Everand Logo

Welcome to Everand!

  • Discover millions of ebooks, audiobooks, and so much more with a free trial

    From $11.99/month after trial. Cancel anytime.

    A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder
    A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder
    A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder
    Ebook236 pages1 hour

    A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder

    By Swinburne Press

    ()

    Read preview

    About this ebook

    This volume contains a collection of classic articles on the subject of designing and building motor boats, with information on equipment, methods, common problems, materials, where to begin, installing motors, and much more. Carefully selected for a modern readership, this timeless volume will be of considerable utility to anyone with a practical interest in boating or sailing, and would make for a fantastic addition to collections of related literature. The articles include: “Boat Building and Boating”, “Canoeing, Sailing, and Motor Boating”, “Motor Boating for All”, “Popular Mechanics Build a Boat for Pleasure or Profit- Build your own Boat”, and “The Motor Boat Manual – With a Special Section on Outboard Motors and Boats”. Many vintage books such as this are becoming increasingly scarce and expensive. We are republishing this volume now in an affordable, high-quality edition complete with a specially commissioned new introduction on boat building.
    LanguageEnglish
    PublisherSwinburne Press
    Release dateSep 17, 2020
    ISBN9781528764117
    A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder

    Related to A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder

    Related ebooks

    Outdoors For You

    View More
    View More

    Related podcast episodes

    Related articles

    • UNLIMITED

      The Perfect Project

      May 14, 2019

      The Perfect Project
      2 min read

    • UNLIMITED

      17-20ft POCKET CRUISERS

      Jan 19, 2023

      17-20ft POCKET CRUISERS
      13 min read

    • UNLIMITED

      Tried & Tested

      Feb 17, 2022

      Tried & Tested
      4 min read

    • UNLIMITED

      Light-air Sailing

      May 15, 2018

      Light-air Sailing
      9 min read

    • UNLIMITED

      10 pocket Cruisers

      May 14, 2021

      10 pocket Cruisers
      6 min read

    • UNLIMITED

      Go For A Blast!

      Sep 2, 2021

      Go For A Blast!
      12 min read

    • UNLIMITED

      Master Your Mainsail

      Aug 13, 2020

      Master Your Mainsail
      11 min read

    • UNLIMITED

      Shoulder Season Sailing

      Oct 13, 2022

      Shoulder Season Sailing
      2 min read

    • UNLIMITED

      Replace Or Rebuild?

      May 12, 2022

      Replace Or Rebuild?
      8 min read

    • UNLIMITED

      We Bought An Adventure Yacht

      Mar 10, 2022

      We Bought An Adventure Yacht
      1 min read

    • UNLIMITED

      Thinking Of Going Electric?

      Mar 16, 2023

      Thinking Of Going Electric?
      4 min read

    • UNLIMITED

      Run To Reach

      Sep 23, 2022

      Run To Reach
      9 min read

    • UNLIMITED

      Woes Of A Wheel Pilot

      Jul 19, 2019

      Woes Of A Wheel Pilot
      3 min read

    • UNLIMITED

      Masterclass

      Sep 8, 2022

      Keeping a boat moving in light airs can be more challenging than dealing with big winds and seas. It requires a huge level of attention to detail and a lot of effort that may seemingly reap low rewards. All sailors will eventually end up in a situati

      4 min read

    • UNLIMITED

      New Yachts

      Mar 10, 2022

      New Yachts
      6 min read

    • UNLIMITED

      International Folkboat

      Feb 15, 2022

      International Folkboat
      2 min read

    • UNLIMITED

      Sail Faster & Safer Downwind

      Nov 10, 2022

      The words ‘pink spinnaker’ are enough to send a chill down the spine of anyone who’s ever watched Cowes Week disaster footage. There’s Atalanta of Chester, which dis-masted when their fuchsia-coloured kite wrapped around the anchor of a tanker in Aug

      14 min read

    • UNLIMITED

      Reviews

      Jul 16, 2019

      Reviews
      10 min read

    • UNLIMITED

      How to Frame a Rob Roy Kayak

      Mar 13, 2020

      How to Frame a Rob Roy Kayak
      14 min read

    • UNLIMITED

      Remote Control Boat

      Jun 29, 2021

      Remote Control Boat
      8 min read

    • UNLIMITED

      Ready For The Show

      Sep 5, 2019

      Ready For The Show
      6 min read

    • UNLIMITED

      Cessna 310 Songbird

      Jan 4, 2022

      Cessna 310 Songbird
      6 min read

    Reviews for A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder

    0 ratings

    0 ratings0 reviews

    What did you think?

    Tap to rate

    Review must be at least 10 words

      Book preview

      A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder - Swinburne Press

      A CHEAP AND

      SPEEDY MOTOR-BOAT

      By Daniel Carter Beard

      THIS boat is intended to slide over the top of the water and not through it, consequently it is built in the form of a flat-bottom scow. Order your wood dressed on both sides, otherwise it will come with one side rough. For the side-boards we need two pine, or cedar boards, to measure, when trimmed, 14 feet (Fig. 228), and to be 16 or 18 inches wide.

      THE STERN-BOARD

      when trimmed, will be 2 1/2 feet long by 1 foot, 8 1/2 inches wide. It may even be a little wider, because the protruding part can be planed down after the boat is built (Fig. 229).

      To make the bow measure from the point E (Fig. 228) 1 foot 8 1/2 inches and mark the point C. Measure along the same line 13 1/2 inches and mark the point D. Next measure from B down along the edge of the boat one inch and mark the point F. Again measure down from B, 5 3/4 inches and mark the point G. With a carpenter’s pencil draw the lines F D and G C and saw these pieces off along the dotted line (Fig. 232). The bow can then be rounded at the points A and B with a sharp knife or jackplane.

      To get the proper slant on the stern, measure from H 4 1/2 inches to L and saw off the triangle LHK. Make the other side board an exact duplicate of the first one, as in Fig. 228. Next set these two boards on edge, like sledge runners (Fig. 230), and let them be 2 feet, 6 inches apart (the boat will be safer if made six inches wider, and its speed will be almost as great), which can be tested by fitting the stern-boards between them before nailing the temporary boards on, which are to hold them in place (Fig. 230). Do not drive the nails home, but leave the heads protruding on all temporary braces, so that they may be easily removed when necessary.

      Now turn the boat bottom side up and nail the bottom on, as already described in previous chapters (Fig. 232). The bottom-boards are to be so planed upon their edges that they leave V-shaped grooves on the inside of the boat to be calked with candle-wick and putty (Fig. 231). Next make a shaft-log by cutting a board in a triangular piece, as shown in Fig. 233, and nailing two other pieces of board on it, and leaving a space for the shaft-rod, over which is nailed a duplicate of the bottom-board, as shown in Fig. 234. Make the shaft-log of three thicknesses of 1-inch plank. To make it more secure there should be a board nailed on the inside bottom of the boat, as shown in Fig. 235 by the dotted lines.

      This board is put there to strengthen the bottom and allow us to cut a slot through for the admission of a shaft (Fig. 236) which is drawn on a scale shown below it. With the engine comes a stuffing box, through which the shaft passes and which prevents the water from coming up through the shaft-hole. The stuffing boxes, which are furnished to fit upon the inside of the boat, are expensive, but one to fit upon the stern of the shaft-log costs but little, and will answer all purposes.

      Of course, when attaching the shaft-log to the bottom, it must be in the exact centre of the boat. Find the centre of the boat at the bow and stern, mark the points and snap a chalk-line between them.

      Now place the shaft-log in position on this line and while holding that there firmly, mark around it with a carpenter’s pencil. Next lay the shaft-log flat on its side with its edge along this line and with your pencil mark on the bottom of the boat the exact place where the shaft-hole must be cut to correspond with the one in the shaft-log. As may be seen by Fig. 236, the shaft runs through at an acute angle; hence the hole must be bored on a slant, or better still a slot cut through the floor long enough to allow for the slant.

      The leak, which would naturally occur here is prevented by the stuffing box which is fastened on to the stern-end of the shaft-log where the latter protrudes for the propeller. To set the engine in the boat it is necessary to have an engine-bed. This is made of two pieces of board cut diagonally, upon which the engine rests.

      Fig. 237 shows a piece of 2-inch board and a method of sawing it to make the duplicate pieces to form the engine-bed. The dimension of these pieces must be obtained by measuring the width of the engine rest, which is to be installed. The angle, of course, must correspond to the angle of the shaft.

      Make your own rudder of any shape that suits your fancy, square or paddle-shaped, of a piece of galvanized iron or of wood, as shown in the diagram; or you can simply fasten the rudder-stem to the transom (stern-board), as is often done on row-boats and sail-boats. If you desire to make your rudder like the one shown here, use two pieces of galvanized pipes for your rudderposts, one of which fits loosely inside of the other. Make the rudder-posts of what is known as 3/8-inch (which means literally a 3/8-inch opening) and for its jacket use a 3/4-inch pipe, or any two kinds of pipe, which will allow one to turn loosely inside the other. The smaller pipe can be bent easily by hand to suit your convenience, after it has been thrust through the larger pipe.

      First bend the lower end of the small pipe to fit your proposed rudder, then remove the larger pipe and flatten the lower end of the small one by beating it with the hammer. To bore the screw-holes in the flattened end you will use a small tool for drilling metal. One of these drills, which will fit any carpenter’s brace, can be procured for the cost of a few cents.

      Drill holes through the flattened end of your pipe for the reception of your screws, which are to secure it to the rudder. It is now necessary to fasten a block of 2-inch plank securely to the bottom of the boat upon the inside where the rudder-post is to be set. This block might best be secured on with four bolts. A hole is then bored through the block and the bottom of the boat a trifle smaller than the largest piece of pipe; the latter is supposed to have screw threads upon its lower end (Fig. 238) so that it may be screwed into the wood, but before doing so coat the threads with white lead and also the inside of the hole in the block with the same substance.

      When the larger pipe is now screwed into the block until its lower end is flushed with the outside bottom of the boat, the white lead will not only make the process easier, but will tend to keep out the moisture and water from the joint.

      From the outside thrust the upper end of the small pipe through the hole in the bottom until it protrudes the proper distance above the larger pipe, and with the point of a nail scratch a mark on the surface of the small pipe where it issues from the big one. At this point drill a hole through the small pipe to admit a nail which is to act as a peg to keep the helm from sliding down and jamming in its bearings.

      If you choose, a small seat or deck may be inserted in the stern, through which the helm extends and which will help to steady it. The top of the helm, or protruding ends of the small pipe may now be bent over toward the bow, as shown in the diagram, and by holding some hard substance under it, the end may be flattened with a hammer and two holes drilled through the flattened end for the rudder-line, as in Fig. 239. These lines work the rudder and extend on each side of the boat through some clothes-lines pulleys, as shown in Fig. 239.

      If you slice off the ring from a common rubber hose and slip it over the inside pipe before you fasten it in place, it will prevent the water from spurting up through the rudder pipe when the boat is speeding.

      Any boat will leak if not carefully built and the simplest kind of a craft carefully put together is as water-tight as the most finished and expensive boat.

      For a gasoline tank any good galvanized iron vessel will answer if it holds five gallons or more of gasoline. It can be placed in the bow on a rest made for it. Of course the bottom of the tank must be on a level or higher than the carburetor of the engine; the tank is connected by a small copper, or block-tin pipe, which you procure with the engine.

      This boat, if built according to plans, should cost ten dollars or less, not counting the cost of the engine. The cost of the latter will vary according to the style of one you use, and whether you get it first or second hand.

      A ten-horse power engine drove a boat of this kind at the rate of eighteen miles an hour. . .

      A chapter from

      Boat-building and Boating, 1931

      MOTOR BOAT FITTINGS

      By Warren H. Miller

      SOUSE my swashbuckets, but there’s a lot of fittin’s about a boat! You won’t say this, you’ll groan it, before they’re all bought; and most of them have to be before she ever leaves the dock. Otherwise, next time you’re down Quarantine way you’re liable to run afoul of a fast launch with a queer flag full of vertical red and white stripes, and before you can manage to disappear she’ll give you the four toots, which signal you will do well to obey, for it says: Heave to! We’re coming alongside to take out your works and see what makes you act so. This means YOU! Presently two leathery officials in navy blue come over the side and begin to look around. "Let’s see ye’re running lights? Hev ye got any?"

      Er,—no; but we’ve a cook for’d with one flaming red nose and two green eyes. Wouldn’t he do for a combination headlight if we stand him up in the bow and let him shut his port eye——

      One hundred, please. Got any life-preservers?

      Stacks of it—in the ice-box; it’s all yours——

      The inspector shakes his head and tries your whistle. One-second squeak, he mutters. Got a fog horn?

      Sure thing! Jim, here, can beller like an Alabama coon when he——

      One hundred bucks——

      What!!

      "I said ‘One hundred dollars’ fine!’ young man, for being at large without side lights, life-preservers, a fog horn, and I don’t know what all besides."

      (Long, panic-stricken pause.)

      Here, officer—take my boat. She’s all I have in the world (sob), and as much as ten dollars couldn’t buy her——

      Oh, it’s harrowing, but it’s much safer, to have all the fittin’s the law requires, besides a whole lot that the far sterner laws of the Sea insist upon—with your life as the penalty of being without them. It’s the most joyful thing in the world to be minus a compass in a thick fog, out of sight of

      Enjoying the preview?
      Page 1 of 1