in most of the processes we have been describing. The analysis of reaction products and of the efficiency of separation units usually is done by analytical chemists (who earn lower salaries), but chemical engineers need to be aware of the methods of analysis used and their reliability. [Pg.509]

Internal reflection spectroscopy is widely applied for on-line process control. In this type of application, the chemical reactor is equipped with an internal reflection probe or an IRE. The goal of this type of application is the quantification of reactant and/or product concentrations to provide real-time information about the conversion within the reactor. In comparison with other analytical methods such as gas chromatography, high-pressure liquid chromatography, mass spectrometry, and NMR spectroscopy, ATR spectroscopy is considerably faster and does not require withdrawal of sample, which can be detrimental for monitoring of labile compounds and for some other applications. [Pg.242]

Although a thorough validation cannot rule out all potential problems, the process of method development and validation would address the most common ones. Examples of typical problems that can be minimized or avoided include interferences that coelute with the analyte in liquid chromatography (LC), a particular type of column that no longer produces the separation needed because the supplier of the column has changed the manufacturing process, an assay method that is unable to achieve the same detection limit after a few weeks, or a quality assurance audit of a validation report that finds no documentation on how the validation was performed. [Pg.749]

Chromatography, the process by which the components of a mixture can be separated, has become one of the prime analytical methods for the identification and quantification of compounds from a liquid or homogeneous gas phase. The principle is based on the concentration equilibrium of the compounds of interest between two phases one of which is called stationary because it is immobilised in a column, the other of which is called mobile because it is the transport mechanism through the system. The differential migration of compounds through the column leads to their separation. [Pg.3]

Figure 3.8 shows an example dataset of mixed hydrocarbons used as a petrochemical feedstock. These are straight-run naphthas which consist of a wide range of alkane, alkene, aromatic and naphthenic hydrocarbons, mainly in the range of C4-C9. The conventional analytical method for naphtha analysis is temperature-programmed gas chromatography (GC), which can provide a full analysis including C-number breakdown, but which is rather slow for process optimisation purposes. [Pg.49]

It was mentioned earlier that empirical multivariate modeling often requires a very large amount of data. These data can contain a very large number of samples (N), a very large number of variables (M), or both. In the case of PAC, where the analytical method is often a form of spectroscopy or chromatography, the number of variables collected per process sample can range from the hundreds to the thousands ... [Pg.243]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...