Jump to content

Melbourne and Hobson's Bay Railway Company 2-2-2WT (1854)

From Wikipedia, the free encyclopedia

Melbourne and Hobson's Bay Railway Company 2-2-2WT (1854)
Type and origin
Power typeSteam
BuilderRobertson, Martin & Smith
Build date1854
Total produced1
Specifications
Configuration:
 • Whyte2-2-2
Gauge5 ft 3 in (1600 mm)
Cylinders2
Cylinder size7.87 in (200 mm) x [?]
bore x stroke
Performance figures
Maximum speed25 mph (40 km/h)
Power output30.0 hp (22.4 kW)
Career
First run9 September 1854
The locomotive was hurriedly built by Robertson, Martin & Smith in time for the inauguration of the Melbourne and Hobson's Bay railway when production of Robert Stephenson and Company's locomotives in the UK was delayed

Melbourne and Hobson's Bay Railway Company 2-2-2WT (1854) was the first locomotive operated after the inauguration of a public railway line in Australia.[note 1] It had 7+78 in (200 mm) diameter cylinders and was capable of producing 30.0 horsepower (22.4 kilowatts), reaching 25 mph (40 km/h) and hauling 130 tonnes (130 long tons; 140 short tons).[2]

On 12 September 1854, the Melbourne and Hobson's Bay Railway Company inaugurated the first railway line to operate in Australia using steam locomotives. The line extended 4.2 kilometres (2.6 mi) from a Melbourne Terminal in Flinders Street and the beach at Sandridge (now Port Melbourne). Four locomotives had been ordered from Robert Stephenson and Company in Newcastle upon Tyne in England, but manufacturing delays made it likely that the railway would be without a locomotive when it opened. The company therefore took the bold step of tasking the Melbourne foundry company Robertson, Martin & Smith, which had never produced one, to construct within 10 weeks a 2-2-2 well-tank locomotive to the design of the railway's chief engineer. The builders achieved the deadline with three days to spare.[1]: 104 

Robertson, Martin & Smith constructed the locomotive at Joseph Raleigh's disused boiling down works on the Saltwater River (now Maribyrnong River) near Footscray, with boiler fabrication being subcontracted to Langlands foundry.[2] The locomotive's total cost was £2700.[3]

Following its trials starting on 9 September 1854, the locomotive hauled the inaugural passenger train at the official opening on 12 September 1854.[3] It continued to do so for three months before the Stephenson locomotives went into service. Its operation was interrupted by down-time on three occasions while broken crank-axles were repaired. During those periods the 0-4-0 locomotive that had hauled ballast wagons during the railway's construction was utilised. However, on 1 December services were ended "until further notice" for an unknown period.[1]: 105 

It is not known when the locomotive was taken out of service and scrapped.

Notes

[edit]
  1. ^ For the previous four months, before the line had opened, a makeshift, company-made 0-4-0 steam locomotive had hauled ballast wagons during the railway's construction.[1]:104

References

[edit]
  1. ^ a b c Harrigan, L.J. (September 1954). "Centenary of the Melbourne-Sandridge Railway". Australian Railway Historical Society Bulletin. Vol. 5 (new series), no. 203. Redfern, NSW: Australian Railway Historical Society, New South Wales Division. ISSN 1449-6291.
  2. ^ a b Oberg, Leon (2007). Locomotives of Australia: 1854 to 2007. Rosenberg Publishing. p. 14. ISBN 9781877058547.
  3. ^ a b "Victoria". Colonial Times. Hobart, Tas.: National Library of Australia. 16 September 1854. p. 2. Retrieved 16 June 2013.

Further reading

[edit]
  • Cave; Buckland; Beardsell (2002). Steam locomotives of the Victorian Railways vol. 1: the first fifty years. Melbourne: Australian Railway Historical Society. ISBN 1-876677-38-4.