LP or Propane Gas Tank Installation, inspection, controls, repairs:

Here we provide descriptions and photographs of unsafe gas piping, indications of unsafe or improperly operating gas appliances, gas meters, and other gas installation defects are provided. The photo above shows two 24-gallon LP gas tanks installed outdoors on a wobbly unstable base.

This document also provides free sample draft home inspection report language for reporting defects in oil and gas piping at residential properties. Do not copy contents from InspectApedia to other websites.

LP Gas Tank Observations & Gas Tank Safety Recommendations for Home Inspectors & Home Owners

General safety warning: improper installation and even improper inspection and testing methods involving natural or "LP" gas can involve dangerous conditions and risk fire or explosion.

Watch Out: If you smell gas you should leave the building immediately > and should do so without doing anything that could create a spark such as operating a light switch or telephone.

Watch Out: From a safe location, call your gas company's emergency line and/or your fire department.

Article Series Contents

• LP / PROPANE GAS TANKS
  • LP GAS TANK FILL PROCEDURE
  • WHERE to INSTALL ABOVE GROUND LP GAS TANKS
  • WHERE TO INSTALL BELOW GROUND LP GAS TANKS
  • LP GAS CYLINDER GAUGE READING
  • LP PROPANE TANK CODES & STANDARDS
  • LP GAS TANK DATA TAG & AGE
  • LP TANK SAFETY & INSTALLATION DEFECTS
• GAS REGULATORS for LP TANKS
• PROPANE GAS EXPOSURE EFFECTS

Watch out: Immediate LP or natural gas safety hazards: if there is evidence of an LP or natural gas leak at a building, gas odors, for example, you should:

• Do not do anything that is likely to cause a gas explosion,
  
  such as lighting a match, operating an electrical switch, or even using a telephone in the building
• Leave the building immediately
• Notify other building occupants of the safety concern
• Contact the local gas company and/or fire department

LP gas tanks [liquid petroleum gas tanks] are normally placed only outdoors, above ground or (if the tank is designed for it), buried below ground.

Where LP tank regulators can be exposed to the weather, especially in northern climates exposed to freezing weather, they should be protected from water and frost to prevent potentially dangerous damage to the LP gas pressure regulator, shown as the gray disk behind the right-most tank in this photograph of LP gas tanks in the Hudson Valley of New York.

LP gas tank regulators are discussed

at GAS REGULATORS for LP TANKS

How Does the LP Gas Company Fill the LP Gas Tank at a Building?

at left our LP gas tank is being filled by an automatic delivery schedule. Photo courtesy of the author & Bottini Fuels, Poughkeepsie, NY.[9]

There are several ways your LP gas company will know when to make a delivery.

• Automatic LP Gas delivery:
  
  the gas company monitors your usage rate and calculates when to make a delivery based on usage history; if you add or change gas fired appliances at your building you should discuss this modification with your gas vendor to keep deliveries on track.
• On-Demand LP Gas delivery:
  
  you will have to watch the fuel level in your LP gas tank and call your gas vendor when the fuel level is low. Most gas companies prefer to make a delivery when the fuel level in the LP tank is below 20%.
• LP tank swap-out:
  
  In some communities the LP gas company will also deliver smaller LP tanks to replace an empty one at your property.
  
  And if your LP gas use is only from a small portable LP tank then it's up to you to bring the tank to an authorized LP vendor for refill.

If your building uses piped-in natural gas, fuel delivery is continuous through the piping system and of course you won't have an LP gas tank at your property.

Watch out: if you have run out of LP gas entirely your fuel delivery driver may refuse to re-fill the tank unless provision can be made to assure that pilot lights in the building are also re-lit and that the building is safe from risk of a gas leak.

The fuel delivery driver will (or should) refuse to deliver LP gas if he is aware of unsafe conditions such as a leak or nearby open flames.

And since the LP gas delivery truck driver has to pull a heavy gas hose and nozzle from the truck to your LP tank, you don't want to run out of fuel in the dead of winter with deep snow-cover and no path cleared to the LP gas tank.

The LP gas delivery driver will print a receipt that documents the date, time, and quantity of LP fuel delivered to the building.

To protect customers from a dishonest LP gas delivery driver, the fuel meter will not print a receipt if the LP gas delivery truck has moved at all from the time of start of LP gas pumping.

Our driver explained that otherwise, "in the old days" of older LP gas meters, a dishonest driver could drop off LP gas at multiple properties, billing just the last customer for fuel.

Is the LP Gas Tank Supposed to be Filled to the Very Top of the Tank or to 100% on the Gas Gauge?

No.

LP Gas tank fill-volume is typically to 80-85% of capacity, leaving vapor space in the tank.

The LP gas company does not fill the tank to its very top as that would not leave sufficient room for expansion of the liquid fuel as temperatures increase from the temperature of the liquid propane at the time of delivery.

This is an important safety detail: your gas company is not short-changing you.
NOTES: Liquid propane has a comparatively high coefficient of expansion (> 50 psig per °F - O'Brien (2010)

REALLY? NIST in discussing the coefficienty of expansion of propane cites that for propane, at temperatures from about 85K to 650K the pressure will range from 1kPa to 4521 kPa as a function of temperature and pressure.

The same source offers this additional data: Density (Liquid) as a function of Temperature and Pressure Temperature from 85.525 K to 369.89 K
Pressure from 1 kPa to 1000000 kPa - NIST (2014))

Overpressure in the LP tank can cause direct venting of combustible gas to the atmosphere, liquid fuel in the distribution lines, abnormally high and thus unsafe pressures at the appliance, or even a ruptured tank. . - Ramirez et als. (retrieved 2014)

Details are at GAS PRESSURES LP vs NATURAL GAS

How & Where to Install Above Ground Liquid Petroleum Gas Tanks - LP or Bottled Gas Tanks: Clearance Distances

Specifications for Installing & Inspecting Above-ground LP Gas Storage Tanks - gas cylinders not filled on site

These LP Gas tank location clearances for above-ground LP gas tanks are given as measured from the tank's relief valve in any direction away from any potential source of ignition (of a gas leak) or where leaking gas could be drawn into a building window or other vent opening.

If your fuel is piped-in natural gas rather than from an onsite storage tank of LP gas, you will want to

see GAS METER CODES & CLEARANCE DISTANCES.

• Gas tank distance from windows, crawl space openings, fan openings:
  
  Install the above ground LP gas storage tank at least three feet from a building window, crawl space opening, or through-wall exhaust fan opening
• Gas tank distance from appliance air intakes:
  
  Install the above ground LP gas storage tank at least five feet from the air intake to any direct venting appliance (such as a high efficiency gas boiler)
• Gas tank distance from air conditioners:
  
  Install the above ground LP gas storage tank at least ten feet from the nearest window air conditioner to avoid a possible gas leak ignition
• Gas tank fill valve distance from building components: 
  
  If the gas cylinders are to be filled on site, say from a gas delivery truck, the fill valve used to connect the gas hose from the filler truck must be at least ten feet from any exterior source of ignition and from building windows, vent openings, or air intakes.

Sample gas tank inspection report language: Safety: Install secure and level support for the LP gas tank at ... -

if a tank tips over and breaks gas line it could be dangerous. This is an inexpensive item. This item should be handled promptly on establishing gas service for the house, preferably before tanks are filled.

Also see BURIED LP GAS TANK INSTALLATION SPECIFICATIONS

Specifications for Installing & Inspecting Above-ground LP Gas Storage Tanks - gas cylinders that are to be filled on site: Clearance Distances

Below is a common LP gas tank cleareance distance skectch example used by most authoirities, cited from NFPA 58 in its Appendix I.

[Click to enlarge any image]

Reader Question: proper backfill for a buried propane tank

(Sept 15, 2014) Hal said:
I am confused as to the proper backfill for a 1000 gallon propane tank, one supplier uses sand, another limestone. which one is recommended?

Reply:

Hal

The concern with *any* backfill on tanks or piping is to avoid sharp rocks or objects that, through settlement, might perforate or damage the equipment. I'm not sure what sort of limestone nor what size gravel that contractor uses, but sand sounds safer to me.

See the following references for code and specificastions for installing underground propane or LPG Tanks

LPG Propane Tank Codes & Regulations

• FOOD TRUCK/CART LP FUEL STORAGE REGULATIONS - New York City [PDF] retrieved 2021/12/09 original source: https://www1.nyc.gov/assets/fdny/downloads/pdf/business/Support/use-store-LPG-food-cart-commissaries.pdf
• NEW YORK CITY GAS PIPING CODE APPENDIX E [PDF] retrieved 2021/03/31 original source: https://up.codes/viewer/new_york_city/nyc-fuel-gas-code-2014/chapter/E/meters-and-gas-service-piping#E
• NFPA 58: Liquified Petroleum Gas Code, (2014), NFPA 1 Batterymarch Park Quincy, MA 02169-7471 Tel: +1 617 770-3000, or from Mexico toll free: 95-800-844-6058, Website: www.nfpa.org, Excerpt:
  
  The code includes minimum requirements for safe handling during LP gas transfer, including operator qualifications, maximum filling quantity in containers, and pre-transfer inspections to ensure containers are fit for continued service. - http://catalog.nfpa.org/2014-NFPA-58-Liquefied-Petroleum-Gas-Code-
  
  
• NFPA 96: Ventilation Control and Fire Protection of Commercial Cooking Operations (2017) - food truck safety.
• NPGA #412-94 "Installation of Underground LP-Gas Systems", National Propane Gas Association, 1600 Eisenhower Lane, Suite 100, Lisle IL 60532, Tel: 630-515-0600 (1994), Website: http://www.npga.org/, - retrieved 3 Feb 2015, original source: https://www.suburbanpropane.com/pdf/NPGA412-94.pdf
  Excerpts & adaptations or paraphrasing from this source:
  
  This bulletin provides guidelines for the installation and inspection of underground LP-Gas systems and outlines song of the unique problems and conditions inherent in these installations that are not encountered when dealing with aboveground systems.
  
  It is not intended to cover all facets of every application, but is meant to be of general assistance to personnel who install and inspect underground LP-Gas systems."
  
  LPG tank Excavation & Setting Guidelines
  
  Install the container and the rest of the system in accordance with accepted standards such as NFPA 58, and/or the authority having jurisdiction. Make sure tank is located in accordance with spacing requirements. See Figure 1 [in the original document] and NFPA 58.
  ...
  The bottom of the excavation must be level and free of rock:
  
  If rocks are present, a 6-inch bed of sand should be used. For completely buried tanks, the excavation must be dug to a proper depth to provide for the housing dome to extend far enough above ground level to prevent entrance of surface water (1 to 3 inches is common practice), allowing for grading away from the dome. See item 7.
  
  If conditions require it, suitable precautionary measures such as shoring should be taken to prevent cave-ins during excavation.
  ...
  For mounded systems, the same general procedure shall be followed, except that the aboveground surface area of the tank must be covered with at least 1 foot of earth, sand, or other noncombustible, noncorrosive materials such as vermiculite or perlite.
  ...
  In high ground water level areas, provisions shall be made to adequately secure the container to the ground, or to a concrete slab, to prevent flotation. Remember that a properly filled container can float because the density of LP-Gas is about half that of water.
  
  Local soil conditions may require other provisions to allow proper drainage from within housing dome.
  ...
  The container should be set substantially level on a firm foundation (firm earth may be used) and surrounded by earth or sand firmly tamped in place. Backfill should be free from rocks or similar abrasives.
  ...
  Where underground containers are installed in locations subject to vehicular movement, such as automobiles, trucks, tractors, etc., protection shall be provided ...
• Australia & New Zealand LP Gas Code: AS-NZS 5601-1 (2011) (English): Gas installations - Part 1: General installations [By Authority of New Zealand Gas (Safety and Measurement) Regulations 2010 (SR 2010/76)]
  Excerpt:
  
  This Standard contains the mandatory requirements and means of compliance for the design, installation and commissioning of gas installations that are associated with the use or intended use of fuel gases such as natural gas, LP Gas, biogas or manufactured gas.
  
  The user is expected to be familiar with the properties and characteristics of those fuel gases and the principles of combustion, ventilation and flueing applicable to the safe installation and operation of gas appliances.
  
  For New Zealand, these requirements cover gas installations downstream of the point of supply (as defined in the Gas (Safety and Measurement) Regulations 2010. F
  
  or Australia, these requirements cover gas installations downstream of the outlet of -
  
  (a) the consumer billing meter installation;
  
  (b) the first regulator on a fixed gas installation where an LP Gas tank or cylinder(s) is installed on site; or
  
  
  (c) the first regulator on site ...


• "Liquified Petroleum Gas (LPG) Propane Awareness", Massachusetts Department of Fire Services, Massachusetts Firefighting Academy", retrieved 12 January 2015, original source: http://www.mass.gov/eopss/docs/dfs/mfa/student-guides/417-propaneawareness.pdf [copy on file]
• Australia, Victoria: "Gas Safety (Gas Installation) Regulations 1999, S.R. No. 6/1999, retrieved 3 Feb 2015, original source: http://www.legislation.vic.gov.au/
• Canada: Quebec, Regulation Clearance between Propane Tank and Next-Generation Meter: Hydro-Québec Releases Survey Data (2015)
  Excerpts:
  Hydro-Québec reports on progress in its survey of electricity meter installations and inspections of clearance between stationary propane tanks and meters and will publish the data on its Web site.
  The RBQ is of the opinion that a next-generation meter should be located at least three metres from a stationary propane tank.
  
  Hydro-Québec employees are currently making the rounds of customers who have outdoor meters to make sure that there is enough clearance. Remote service interruption is totally safe for the close to a million customers who have their meters indoors.
  
  Hydro-Québec would like to reassure its customers. Only one of the new meter's functions—remote service interruption—is in question. Although the risk has not been confirmed, Hydro-Québec is eliminating any potential risk by deactivating this function.
  
  Hydro-Québec recently sent out a notice to all installers, reminding them not to replace any electricity meter if the installation is not up to code. Gas suppliers also have a responsibility to install propane tanks at the regulation distance where the meter location is known.
• U.K. Liquified Petroleum Gas (LPG) Regulations: SAFE USE OF LIQUEFIED PETROLEUM GAS (LPG) AT SMALL COMMERCIAL AND INDUSTRIAL BULK INSTALLATIONS [PDF], - retrieved 3 Feb 2015, original source: http://www.hse.gov.uk/gas/lpg/safeuse.htm
  Excerpts:
  When the risks are properly identified and managed, LPG can be safely used as a fuel source for many applications. This information is aimed primarily at users of LPG to provide information and help to ensure it is used safely.
  
  

Installation Specifications for Below-ground LP Gas Storage Tank: Clearance Distances

Ten-Foot Clearance Rules for Underground LPG Storage Tanks

• Install the below-ground (buried) LP gas storage tank at least ten feet from the nearest window air conditioner to avoid a possible gas leak ignition
• Install the below-ground (buried) LP gas storage tank at least ten feet from the nearest crawl space vent opening.
• Install the below-ground (buried) LP gas storage tank at least ten feet from the nearest building wall
• Install the below-ground (buried) LP gas storage tank at least ten feet from the air intake to any direct venting appliance
• Install the below-ground (buried) LP gas storage tank at least ten feet back from the property line
• Install the below-ground (buried) LP gas storage tank at least ten feet from an "important building" [presumably we exclude things like garden sheds] or from abutting property that may later have a building constructed on it.

We provide additional ABOVE GROUND LP GAS TANK INSTALLATION SPECIFICATIONS and for gas tanks or gas cylinders.

Specifications for Finding, Inspecting, Installing Buried LP Gas Tanks

How to Find a Buried LP Gas Tank

Finding a buried LP gas tank should not be difficult at a property, since the top of the tank has to be accessible for filling and inspection.

Look for the access cover, usually white steel on older LP gas cylinders or black plastic covering an access well on new buried LP gas tanks, as we mention next.

At some new properties you may first have to see and recognize the plastic access well and cover such as the buried LP gas tank cover shown in these photographs.

When the buried LP gas tank access cover is opened, the buried LP gas tank fill valve and regulator are plainly visible as should be a gauge indicating the remaining amount of LP gas in the tank.

How to Find & Read the LP Gas Tank Gauge Guide

The LP tank gauge is installed at a fitting either on the tank top itself or on a combination fitting at the tank top where the gas valves and connections are also installed.

This Liquid Petroleum Gas Tank Gauge - LP tank gauge or bottled gas tank gauge shows us that it is intended for installation on a 200 Lb. LP gas cylinder, and that the tank is at about 40% full.

LP Gas tanks are normally filled before the tank is totally empty. The liquid petroleum gas delivery truck driver can assure that no contaminants have leaked into the tank if it is still under pressure.

LP tanks are usually not filled to 100% of tank capacity, since doing so would risk sending liquefied LP gas out of the gas tank and into the regulator where it could cause damage or be unsafe.

The curved graph at the upper end of the LP gas gauge dial shows the effects of temperature on the LP gas stored in the tank and thus on the effective remaining amount of fuel in the tank.

Some smaller LP gas cylinders may lack a gauge. When a gas cylinder has no percentage-full gauge and we want to know if the tank is empty or nearly so, we gently rock the tank (be careful not to cause a gas leak).

If the tank is heavy and hard to move it's probably nearly full.

A bit of experience with pushing slightly on the tank just before and just after it has been filled by your LP gas delivery company can make it easy to have a general idea of the level of fuel in the tank.

Be sure that LP gas cylinders are not so loose or poorly supported that they can tip over - risking injury or even a gas leak and explosion!

LP Gas Tank Data Tag & Age Information

Our photis shows the data tag for a residential propane tank installed in Two Harbors, Minnesota. You can, with a bit of careful wiping-off of dirt and dust, note that this tank was made in 1997.

...

[Click to enlarge any image]

Our service technician said that the oldest tank he's encountered in the area was from the 1940s and that they do not have a program that requires replacing LP gas tanks based on age - a requirement that you may encounter in some jurisdictions.

Above and below: this LP gas tank installed in a home in San Miguel de Allende, Mexico, in 1992, was replaced in 2017 by the gas supplier. The company was no longer willing to re-fill the old tank, as their drivers considered it unsafe.

The new, replacement lP tank is shown below as it was being filled for the first time.

LP Gas Tank Home Safety Tips & Inspection Report Language Examples

Here are some LP gas safety recommendations and home inspection report examples:

LP Gas Cylinder that is Incompletely Buried

Propane Gas Tank Safety Recommendations: The liquid propane gas tank at ... is partially buried

- this may not be a recommended building practice; accelerated rust may lead to failure of the container. Please review this question with the gas supply company.

Propane Gas Tank Safety Recommendations:

Be sure that the safety relief valve and controls atop the LP gas tanks outside are protected from icing (for example from exposure to rain or gutter overflow). Iced controls can prevent proper operation of safety devices.

...

---

---

ADVERTISEMENT

---

---

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs

On 2021-10-20 by inspectapedia.com.moderator (mod) - clearance distance is given for LP or propane tanks.

@Fritz F,

Please look in the article above on this page where you will see several clearance distance is given for LP or propane tanks. Do let us know if any of that is unclear.

Above on this page where it says:

“These LP Gas tank location clearances for above-ground LP gas tanks are given as measured from the tank's relief valve in any direction away from any potential source of ignition (of a gas leak) or where leaking gas could be drawn into a building window or other vent opening.”

And then review the NFPA diagram above on this page for the distances shown for the different items you ask about as this is used by most authorities.

Keep in mind, of course, that federal, state, and local ordinances must be followed at all times. You can always check with your local building authority if you aren’t confident in the propane companies’ answers.

On 2021-10-20 by Fritz F

What is the proper spacing distance of a horizontal 250 gallon above-ground LP tank from a house wall, windows, heat pump and fixed generator? Are the spacing distances measured from the fill valve, the pressure relief valve, or any closest part of the tank?

I’ve gotten two different answers from two different propane companies, and I’m not sure that either one is according to code or the standard NFPA spacing diagram. Thanks.

On 2021-04-01 by (mod)

@John,

Thank you for continuing to press for usable detail on exact clearance distances for LP regulators and other LP components.

In the article above, at the section titled

Specifications for Installing & Inspecting Above-ground LP Gas Storage Tanks - gas cylinders that are to be filled on site: Clearance Distances

you will see an illustration that you can click-on to see an enlarged, detailed version from which I excerpt below.

You'll see that the "code" illustrators draw clearance distance lines from the point of concern to the closest point of the cover over the LP tank gas valve and regulator assembly.

Most-often that's take as from the closest point on the cover over the LP tank gas valve and regulator assembly to the closest point on the item in question - window, electrical panel, etc. So you'd measure from closest point on the cover if the regulator is under the cover, or on the vent if you're permitted to relocate it, to the closest point on the exterior of the electrical box.

But watch out: in some installations the regulator is not under that cover but instead is nearby, attached to the building wall.

Rather than get into an argument with a building inspector, IMO it makes sense from a safety view as well as a cost and time view, to locate LP tanks and regulators far enough away from points of concern that there is no ambiguity.

In your specific case you're going need to ask if moving the regulator-vent outlet using sufficiently sized- and properly-located- pipe will satisfy the local code inspector who's the final authority.

On 2021-04-01 by (mod)

@John,

Thank you for continuing the discussion, it's helpful. I don't have an authoritative answer, because in my experience the details of exactly which point on the gas regulator or vent when measuring clearance is inconsistent. Ultimately the decision seems to be in the hands of the local code compliance inspector.

Remember that there are two separate clearance topics. One is the risk of creating an explosion by having an ignition source to close to the gas regulator vent. The other is a requirement for adequate working space around gas meters and valves and equipment.

On 2021-04-01 by John

thank you for your time to respond. I reviewed the reference but an still unclear if the distance requirements typically referenced apply to the regulator body or the opening of the vent (Assuming it is piped somewhere.) Thank you.

On 2021-03-31 by (mod)

@John,

I have seen local plumbing inspectors or gas company installers willing to approve an exception to gas meter clearances in some cases - the local official is the final legal authority.

For example, in the Town of Poughkeepsie, New York, where new gas meters are installed outside, when we built an addition to an existing home the gas meter would have ended up indoors - and would have had to be relocated. But the local inspector was satisfied with leaving the meter in place provided its vent was extended to the building exterior.

An example of this cited in local building codes can be found in New York City's "Appendix E Meters and Gas Service Piping"

E.1 General

This appendix addresses the requirements for meters and service piping, underground or aboveground, as the piping enters the building. Service piping includes fuel-gas piping, valves, and fittings upstream of the point of delivery. Service piping may include piping supplied by the gas service utility.

E.2.2

When located inside the building, each regulator shall be provided with a vent pipe that leads directly to the outdoor air. The vent pipe shall be sized according to local utility requirements. The vent outlet shall not be located under a window or any opening leading back into the premises or located below any overhang or projection. No gas regulator vent outlet shall be covered over, plugged up, or otherwise obstructed, and all gas vents shall be identified by suitable marking on the outlet on the outside of the building.

Watch out: there are additional important gas piping and meter location constraints, such as maximum distances from the service line valve to the gas pressure regulator.

Here is a complete copy of this example code:

NEW YORK CITY GAS PIPING CODE APPENDIX E [PDF]

https://inspectapedia.com/plumbing/NYC-Gas-Code-Appendix-E-Meters-and-Gas-Service-Piping.pdf

retrieved 2021/03/31 original source: https://up.codes/viewer/new_york_city/nyc-fuel-gas-code-2014/chapter/E/meters-and-gas-service-piping#E

On 2021-03-31 by John

Hello I have a buried LP tank approximate 25' from the corner of my home. At the entrance to the home there is a pressure regulator mounted on the back exterior wall with a vent extension of 6'. Presumable to move the vent away from the basement window and meter box. Question: Can I install an RV panel 50 outlet with breakers above the gas regulator if it is remotely vented? Can you point to a reference showing this? thank you.

On 2020-08-11 by Tom

I am going to "gang" a second 120 gallon propane tank with my existing 120 gallon tank (both above ground) to increase my propane capacity for a pool heater. If I place the second tank next to the exisiting tank close to the house, the second tank will be close to the clothes dryer vent for the laundry room. The vent will not be blocked, but it will be within one foot of the tank. I don't believe this constitutes an ignition source. Any issues??

On 2019-06-28 by danjoefriedman (mod)

You should ask him why he's doing that. If he's not just entertaining himself it may be that he's listening to the change in Pitch of the ringing tank as a way to get an idea how full it is getting.

On 2019-06-27 by Rita

Why beat on home gas tank when filling with the lid? The gas man does this all the time.

On 2018-01-26 by (mod) - buried LP tank within 10 feet of public foot-path

John in the article above you'll find this clearance distance sketch

https://inspectapedia.com/plumbing/Above_Ground_LP_Tank_Clearance_Distances.jpg

but of course the final legal authority is your local building and zoning department.

On 2018-01-26 by John

Please would anyone know the answer to this:
We have a little used public footpath running through our property. Can I bury an LPG gas tank within 10' of this.

Thanks

John

...

Continue reading  at GAS BTUH, CUBIC FEET & ENERGY where we discuss LP tank sizes and BTU capacity and lasting time, or select a topic from the closely-related articles below, or see the complete ARTICLE INDEX.

Or see GAS TANKS LP / PROPANE FAQs - questions & answers posted originally on this page.

Or see these

Recommended Articles

• GAS APPLIANCE CONVERT LP-to-NATURAL GAS
• GAS APPLIANCE CONVERT REGULATOR NATURAL GAS-to-LP
• GAS APPLIANCE OPERATION at HIGH ALTITUDE
• GAS BTUH, CUBIC FEET & ENERGY
• GAS COOKTOP INSTALLATION
• GAS METER CODES & CLEARANCE DISTANCES
• GAS PIPING CLEARANCES, CODES & DEFECTS
• GAS PRESSURES LP vs NATURAL GAS
• GAS REGULATORS & APPLIANCE / HEATER CONTROLS
• GAS REGULATOR ADJUSTMENT PROCEDURE
• GAS REGULATORS for LP TANKS
• GAS REGULATOR TEST PROCEDURES
• GAS REGULATORS, TWO STAGE
• GAS SUPPLY for ELECTRIC GENERATORS
• GAS TANKS LP / PROPANE
• PROPANE GAS EXPOSURE EFFECTS

Suggested citation for this web page

GAS TANKS LP / PROPANE at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.

Or see this

INDEX to RELATED ARTICLES: ARTICLE INDEX to GAS APPLIANCES, PIPING, CONTROLS

Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia

Ask a Question or Search InspectApedia

Try the search box just below, or if you prefer, post a question or comment in the Comments box below and we will respond promptly.

Note: appearance of your Comment below may be delayed: if your comment contains an image, photograph, web link, or text that looks to the software as if it might be a web link, your posting will appear after it has been approved by a moderator. Apologies for the delay.

Only one image can be added per comment but you can post as many comments, and therefore images, as you like.
You will not receive a notification when a response to your question has been posted.
Please bookmark this page to make it easy for you to check back for our response.

---

 

IF above you see "Comment Form is loading comments..." then COMMENT BOX - countable.ca / bawkbox.com IS NOT WORKING.

In any case you are welcome to send an email directly to us at InspectApedia.com at [email protected]

We'll reply to you directly. Please help us help you by noting, in your email, the URL of the InspectApedia page where you wanted to comment.

Citations & References

In addition to any citations in the article above, a full list is available on request.

---

ADVERTISEMENT

---