An open source ventilator is a disaster-situation ventilator made using a freely licensed (open-source) design, and ideally, freely available components and parts (open source hardware). Designs, components, and parts may be anywhere from completely reverse-engineered or completely new creations, components may be adaptations of various inexpensive existing products, and special hard-to-find and/or expensive parts may be 3D-printed instead of purchased.[2][3] As of early 2020, the levels of documentation and testing of open source ventilators was well below scientific and medical-grade standards.[4]
One small, early prototype effort was the Pandemic Ventilator created in 2008 during the resurgence of H5N1 avian influenza that began in 2003, so named "because it is meant to be used as a ventilator of last resort during a possible avian (bird) flu pandemic."[5]
Quality assessment
editThe policy of using both free and open source software (FOSS) and open source hardware theoretically allows community-wide peer-review and correction of bugs and faults in open source ventilators, which is not available in closed source hardware development. In early 2020 during the COVID-19 pandemic, a review of open source ventilators stated that "the tested and peer-reviewed systems lacked complete documentation and the open systems that were documented were either at the very early stages of design ... and were essentially only basically tested ..." The author speculated that the pandemic would motivate development that would significantly improve the open source ventilators, and that much work, policies, regulations, and funding would be needed for the open source ventilators to achieve medical-grade standards.[4]
Design requirements
editA number of features are required for an invasive mechanical ventilator to be safely used on a patient:[6]
- a way of measuring and controlling the volume pumped and the breath rate to avoid volutrauma;
- monitoring for inspiratory pressure, respiratory rate (bpm), and inspiratory-to-expiratory time (I/E) ratio
- for non-sedated patients, an "assist" mode that, instead of forcing air in at a fixed frequency, only increases the pressure when the patient inhales;
- for ARDS, support for setting positive end-expiratory pressure (PEEP) to avoid alveoli collapse;[7][8]
- humidification to avoid drying and cooling the alveoli.[9]
The requirements for non-invasive ventilation are less strict.
COVID-19 pandemic
editOn March 16, 2020,[10] the Open Source Ventilator Ireland (OSV) group was formed[11] [12][13] initially with the goal of building a focus team in Ireland to begin development on what was termed the “Field Emergency Ventilator (FEV)”. Inspired by the initial efforts of the Open Source Medical Supplies (OSCMS),[14] which initially focused on developing open ventilators but quickly refocusing mainly on the local production of Personal Protective Experiment (PPE).[15] OSV Ireland partnered with the OpenLung team[16][17] in Canada, who were developing and publishing open source designs via GitLab.[18] The group quickly grew amassing volunteer engineers, designers and medical professionals with the goal of developing new, low resource medical interventions to support a perceived lack of mechanical ventilation equipment globally. The well-known Bag Valve Mask (BVM) quickly became the core functional component of their design,[19] with the goal of utilizing 3D printed and traditionally manufactured components for localized assembly of the systems to maximise potential manufacturing capabilities around the globe. The Open Source Ventilator Ireland (OSV) group evolved into TeamOSV, to fully incorporate both ventilator and other covid related medical equipment.
The FOSS Initiative OpenVentilator.io project began on March 19, after two weeks of research.[20] Jeremias Almadas [21] had posted some drafts he made on the Open Source COVID-19 Medical Supplies forum.[22] Marcos Mendez contacted him to join efforts to develop a solution that could be reproduced on a very high scale.[23] This project later became the "OpenVentilator Spartan Model". [citation needed]
With the COVID-19 pandemic a new challenge had just arisen, this was no longer to manufacture ventilator, after all, these are manufactured since biblical times,[24] including since the 1960s models like the Bird MK VII [25] were already consolidated with an enviable engineering that is very simple.
The challenge now was to design an item that solves a problem on a global scale. Manufactured on a very large scale and with parts found in small towns and villages. These were the premises assumed by some projects like OpenVentilator.io.[20]
On March 18, Medtronic had opened its code and files for manufacturing its main pulmonary ventilation equipment.[26] The issue was on a scale that Medtronic would not be able to fulfill at the global level, nor at the regional level. The same was already happening with Philips, GE and Drager, world leaders in the manufacture of this type of equipment. It would not make sense to reinvent something that had already been studied for 100 years. The problem was also not an engineering problem, but a logistical and scale problem so that these projects that were to emerge were applicable and achievable. Manufacturing should be decentralized, focused on the regional resources of each individual on planet earth. Nine out of ten Brazilian cities do not even have an ICU bed, let alone an electronics store and or an Ambu factory. The African situation had already been proclaimed a catastrophe.[27]
Several projects are beginning to emerge in this area, many of them with an engineering approach, many others following strict validations with the regulations.[citation needed]
There are few projects that have an [analysis of complex thinking[28][circular reference] within the global economic-political stagnation.[29]
A major worldwide design effort began during the COVID-19 pandemic after a Hackaday project was started, in order to respond to expected ventilator shortages causing higher mortality among severe patients. This project aims to build a continuous positive airway pressure device.[30][non-primary source needed]
On March 19, the MakAir open source ventilator project[31] was started by a team of software engineers in France, using 3D printing to quickly iterate on a prototype, with the goal of letting an established manufacturer produce the final ventilators for a cost nearing €2,000. The team built a working prototype in one month,[32] at the end of which a successful 12 hour ventilation test on a pig was performed. The project received official support[33] from the French Army's investment branch, Agence Innovation Défense of Direction générale de l'armement, granting the project €426,000 to help fund clinical trials. Groupe SEB agreed[34] to manufacture the MakAir ventilator in their facilities in Vernon, France. As of December 2020, the MakAir ventilator project is still active on the engineering side, with full support for both pressure and volume controlled ventilation modes, and on the medical side with ongoing clinical trials at CHU Nantes[35] on human patients.
On March 20, 2020, Irish Health Services[36] began reviewing the designs from the Open Source Ventilator Ireland project.[37] A prototype is being designed and tested in Colombia.[38]
The University of Minnesota Bakken Medical Device Center initiated a collaboration with various companies to bring a ventilator alternative to the market that works as a one-armed robot and replaces the need for manual ventilation in emergency situations. The Coventor device was developed in a very short time and approved on April 15, 2020, by the FDA, only 30 days after conception. The mechanical ventilator is designed for use by trained medical professionals in intensive care units and easy to operate. It has a compact design and is relatively inexpensive to manufacture and distribute. The cost is only about 4% of a normal ventilator. In addition, this device does not require pressurized oxygen or air supply, as is normally the case. A first series is manufactured by Boston Scientific. The plans are to be freely available online to the general public without royalties.[40][41]
The Polish company Urbicum reports successful testing[42] of a 3D-printed, open source prototype device called VentilAid. The makers describe it as a last resort device when professional equipment is missing. The design is publicly available.[43] The first Ventilaid prototype requires compressed air to run.[citation needed]
On March 21, 2020, the New England Complex Systems Institute (NECSI) began maintaining a strategic list of open source designs being worked on.[44][45] The NECSI project considers manufacturing capability, medical safety and need for treating patients in various conditions, speed dealing with legal and political issues, logistics and supply.[46] NECSI is staffed with scientists from Harvard, MIT, and others who have an understanding of pandemics, medicine, systems, risk, and data collection.[46]
Massachusetts Institute of Technology began an emergency project to design a low-cost ventilator that uses a bag valve mask as the main component.[39] Other groups and companies, such as Monolithic Power Systems, also developed designs based on this concept.[47]
The Oxysphere project develops open blueprints for a positive pressure ventilation hood.[48]
On April 23, 2020, NASA reported building, in 37 days, a successful COVID-19 ventilator (named VITAL ("Ventilator Intervention Technology Accessible Locally") which is currently undergoing further testing. NASA is seeking fast-track approval by the United States Food and Drug Administration for the new ventilator.[49][50]
On May 29, 2020, NASA revealed the "Eight US Manufacturers Selected to Make NASA COVID-19 Ventilator."[51]
The U.S. companies selected for licenses are:
- Vacumed, a division of Vacumetrics, Inc. in Ventura, California
- Stark Industries, LLC in Columbus, Ohio
- MVent, LLC, a division of Minnetronix Medical, in St. Paul, Minnesota
- iButtonLink, LLC in Whitewater, Wisconsin
- Evo Design, LLC in Watertown, Connecticut
- DesignPlex Biomedical, LLC in Fort Worth, Texas
- ATRON Group LLC in Dallas
- Pro-Dex, Inc. in Irvine, California
Israeli engineers created an open source ventilator [52]
Disaster-relief provisions
editOn March 24, 2020, the U.S. Secretary of Health and Human Services (HHS) enacted Emergency Use Authorizations[53] to allow the use of additional devices, including: "Ventilators, positive pressure breathing devices modified for use as ventilators (collectively referred to as 'ventilators'), ventilator tubing connectors, and ventilator accessories." This was done in accordance with its February 4 declaration[54] for medical countermeasures against the coronavirus disease 2019, and the equipment is subject to the FDA's "criteria for safety, performance and labeling."
See also
editReferences
edit- ^ "OpenLung - Open Source Ventilator / OpenLung Emergency Medical Ventilator Project / OpenLung BVM Ventilator". GitLab.
- ^ Bender, Maddie (2020-03-17). "People Are Trying to Make DIY Ventilators to Meet Coronavirus Demand". Vice. Retrieved 2020-03-21.
- ^ Toussaint, Kristin (2020-03-16). "These Good Samaritans with a 3D printer are saving lives by making new respirator valves for free". Fast Company. Retrieved 2020-03-17.
- ^ a b Pearce, Joshua M. (2020). "A review of open source ventilators for COVID-19 and future pandemics [version 1; peer review: 1 approved]". F1000Research. 9: 218. doi:10.12688/f1000research.22942.1. PMC 7195895. PMID 32411358.
- ^ "The Pandemic Ventilator". Instructables.com. Retrieved 2020-12-04.
- ^ Real Engineering (4 April 2020). "A Guide To Designing Low-Cost Ventilators for COVID-19". YouTube.
- ^ Manzano, F; Fernández-Mondéjar, E; Colmenero, M; Poyatos, ME; et al. (2008). "Positive-end expiratory pressure reduces incidence of ventilator-associated pneumonia in nonhypoxemic patients". Crit Care Med. 36 (8): 2225–31. doi:10.1097/CCM.0b013e31817b8a92. PMID 18664777. S2CID 19906324.
- ^ Pfeilsticker, FJDA; Serpa Neto, A (August 2017). "'Lung-protective' ventilation in acute respiratory distress syndrome: still a challenge?". Journal of Thoracic Disease. 9 (8): 2238–2241. doi:10.21037/jtd.2017.06.145. PMC 5594148. PMID 28932514.
- ^ Restrepo, R. D.; Walsh, B. K. (1 May 2012). "Humidification During Invasive and Noninvasive Mechanical Ventilation: 2012". Respiratory Care. 57 (5): 782–788. doi:10.4187/respcare.01766. PMID 22546299.
- ^ "Join this Open Source Ventilator Project to give your time and expertise to help develop low-cost ventilators to fight #COVID19. 3D printing and testing is underway so all help is welcomed. Fast action needed". Twitter.com. Retrieved 23 July 2022.
- ^ "Open Source Ventilator Ireland". Opensourceventilator.ie. Archived from the original on 2021-11-15. Retrieved 2022-07-20.
- ^ "There's a Shortage of Ventilators for Coronavirus Patients, So This International Group Invented an Open Source Alternative That's Being Tested Next Week". Forbes.
- ^ Bromwell, Philip (20 March 2020). "Irish project tackles global ventilator shortage". RTÉ.ie.
- ^ "Open Source Medical Supplies". Opensourcemedicalsupplies.org. Retrieved 23 July 2022.
- ^ Bambury, Brent. "Robotics engineer crowd-sources designs for COVID-19 medical supplies to help out-of-stock hospitals". CBC.
- ^ "Open Lung". Openlung.org.
- ^ "Open Source Ventilator, OpenLung Projects Aim to Address the COVID-19 Ventilator Shortfall". Hackster.io.
- ^ "OpenLung · GitLab". GitLab.com. Retrieved 23 July 2022.
- ^ "Ventilator". Teamosv.com.
- ^ a b "OpenVentilator". PopSolutions.co. Archived from the original on 26 February 2021. Retrieved 23 July 2022.
- ^ "Facebook". Facebook.com. Retrieved 23 July 2022.
- ^ "Open Source Medical Supplies Community | Facebook". Facebook.com. Retrieved 23 July 2022.
- ^ "Marcos Méndez". Linkedin.com. Retrieved 23 July 2022. [self-published source]
- ^ "The Long History of the Ventilator, a Machine You Never Want to Need".
- ^ Evelin Stainoff, Ingrid (24 August 2004). "Bird Mark 7" (PDF). GitHub (in Portuguese). Retrieved 29 March 2022.
- ^ "Register to Download Ventilator Files". Medtronic.com.
- ^ "Lack of Covid-19 treatment and critical care could be catastrophic for Africa". Rfi.fr. 3 April 2020.
- ^ pt:Edgar Morin
- ^ "The Great Lockdown: Worst Economic Downturn Since the Great Depression". Blogs.imf.org. Retrieved 23 July 2022.
- ^ Coetzee, Gerrit (2020-03-12). "Ultimate Medical Hackathon: How Fast Can We Design and Deploy an Open Source Ventilator?". Hackaday. Retrieved 2020-03-17.
- ^ "makers-for-life/makair". GitHub. Retrieved 2021-02-18.
- ^ "The Inception of an Open Source Ventilator Project". Journal.valeriansaliou.name. 14 February 2021. Retrieved 2021-02-18.
- ^ "Le ministère des Armées soutient le projet MakAir". Ministère des Armées (in French). Retrieved 2021-02-18.
- ^ "Together to face COVID-19". Groupe SEB. Retrieved 2021-02-18.
- ^ "Safety and Effectiveness Assessment of the MakAir Artificial Ventilator". ICH GCP. Retrieved 2021-02-18.
- ^ Sternlicht, Alexandra. "There's A Shortage Of Ventilators For Coronavirus Patients, So This International Group Invented An Open Source Alternative That's Being Tested Next Week". Forbes. Retrieved 2020-03-21.
- ^ Rodrigo, Chris Mills (2020-03-20). "Irish health officials to review 3D-printed ventilator". The Hill. Retrieved 2020-03-21.
- ^ colombiareports (2020-03-21). "Colombia close to having world's first open source and low-cost ventilator to 'beat Covid-19'". Colombia News | Colombia Reports. Retrieved 2020-03-21.
- ^ a b "MIT E-VENT | Emergency ventilator design toolbox". MIT E-Vent | MIT Emergency Ventilator. Retrieved 2020-03-29.
- ^ Joe Carlson (2020-04-16). "FDA approves production of device designed at University of Minnesota to help COVID-19 patients breathe". Star Tribune.
- ^ Darrell Etherington (2020-04-16). "FDA authorizes production of a new ventilator that costs up to 25x less than existing devices". techcrunch.com. Verizon Media.
- ^ urbicum (2020-03-23). "VentilAid -open source ventilator, that can be made anywhere locally". VentilAid. Retrieved 2020-03-23.
- ^ urbicum (2020-03-23). "GitHub - VentilAid / VentilAid". VentilAid. Retrieved 2020-03-23.
- ^ Fenton, Bruce (March 21, 2020). "Ventilator Project Update: March 21th, 2020 [sic]". Medium. Retrieved March 27, 2020.
- ^ "A list projects to make emergency ventilators in response to COVID-19, focusing on free-libre open source". GitHub. Retrieved March 27, 2020.
- ^ a b Fenton, Bruce (March 14, 2020). "We need Ventilators - We Need You to Help Get Them Built". Medium. Retrieved March 27, 2020.
- ^ "MPS Open Source Ventilator". monolithicpower.com. Retrieved 2020-04-29.
- ^ "Oxysphere – OpenHardware Ventilation Project – Let us Stop Covid together". Archived from the original on 2020-05-13. Retrieved 2020-03-31.
- ^ Good, Andrew; Greicius, Tony (23 April 2020). "NASA Develops COVID-19 Prototype Ventilator in 37 Days". NASA. Retrieved 24 April 2020.
- ^ Wall, Mike (24 April 2020). "NASA engineers build new COVID-19 ventilator in 37 days". Space.com. Retrieved 24 April 2020.
- ^ "Eight US Manufacturers Selected to Make NASA COVID-19 Ventilator". NASA Jet Propulsion Laboratory (JPL). Retrieved 2020-06-02.
- ^ "Israeli engineers created an open source hack for making Covid-19 ventilators". Qz.com. 11 April 2020.
- ^ Health, Center for Devices and Radiological (April 6, 2020). "Emergency Use Authorizations". FDA – via fda.gov.
- ^ "Notice of Declaration under the Public Readiness and Emergency Preparedness Act for medical countermeasures against COVID-19" Archived 2020-04-25 at the Wayback Machine. Department of Health and Human Services Office of the Secretary".
External links
editThis article's use of external links may not follow Wikipedia's policies or guidelines. (January 2023) |
- An overview of open source ventilator initiatives and open regulatory standards.
- Open Source Ventilator community and other COVID supplies, with 2000+ members; 8th design iteration as of March 26.
- The OpenVentilator.Io Spartan Model
- Opensource against covid19.
- Development status, concept and features comparison for open source ventilators projects in a single table.
- Open-source ventilator design, Vanderbilt University
- 7 open hardware projects working to solve COVID-19.
- Open Source Against COVID-19
- Open Source COVID19 Medical Supplies
- OxyGEN Project (ed.). "Emergency ventilator for COVID-19 crisis approved by the Spanish medicine agency". Retrieved 2020-04-13.
- Automation of Bag-Valve-Mask (BVM) using arms and servo-motors. (PDF)
- Garmendia, Onintza; Rodríguez-Lazaro, Miguel A.; Otero, Jorge; Phan, Phuong; Stoyanova, Alexandrina; Dinh-Xuan, Anh Tuan; Gozal, David; Navajas, Daniel; Montserrat, Josep M.; Farré, Ramon (2020-01-01). "Low-cost, easy-to-build non-invasive pressure support ventilator for under-resourced regions: open source hardware description, performance and feasibility testing". European Respiratory Journal. 55 (6): 2000846. doi:10.1183/13993003.00846-2020. ISSN 0903-1936. PMC 7173672. PMID 32312862. Retrieved 2020-04-21.