Allison Transmissions: How to Rebuild & Modify: How to Rebuild & Modify

CHAPTER 1

LCT 1000 AND 2000 ALLISON OPERATION AND SERVICE

Allison Transmission is the world’s largest producer of medium-and heavy-duty transmissions. It was part of General Motors until 2007, when the division was sold to the Carlyle Group and Onex Corporation.

The Allison 1000- and 2000-series transmissions were introduced in 1999 on non-GM applications and in 2001 on GM applications. Production continued for GM applications through the 2019 model year, at which time the transmission was replaced by a 10-speed (10L1000) for 2020-and-later applications. Non-GM applications are still being produced.

General Motors refers to the transmissions as the Light Commercial Truck (LCT) 1000 or 2000, while non-GM applications refer to the transmissions as the A1000 or the A2000. The primary differences between the 1000 and the 2000 is component size, gear ratios, and unit torque capacity. The 2000 uses larger components, which means it can be used in larger vehicles.

General Motors uses the 1000 and 2000 in pickup, van, and medium-duty truck applications equipped with a 6.6L Duramax diesel or an 8.1L Vortec gas engine, although not all van applications with the Duramax use the Allison. Non-GM applications use the 1000 and 2000 transmissions in Peterbilt, Kenworth, Ford, Freightliner, Hino, Isuzu, Sterling, and International truck and bus applications to name a few. Multiple 1000- and 2000-series transmissions are available, depending on the application. The differences between models can be anything from clutch count to whether or not the transmission is equipped with a parking pawl. There are some differences between the General Motors and non-GM applications, so some parts are interchangeable while other components are not.

Since there are differences between the various applications, it is important to properly identify which one is on the lift before ordering parts or a remanufactured unit. Allison units are referred to by the model and a use designation. Allison 1000 models include the 1000, 1350, 1700, and 1750. The 2000 models include the 2100, 2200, 2300, 2350, 2400, 2500, 2650, 2700, and 2750.

The model-use designator further breaks down the model into its vehicle type and application. Each Allison uses a two- or three-digit designator to identify the type of use for which the transmission was designed. The model designation looks like this: A2200MH, A2350PTS, or A2300RDS. Designators can include abbreviations in the following table.

Multiple versions of the 1000- and 2000-series units were used, such as this Allison 2400. Make sure to find out which transmission you are working on. This information is located on the tag. The service process is the same for all versions, but the parts vary greatly and many are not interchangeable.

GM Allison units are available as 5-speed or 6-speed applications, while non-GM applications are available as 5-, 6-, or 7-speed versions. The 6-speed 1000- and 2000-series applications were introduced in the 2006 model year. More than 100 update changes have occurred with the 1000- and 2000-series units. Several of the changes will not back service earlier-model applications.

Generations

Six generations of Allison 1000- and 2000-series applications have been produced. Generations 1 through 3 were used from 1999 to 2005. Generation 4 ran from 2006 to 2012 on non-GM applications and from 2006 to 2014 on GM applications. Generation 5 was used for 2013 to 2021 non-GM applications and from 2015 to 2019 on GM applications. Generation 6 was introduced in 2022.

Keep in mind that GM applications never ran the Generation-6 units, as it is now using the 10L1000 that replaced the LCT 1000. Multiple changes occurred with each generation, so always rely on the unit serial number to access the correct parts and service information for your application.

Transmission Identification

Years ago, the GM numbering system for transmissions was significantly different than it is today. Everything except the Allison 5- and 6-speed applications and some units developed by Aisin Warner and Jatco are numbered using the GM numbering system.

Early Years

Allison’s numbering systems included A, B, S, and M, which designated the application for which the transmission was used (automotive, bus, or marine). Truck applications included units such as the AT542, AT543, and AT545. All of those units were 4-speed applications.

Hydra-Matic and Allison were the GM divisions that provided the transmission engineering and manufacturing for General Motors. Allison quickly became the dominant heavyduty automatic transmission in the heavy-truck market worldwide.

1991

Allison introduced its fully computer-controlled units in the 1990s. Allison introduced its world transmissions as it expanded its lineup into more trucks and buses worldwide. The world transmission led the way for all manufacturers with technology changes that had never been seen before in the automotive and heavy-truck markets.

With the advent of the new transmission designs, Allison changed the designations of the world transmission to include multiple-series units, such as the 1000-, 2000-, 3000-, 4000-, 5000-, 6000-, 8000-, and 9000-series units. Typically, as the series number increases, so does the torque capacity and the physical size of the unit. Generally, the 1000- and 2000-series applications include light- and medium-duty trucks, vans, and buses; 3000- and 4000-series applications include medium- and heavy-duty trucks and buses; and the 5000-, 6000-, 8000-, and 9000-series applications are generally used for off-highway applications, such as mining trucks.

2006 and Later

The years 2006 and later have seen major introductions of GM 6-, 8-, 9-, and 10-speed applications for both rear-wheel-drive and front-wheel-drive vehicles. Again, the designations changed. The E designation is no longer used by General Motors, as all of the 6-, 8-, 9-, and 10-speed applications use fully integrated electronic control systems. The updated transmission designs are now used by GM as well as sold to other manufacturers.

The LCT 1000- and 2000-series applications changed in 2006 from a 5-speed to a 6-speed application. The designation remained the same, but the RPO code for the transmission changed.

2012–2020

Allison introduced a 10-speed version for the heavy-truck market known as the TC10 in 2012. The TC10 was dropped from production in 2020. A new 9-speed unit was introduced in 2022 as a replacement for many of the 2000-series applications. The new unit has some hybrid features, such as start/stop and twomode hybrid operation.

GM Non-Hybrid Transmission Applications

GM’s non-hybrid transmission options include the 6L45, 6L50, 6L80, 6L90, 6T30, 6T35, 6T40, 6T45, 6T50, 6T70, 6T75, 6T80, 8L45, 8L90, 9T45, 9T50, 9T60, 9T65, 10L60, 10L80, 10L90, 10L1000, LCT 1000, LCT 2000, A1000, A1350, A1700, A1750, A2100, A2200, A2300, A2350, A2400, A2500, A2650, A2700, and A2750.

GM LCT 1000 and 2000 North America Usage

The GM LCT 1000 and 2000 were used in the following vehicles in North America:

Silverado, Sierra (C/K Trucks, C = 2WD, K = 4WD)

Express, Savana (G/H Vans, G = 2WD, H = AWD)

Topkick, Kodiak (3500/4500/5500/6500 medium-duty truck)

Car/truck and model/body designations refer to the fourth or fifth digit of the vehicle identification number (VIN) code. The fourth digit is used on cars, and the fifth digit is used on trucks for the body-type designation.

RPO Identification

General Motors has always used a process known as regular production option (RPO) codes to identify the component content for its vehicles. When a dealership orders a vehicle, every option on that vehicle (engine, transmission, axle ratio, radio, brake system, suspension system, air-conditioning system, and all other component options) is given a three-digit alpha numeric designation. That three-digit designation (RPO) is used by the assembly plant to ensure the vehicle is built with the options the dealership ordered. For example, a Chevrolet or a GMC truck may have a Z71 decal on the truck bed, and Z71 is the RPO code for an off-road suspension package.

All RPO codes are three digits. Engine RPOs typically start with the letter L (LT1, LT4, and L88). Rearwheel-drive axle options typically start with the letter G (GT4 and G80), and transmission RPO codes start with the letter M (MT1 and M30). The RPO codes are found on a label known as a service parts identification (SPID) label. The codes are positioned in alpha-numeric order on the label. The SPID label is typically located in one of four locations, depending on the year and vehicle model. Locations include: the glove box, center console, rear decklid (trunk of cars), and on the spare tire cover (cars).

The RPO codes are listed on the RPO tag, which is typically located in the glove box, center console, spare tire cover, or trunk lid for 2018-and-earlier applications. Transmission RPOs start with the letter M, engine RPOs start with the letter L, and rear-wheel-drive final-drive information starts with the letter G. The 5-speed and 6-speed GM LCT 1000 uses either RPO code MW7 or M74. The RPO is often required for parts ordering and to access the correct service information.

During the transition from Generation 4 to Generation 5 Allison applications, vehicles were constructed using components and wiring from both generations. On those transitional applications, RPO AVF was used to designate which transmission control module (TCM) was used, which also determines if the TCM connector is a 66-pin or an 80-pin connector. If the RPO AVF is used, the unit uses the 66-pin connector and its appropriate schematics, and it is configured with Generation 5 components.

GM 2018 and Later

Up to the 2018 model year, the RPO/SPID label was located in one of the positions previously mentioned. Starting with the 2018 model year, General Motors began to transition the label information to a different location and format with new body-styles and vehicle redesigns. The new label requires a smart phone to read a quick-response (QR) code image to access the three-digit codes. The label is now located on the driver-side B-pillar. Open the driver-side door and look at the area below the body striker.

There are apps available for free that work well to read QR codes, including Data Matrix, I-Nigma, QR Scanner, QR Droid, Barcode, and NeoReader. To read the new design label, open the application and position the sight box over the QR label area. The application will read the label and display the RPO codes as well as the VIN and other pertinent information. Most smartphone cameras will also read the QR code. Just open the camera app, point at the QR code, and click on the link that appears.

The RPO tag location and design started to change beginning in the 2018 model year. The new design tag requires a smartphone and a quick-response (QR) reader application (app) to access the vehicle’s RPO information. With the app open, scan the QR label. The app will then display the RPO content on your phone.

Why You Need to Know the RPO

Why is it important to know the RPO code for the component/system that you are attempting to repair? It’s because many components are similar, but there can be some differences. This means that the part being replaced could be different—even though it may appear to be identical. In many instances, the parts person will ask for the option content or the vehicle VIN so that he or she can ensure a buyer gets the correct parts for the specific application. In addition, component repair processes and system wiring vary, so RPO information may be needed to select the correct wiring schematics or repair information.

Transmissions also have their own unique RPOs. The LCT 1000 uses the RPO M74 for the 5-speed and RPO MW7 for the 6-speed RWD applications. The following table lists all the RPO codes for the various GM Hydra-Matic/Allison 5-, 6-, 8-, 9-, and 10-speed applications for light- and medium-duty GM vehicles.

Other Allison applications and their RPO codes used in GM medium-duty truck/bus applications include A1700PTS (MA6), A1700HS (MJ0), A1700EVS (MH1), A1700RDS (MIU), A1700MH (MIX), A1750RDS (MI0), A1750EVS (MHV), A2700PTS (MB6), A2700HS (MWB), A2700EVS (MG0), A2700RDS (MIA), A2700MH (MF0), A2750RDS (MBV), A2750MH (MBW), A2750EVS (MBY), and A2750HS (MBX).

Transmission Tag Information

All Allison transmissions include a tag that helps to identify the transmission. The Allison family of transmissions uses a metal tag that is mounted to a flat surface on the transmission case. The tag is typically located on the passenger’s side of the transmission case. The LCT 1000- and 2000-series tag includes the model year, model code, and serial number.

Cleaning

Take care when cleaning the tag because it can be damaged. Before beginning, take a picture of the tag so that you will have the information available for the parts person if needed. ■

Some information on the tag is important when it comes to ordering parts and determining if your transmission was equipped with certain updates. A parts person may require the model year, model code, and serial number.

Model Year

The model year may not be the same as the year of the vehicle being worked on, depending on the vehicle production date.

Model Code

The model code varies, depending on the vehicle platform and the type of vehicle that the transmission is going into. Later-model Allison applications do not include the model as part of the tag information.

As with the RPO tag, the transmission tag contains a tremendous amount of information about the transmission, including the model code, the serial number, and the build date. Many transmission updates are attached to a specific Allison serial number. So, when ordering parts, the parts person may require the tag information to get the correct parts for the application.

Serial Number

The serial number is the most important number on the tag. Allison identifies the unit series as 1000, 2000, 3000, or 4000 as well as the break points for product updates using the serial number. This means the parts person may need the serial number to order the correct parts.

On GM applications, the parts person may also need the VIN. The first two numbers of the serial number represent the transmission model: 63 or 96 = 1000 or 2000, 65 or 93 = 3000, and 66 or 94 = 4000.

LCT 1000 Unit Specifications

The Allison 1000 and 2000 are used in both GM and non-GM applications. The transmissions are available as 5- and 6-speed models. A stand-alone TCM is used with all applications. The 5- and 6-speeds use the same clutch layouts, with the difference being the hydraulic and electronic systems. There are some part differences between those used in a GM application and those used in a non-GM application.

PTO and Non-PTO Applications

Both Allison and GM applications