TheSamba.com :: VW Special Service Tools

Number	Designation and Application	Tool Photo
B9	Riveting Tool For hub cap spring clips	From Zelenda VW Special Tools Catalog
T1	Board for VW Special Tools (Engine) For the orderly storage of special tools (except measuring instruments) used for the engine
T2	Board for VW Special Tools (Front Axle) For the orderly storage of special tools (except measuring instruments) used for the front axle
T3	Board for VW Special Tools (Transmission and Rear Axle) For the orderly storage of special tools (except measuring instruments) used for the transmission and rear axle
102	T-Wrench 14 mm For loosening and tightening - crankcase bolts and nuts, - exhaust pipe flange bolts, - clutch bolts, - transmission case bolts and nuts, - steering gear case cover bolts of VW Passenger Cars, - steering column flange clamp bolts of VW Passenger Cars, - body mounting bolts of VW Passenger Cars
103	T-Wrench 17 mm For loosening and tightening - crankcase bolts and nuts, - torsion arm link pin clamp bolts, - brake back plate bolts, - spring plate hub cover bolts, - body mounting bolts of VW Passenger Cars
106	T-Wrench 10 mm For loosening and tightening - oil pump nuts, - oil strainer nuts, - intake manifold or preheater pipe nuts and bolts, - oil cooler nuts, - crankcase bolts, - heating control linkage, - bolts for valve push rod guide plates, - bolts on fan housing, - bolts on fan housing halves
109	Box Wrench 10 mm For loosening and tightening nuts on oil cooler
110	Box Wrench 27/30 mm For loosening and tightening cradle nuts on transmission and steering wheel center nut
111	Box Wrench 17 mm Unknown
112	Special Wrench 36 mm with guide plate For loosening - flywheel gland nut - (guide plate prevents the wrench from slipping off the gland nut), - rear axle shaft nuts, - fan nut
112a	Special Wrench 36 mm with guide plate For loosening - flywheel gland nut - (guide plate prevents the wrench from slipping off the gland nut), - rear axle shaft nuts, - special nut on fan
113	Open End Wrenches 27 mm For adjusting - front wheel bearings, - steering worm adjusting sleeve, For holding the pulley on the generator (with the straight type wrench)	Hazet version
113/2	Open End Wrench 27 mm, cranked For adjusting - front wheel bearings, - steering worm adjusting sleeve
113a	Open End Wrenches 32 mm For adjusting front wheel bearings
113a/2	Open End Wrench 32 mm, cranked For adjusting front wheel bearings
113b	Open End Wrenches 24 mm For adjusting front wheel bearings	Hazet version
113b/2	Open End Wrench 24 mm, cranked For adjusting front wheel bearings
113t	Open End Wrenches 32 mm For adjusting front wheel bearings
114	T-Wrench 8 mm, square socket For loosening and tightening - gearshift rod coupling, - screws on selector forks in standard transmission
114-1	T-Wrench 8 mm, square socket - long For loosening and tightening - gearshift rod coupling, - screws on selector forks in standard transmission
116	T-Wrench 13 mm
118	Torque Wrench, 6 mkg (43 lbs./ft.) max For loosening and tightening - rod nut, - head nut Used in conjunction with 14 mm and 17 mm sockets and keys VW 156 (8 mm) and VW 157 (10 mm) for Allen setscrews
118/30	Torque Wrench, 30 mkg (217 lbs./ft.) max For loosening and tightening - drive pinion nut in conjunction with 32 mm socket VW 162, - flywheel gland nut in conjunction with the guide plate of VW 112, - rear axle shaft nut in conjunction with 36 mm socket VW 163a
119	Equipment for measuring the acceleration injection capacity of the carburetor
120	Float needle valve setting tool
121b	Piston ring tool For removing and installing - piston rings
122b	Circlip Pliers For removing and installing - piston pin circlips, - glove compartment lid lock, - circlips in governor
123	Piston Ring Compressing Tool 75 mm dia. For pistons from 75 to 76 diameter
123a	Piston Ring Compressing Tool 77 mm dia. For pistons from 77 to 78 diameter
123b	Piston Ring Compressing Tool 83 mm dia. For pistons from 83 to 84 diameter
123c	Piston Ring Compressing Tool 85.5 mm dia. For pistons from 85.5 to 86.5 diameter
123d	Piston Ring Compressing Tool 90 mm dia. For pistons from 89.5 to 90.0 diameter
124	Chisel (Peening) For securing - connecting rod bolts, - clutch release lever special nut, - hexagon nut of driven gear and shaft
124a	Chisel (Peening) For securing - connecting rod bolts or engine nuts - clutch release lever special nut, - hexagon nut of driven gear and shaft, - clampage nut on the bearing tube
125	Circlip Pliers
125	Tool for inserting Bosch Condenser plug in distributor	From Baum Tools catalog
126	Unknown
126a	Fuel Pump Wrench For removing and installing fuel pump
126b	Fuel Pump Wrench 13 mm For loosening and tightening 13 mm mounting nuts of fuel pump
130	King Pin Pilot Drift 5.9 mm For removing and installing king pins of VW Passenger Cars having lubrication passage 6.0 to 6.5 mm dia., if VW 400 and corresponding tool set are not available
130a	King Pin Pilot Drift 7.9 mm For removing and installing king pins of VW Passenger Cars having lubrication passage 8.0 to 8.5 mm dia., if VW 400 and corresponding tool set are not available
131	King Pin Bush Pilot Drift For removing and installing king pin bushes of VW Passenger Cars, if VW 400 and corresponding tool set are not available
131a	King Pin Bush Pilot Drift For removing and installing - knuckle pin bushes of VW Transporters, - sector shaft bushes of VW Transporters, - steering lever shaft bush in Transporter steering gear case, - lower knuckle pin bush of VW Transporters
131t	King Pin Bush Pilot Drift For removing and replacing king pin bushes and steering arm shaft bushes of VW Transporters, In conjunction with VW 400, VW 401, and VW 412 for removing and installing cam lever shaft bushes in steering gear case of VW Transporters, In conjunction with VW 400, VW 401, and VW 410 for removing upper pivot pin bush of VW Transporters, In conjunction with VW 400, VW 401, and VW 421 for removing lower pivot pin bush of VW Transporters (VW 421 to be inserted in Press arbor)
133	Torsion Arm Link Pin Bush Pilot Drift For removing and installing torsion arm link pin bushes of VW Passenger Cars, if VW 400 and corresponding tool set are not available
133a	Torsion Arm Link Pin Bush Pilot Drift For removing and installing torsion arm link pin bushes
133b	Torsion Arm Link Pin Drift For removing and installing outer needle bearing rings of torsion arm link pins
133t	Torsion Arm Link Pin Bush Pilot Drift For removing and replacing torsion arm link pin bushes of VW Transporters
135	Brake Shoe Pliers
136	Brake Lining Wear Checking Tool For checking the brake lining thickness of disc brakes
W147	Tensioning Device for the Rear Wheel Adjustment - Swing Axle Type 1 Beetle and Type 3 1500/1600
150	Offset Handle For loosening and tightening socket-head screws of front torsion bar center locks (up to Chassis No. 1 397 022) in conjunction with key VW 156
151	T-Handle With VW 156 for releasing and tightening front torsion bar center lock screws (front axle removed) and connecting rod bolts (old type). With VW 157 for releasing cylinder head nuts. Also used in conjunction with other sockets
154	17mm hex socket
155	19mm hex socket
156	Allen Key 8 mm For loosening and tightening - socket-head screws of front torsion bar center locks (up to Chassis No. 1 397 022) - connecting rod bolts having 8 mm socket (earlier type)
157	Allen Key 10 mm For loosening and tightening cylinder head nuts
158	Double Offset Wrench 10 x 14 mm For loosening and tightening the carburetor flange stud nuts
159	Oil Pressure Switch Wrench For removing and installing oil pressure switch
159a	Oil Pressure Switch Wrench 24 mm For removing and installing 24 mm hex oil pressure switch
160	T-handle wrench
160	Offset wrench - 22mm - For backup light switch on transmission	From Baum Tools catalog
161	Compression Tool Pliers For compressing McPherson struts
161	Circlip Pliers
161a	Circlip Pliers For removing and installing - circlip on crankshaft, - circlip on drive pinion, - circlip on hand brake lever pin, - double row ball bearing retaining ring on drive pinion, - circlip on rear axle shaft - distributor drive gear lock ring - lock ring on main drive shaft - circlip on commutator side end plate of VW starter motor For removing retaining ring on rear drive shaft
162	Socket 32 mm For tightening drive pinion nut in conjunction with VW 118/30
W162	Tensioning Device for the Rear Wheel Adjustment - IRS Type 1 Beetle, Type 2 Bus / Transporter and Type 3 1500/1600
163a	Socket 36 mm For tightening - flywheel gland nut, - rear axle shaft nuts
164	Double Box Wrench 19 mm For loosening and tightening rear shock absorber mounting bolts of VW Transporters up to Chassis No. 20-117 901
165	Socket Wrench for Cylinder Head Nuts For loosening and tightening 15 mm cylinder head nuts
170	Socket For loosening and tightening - threaded ring in oil filler - threaded ring in oil breather
171	Spring Clip For holding the cam followers in position while disassembling or assembling the engine
172	Drain Plug Key 17 mm Socket For loosening and tightening - oil drain plugs in transmission case - oil drain plugs in reduction gear case
173	Special Socket For loosening and tightening the gland nut with the automatic clutch in situ
174	Special Socket Wrench M 6 For loosening and tightening the socket head screws on the automatic clutch
175	Special Pliers For removing and installing the hose clips on the warm air connecting pipe between the left heater junction box and the oil bath air cleaner
176	Extractor for Fan For extracting fan from crankshaft
177	Centering Sleeve for Fan Housing For centering the front half of fan housing to the oil return thread on hub of fan
178	Special Wrench for Carburetor Mounting For removing and tightening carburetor mounting nuts
179	Special Wrench 36 mm For adjusting the camber by resetting the eccentric bush on upper torsion arm
180	Open End Wrench 46 mm For screwing and unscrewing the threaded adaptor for heat exchanger on muffler
181	Open End Spanner 42 mm For holding the bolt for rubber stop when unscrewing or screwing up the upper securing nut of front shock absorber
182	Special Wrench (automatic transmission) For adjusting - ring gear - preload of the pinion bearing
183	C Wrench for Round Nut (automatic transmission) For tightening up the round nut for the double tapered roller bearing to prescribed torque For loosening the round nut for the double tapered roller bearing
184	Retainer for the Drive Plate (automatic transmission) For holding the torque converter drive plate whilst loosening as well as tightening the gland nut up to the specified torque
185	Plate for Pressing off the Hub of the Fan For pressing off the hub of the fan from the crankshaft
190	Installing Tool for Crankshaft Seal For installing the crankshaft seal in the crankshaft on the fan side
191	Installing Tool for Crankshaft Seal For installing the crankshaft seal in the crankshaft on the flywheel side
192	Drift Sleeve (Oil Seal - Converter/Automatic Transmission) For driving the oil seal into the differential carrier
193	Drift Sleeve (Oil Seal - Final Drive/Transmission-Diagonal arm axle) For driving - oil seal into the side cover - oil seal into the adjusting ring
194	Drift Sleeve (Oil Seal - Final Drive/Diagonal arm axle) For driving - oil seal into the side cover - oil seal into the adjusting ring - oil seal into the adjusting ring (automatic stickshift)
195	Drift (Oil Seal - Final Drive/Automatic Transmission) For driving - oil seal into the final drive cover - oil seal into the rear axle housing


Hello! Log in or Register \| Help \| Donate \| Buy Shirts	See all banner ads \| Advertise on TheSamba.com